Engineering Papers⌕ Search

Engineering topics

Liu, Jun

Publications and source records attributed to Liu, Jun.

At least 883 records · Page 49

Effect of entropy of lithium intercalation in cathodes and anodes on Li-ion battery thermal management

The entropy changes (ΔS) in various cathode and anode materials, as well as complete Li-ion batteries, were measured using an electrochemical thermodynamic measurement system (ETMS). LiCoO 2 has a much larger entropy change than electrodes based on LiNi x Co y Mn z O 2 and LiFePO 4 , while lithium titanate based anode has lower entropy change compared to graphite anodes. Reversible heat generation rate was found to be a significant portion of the total heat generation rate. The appropriate combinations of cathode and anode were investigated to minimize reversible heat.

25 ENERGY STORAGE↗

Enhanced Lithium-ion intercalation properties of coherent hydrous vanadium pentoxide-carbon cryogels nanocomposites

Coherent hydrous vanadium pentoxide (V2O5•nH2O) - carbon cryogels (CCs) nanocomposites were synthesized by electrodeposition of vanadium pentoxide onto the porous carbon scaffold which was derived from resorcinol (R) and formaldehyde (F) organic hydrogels. As-fabricated nanocomposites were characterized by scanning electron microscopy (SEM), along with EDAX and nitrogen sorption isotherms which suggested vanadium pentoxide incorporated in the pores of carbon cryogels. The nanocomposites showed much improved discharge capacity and better cyclic stability as compared to hydrous vanadium pentoxide films deposited on platinum foil. The discharge capacity of the nanocomposites reached 280 mAh/g based on the mass of the vandium pentoxide at a current density of 100mA/g and it possessed good cycle stability at different discharge rate. The results demonstrated that electrochemical performances, such as specific discharge capacitance and reversibility of the composite electrode, could be greatly enhanced by the introduction of carbon cryogels (CCs) scaffold with three-dimensionally interconnected porous structure in which V2O5•nH2O homogeneously dispersed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Local Release of Highly Loaded Antibodies from Functionalized Nanoporous Support for Cancer Immunotherapy

We report that antibodies can be loaded in functionalized mesoporous silica (FMS) with super-high density to provide long-lasting local release at a given site. Preliminary data indicate that FMS-antibody injected directly into a mouse melanoma induces a greater inhibition of tumor growth than seen in various controls, including the antibody injected intraperitoneally. Our findings introduce a novel approach for local delivery of therapeutically active proteins to tumors and potentially, other diseases.

59 BASIC BIOLOGICAL SCIENCES↗

A graphene-based electrochemical sensor for sensitive detection of paracetamol

An electrochemical sensor based on the electrocatalytic activity of functionalized graphene for sensitive detection of paracetamol is presented. The electrochemical behaviors of paracetamol on graphene-modified glassy carbon electrodes (GCEs) were investigated by cyclic voltammetry and square-wave voltammetry. The results showed that the graphene-modified electrode exhibited excellent electrocatalytic activity to paracetamol. A quasi-reversible redox process of paracetamol at the modified electrode was obtained, and the over-potential of paracetamol decreased significantly compared with that at the bare GCE. Such electrocatalytic behavior of graphene is attributed to its unique physical and chemical properties, e.g., subtle electronic characteristics, attractive π–π interaction, and strong adsorptive capability. The sensor shows great promise for simple, sensitive, and quantitative detection of paracetamol.

47 OTHER INSTRUMENTATION↗

Exfoliated MoS2 Nanocomposite as an Anode Material for Lithium Ion Batteries

Nanocomposites of molybdenum disulfide (MoS2) and poly(ethylene oxide) (PEO) were prepared by the exfoliation/absorption method that involved the hydrolysis of lithiated MoS2 in an aqueous solution of PEO. The absorption and subsequent interaction of PEO on the colloidal MoS2 formed a nanocomposite which restacked into layered secondary particles. X-ray diffraction and high resolution TEM indicated that highly disordered nanocomposites were produced when the Lix(PEO)yMoS2 stoichiometry was limited to y < 1. An improvement of greater than 5x in capacity accompanied by high cycle stability and efficiency was observed for the disordered nanocomposites providing a novel approach to utilize low-cost MoS2 and similar materials for a high capacity energy storage system.

25 ENERGY STORAGE↗

Graphene Based Electrochemical Sensors and Biosensors: A Review

Graphene, emerging as a true 2-dimensional material, has received increasing attention due to its unique physicochemical properties (high surface area, excellent conductivity, high mechanical strength, and ease of functionalization and mass production). This article selectively reviews recent advances in graphene-based electrochemical sensors and biosensors. In particular, graphene for direct electrochemistry of enzyme, its electrocatalytic activity toward small biomolecules (hydrogen peroxide, NADH, dopamine, etc.), and graphene-based enzyme biosensors have been summarized in more detail; Graphene-based DNA sensing and environmental analysis have been discussed. Future perspectives in this rapidly developing field are also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facile synthesized nanorod structured vanadium pentoxide for high-rate lithium batteries

Nano-structured vanadium oxide (V2O5) is fabricated via facile thermal-decomposition of a vanadium precursor and vanadyl oxalate produced by reacting micro-sized V2O5 with oxalic acid. The V2O5 nanorods produced by this method exhibit much better electrochemical performance than commercial micro-sized V2O5. The optimized-nanorod electrodes with a high density of (001) planar defects give the best specific discharge capacities of 270 mAh g-1 at C/2 (147 mA g-1) coupled with good cycle stability with only 0.32% fading per cycle. Even at a high rate of 4C (1176 mA g-1), the nanorod electrode still delivers 198 mAh g-1. These results suggest that the nanostructured V2O5 is a good cathode for high-rate, lithium-ion battery applications.

