Engineering Papers⌕ Search

Engineering topics

Liu, Jun

Publications and source records attributed to Liu, Jun.

At least 559 records · Page 31

Copolymer P(BS-co-LA) Enhanced Compatibility of PBS/PLA Composite

The copolymer P(BS-co-LA) with various block chains are synthesized and employed as the interface linker in poly(butyl succinate) (PBS)/polylactic acid (PLA) blends to enhance the compatibility of PBS and PLA. The crystallization and rheological properties are determined by various methods, as well as the mechanical properties. The results indicate that the addition of P(BS-co-LA) decreases the crystallization temperature and degree of crystallinity in the PBS/PLA composite. The P(BS-co-LA) with a long-block chain remarkably enhances the compatibility of PBS/PLA composites than short block chains, and the PBS/PLA/P(BS-hb-LA) composites show great elongation at break and impact strength. Besides, the crystallinity and the rate of crystallization are increased, which are also observed by the X-ray diffraction. All approaches lead to the same result that P(BS-co-LA) with the long block chain is an excellent compatibility agent to enhance mechanical properties of the PBS/PLA composites.

36 MATERIALS SCIENCE↗

Enabling High-Energy-Density Cathode for Lithium-Sulfur Batteries

High-loading sulfur electrode is critical for high energy Lithium-sulfur (Li-S) batteries used for practical applications. Unfortunately, dense and high-loading sulfur electrodes usually suffer from low sulfur utilization rate and limited cycle life. In this work, effects of electrode porosity on the electrode energy density, cell cycling stability, Li anode interface, and electrolyte/sulfur ratio were systematically investigated using high loading sulfur electrodes. The reduced electrode porosity increases volumetric energy density but also hinders electrode wetting process. To solve this problem, polysulfide (Li2S6) is selected as an electrolyte additive to enhance electrolyte penetration into dense sulfur cathodes. As a result, a high energy density of 1300 Wh L-1 (at electrode level) has been obtained for a dense sulfur cathode with a sulfur loading of 4 mg cm-2 at a compressed thickness of 60 µm. Li-S batteries with dense electrodes and Li2S6 additive also demonstrate promising cycling stability (~80 % capacity retention for 200 cycles). These significant improvements are contributed by synergistic effects of the dense sulfur cathode, improved electrolyte penetration, and suppressed growth of passivation layer on Li metal anode. This study sheds light on rational sulfur cathode structure design as well as control of electrode porosity for balanced energy density and cycling life.

Lu, Dongping↗

Near Surface Nucleation and Particle Mediated Growth of Colloidal Au Nanocrystals

During non-classical growth of nanostructures via assembly of primary nuclei, nucleation and assembly are assumed to be distinct processes: nanoparticles nucleate randomly and aggregate to form extended structures through Brownian motion in the presence of long-range attractive interactions. Here we investigate the relationship between these two processes by using in situ AFM, in situ, ex situ and cryo TEM and UV-Vis spectroscopy to observe growth of colloidal gold and simulations to develop a mechanistic model of the process. Our results reveal an inexorable link between nucleation and assembly with nuclei forming almost exclusively within a ~ 1 nm interfacial region of existing particles. The new particles immediately close the gap either through a diffusive jump or via growth of a neck between the seed and new particle, generating aggregates exhibiting features commonly attributed to oriented attachment of independently nucleated particles. The results demonstrate that creation of initial particle interfaces leads to local environments that redirect growth towards non-classical processes.

Cheng, Yingwen↗

Non-flammable electrolytes with high salt-to-solvent ratios for Li-ion and Li-metal batteries

Non-flammable electrolytes