25 ENERGY STORAGE↗

Ammonia-treated Ordered Mesoporous Carbons as Catalytic Materials for Oxygen Reduction Reaction

Polymer electrolyte membrane fuel cells (PEMFCs) have been considered as promising alternative power sources for many mobile and stationary applications. Compared to the fast hydrogen oxidation at the anode, the sluggish oxygen reduction reaction (ORR) at the cathode requires high-performance catalysts. Currently, platium (Pt) nanoparticles supported on high surface area carbons remain the best catalysts for ORR. However, both instability and high cost of Pt-based catalysts represent two main obstacles limiting the commercial applications of PEMFCs. The instability of supported Pt catalysts is mainly due to the corrosion of carbon support under operation conditions and the agglomation and detachment of Pt particles, leading to a decrease in catalytic surface areas. Development of corrosion resistant supports and enhancement of the interactions between Pt and supports are two strategies to improve the cathode long-term activity.

08 HYDROGEN↗

A novel cold-regulated gene from Camellia sinensis, CsCOR1, enhances salt- and dehydration-tolerance in tobacco

In present research, the full-length cDNA and the genomic sequence of a novel cold-regulated gene, CsCOR1, were isolated from Camellia sinensis L. The deduced protein CsCOR1 contains a hydrophobic N-terminus as a signal peptide and a hydrophilic C-terminal domain that is rich in glycine, arginine and proline. Two internal repetitive tridecapeptide fragments (HSVTAGRGGYNRG) exist in the middle of the C-terminal domain and the two nucleotide sequences encoding them are identical. CsCOR1 was localized in the cell walls of transgenic-tobaccos via CsCOR1::GFP fusion approach. The expression of CsCOR1 in tea leaves was enhanced dramatically by both cold- and dehydration-stress. And overexpression of CsCOR1 in transgenic-tobaccos improved obviously the tolerance to salinity and dehydration.

60 APPLIED LIFE SCIENCES↗

Sensitive Immunosensor for Cancer Biomarker Based on Dual Signal Amplification Strategy of Graphene Sheets and Multi-Enzyme Functionalized Carbon Nanospheres

A novel electrochemical immunosensor for sensitive detection of cancer biomarker α fetoprotein (AFP) is described that uses a graphene sheet sensor platform and functionalized carbon nanospheres (CNSs) labeling with horseradish peroxidase-secondary antibodies (HRP-Ab2). Greatly enhanced sensitivity for the cancer biomarker is based on a dual signal amplification strategy: first, the synthesized CNSs yielded a homogeneous and narrow size distribution, which allowed several binding events of HRP-Ab2 on each nanosphere. Enhanced sensitivity was achieved by introducing the multi-bioconjugates of HRP-Ab2-CNSs onto the electrode surface through sandwich immunoreactions. Secondly, functionalized graphene sheets used for the biosensor platform increased the surface area to capture a large amount of primary antibodies (Ab1), thus amplifying the detection response. This amplification strategy is a promising platform for clinical screening of cancer biomarkers and point-of-care diagnostics.

60 APPLIED LIFE SCIENCES↗

Structural rearrangements in self-assembled surfactant layers at surfaces

The transition from compact to extended configuration in ionic surfactant layers under the influence of salt, surfactant surface density and temperature is studied using the classical density functional theory (cDFT). The increase in ionic strength of aqueous salt solution or in surfactant surface density leads to the transition from the hemicylindrical to the perpendicular monolayer configuration of the molecules. Although producing the same structural rearrangement in the surfactant layer the origin of the effect of salt and surface density is different. While the addition of salt increases the out-of-plane attractive interactions with the solvent, the increase in density results in the increase in the in-plane repulsion in surfactant layer. The temperature effects are subtler and are mainly manifested in the reduction of the solution structuring at elevated temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nitrogen-doped mesoporous carbon for energy storage in vanadium redox flow batteries

We demonstrate a novel electrode material-nitrogen-doped mesoporous carbon (NMC)-for vanadium redox flow batteries. Mesoporous carbon (MC) is prepared using a soft-template method and doped with nitrogen by heat-treating MC in NH 3 . NMC is characterized with X-ray photoelectron spectroscopy and transmission electron microscopy. The redox reaction of [VO] 2+ /[VO 2 ] + is characterized with cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalytic kinetics of the redox couple [VO] 2+ /[VO 2 ] + is significantly enhanced on NMC electrode compared with MC and graphite electrodes. The reversibility of the redox couple [VO] 2+ /[VO 2 ] + is greatly improved on NMC (0.61 for NMC vs. 0.34 for graphite). Nitrogen doping facilitates the electron transfer on the electrode/electrolyte interface for both oxidation and reduction processes. NMC is a promising electrode material for redox flow batteries.

25 ENERGY STORAGE↗

Solvothermal synthesis of copper sulfide semiconductor micro/nanostructures

Covellite copper sulfide (CuS) micro/nanometer crystals in the shape of hierarchical doughnut-shaped, superstructured spheric-shaped and flowerlike architectures congregated from those nanoplates with the thickness of 20-100 nm have been prepared by a solvothermal method. The as-obtained CuS products were characterized by means of scanning electron microscopy (SEM), X-ray diffractometry (XRD) and energy-dispersive X-ray spectroscopy (EDS). A systematic investigation has been carried out to understand the factors influencing the evolution of CuS particle morphology which found to be predominant by solvent, surfactant, sulfur resource and copper salt. The possible formation mechanism for the nanostructure formation was also discussed. These CuS products show potential applications in solar cell, photothermal conversion and chemical sensor.

36 MATERIALS SCIENCE↗

Vapor-Induced Solid-Liquid-Solid Process for Silicon-based Nanowire Growth

Silicon based nanowires have been grown from commercial silicon powders under conditions of differing oxygen and carbon activities. Nanowires grown in the presence of carbon sources consisted of a crystalline SiC core with an amorphous SiOx shell. The thickness of SiOx shell decreased as the oxygen concentration in the precursor gases was lowered. Nanowires grown in a carbon-free environment consisted of amorphous silicon oxide with a typical composition of SiO1.8. The growth rate of nanowires decreased with decreasing oxygen content in the precursor gases. SiO1.8 nanowires exhibited an initial discharge capacity of ~ 1,300 mAh/g and better stability than those of silicon powders. A Vapor Induced Solid-Liquid-Solid (VI-SLS) mechanism is proposed to explain the nanowire growth (including silicon and other metal based nanowires) from powder sources. In this approach, both a gas source and a solid powder source are required for nanowire growth. This mechanism is consistent with experimental observations and can also be used to guide the design and growth of other nanowires.

Environmental Molecular Sciences Laboratory↗

Gas-Induced Expansion and Contraction of a Fluorinated Metal-Organic Framework

Synthesis and gas sorption properties of a novel fluorinated MOF using the commercially available 2,2-Bis(4-carboxyphenyl)hexafluoropropane is reported with high selectivity toward CO2, H2S, and SO2 as well as breathing motion upon solvent removal and gas inclusion

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimization of Air Electrode for Li/Air Batteries

The effects of carbon microstructure and carbon loading on the performance of Li/air batteries were investigated. The active carbons from various sources were compared, and a dry rolling method was optimized to prepare air electrodes with high mesopore volume. It is found that the capacities of air electrodes improve significantly when the mesopore volume of the carbon source is high. However, for carbons with low mesopore volumes, other factors such as surface activity also play an important role in determining the electrochemical performances of the Li/air batteries. A practical criterion, area-specific capacity, was used to optimize the carbon loading for air electrode. The best area-specific capacity of 13.1 mAh/cm2 was obtained at a carbon loading of 15.1 mg/cm2. Further increasing or decreasing the carbon loading led to a reduced area- specific capacity. Finally, at fixed carbon loading and discharge rates, electrolyte amount was another key factor governing cell performance. A spring mechanism is proposed to explain the formation of the tri-phase regions in air electrodes. After optimizing the parameters listed above, a high capacity of 1,756 mAh/g carbon corresponding to a specific energy of 4,614 Wh/kg carbon was obtained for Li/air batteries operated in a dry air environment.

25 ENERGY STORAGE↗

Ternary Self-Assembly of Ordered Metal Oxide-Graphene Nanocomposites for Electrochemical Energy Storage

Surfactant or polymer directed self-assembly has been widely investigated to prepare nanostructured metal oxides, semiconductors and polymers, but this approach is mostly limited to two-phase materials, organic/inorganic hybrids, and nanoparticle or polymer-based nanocomposites. Self-assembled nanostructures from more complex, multiscale and multiphase building blocks have been explored with limited success. Here, we demonstrate a ternary self-assembly approach using graphene as fundamental building blocks to construct metal oxide-graphene nanocomposites. A new class of layered nanocomposites is formed containing stable, ordered alternating layers of nanocrystalline metal oxides with graphene/graphene stacks. Alternatively, the graphene material can be incorporated into liquid-crystal-templated nanoporous structures to form high surface area, conductive networks. The self-assembly method can be also used to fabricate free standing, flexible metal oxide-graphene nanocomposite films and electrodes. We investigate the Li-ion insertion properties of the self-assembled electrodes for energy storage and show that the SnO2-graphene nanocomposite films can achieve near theoretical specific energy density without a significant charge/discharge degradation.

25 ENERGY STORAGE↗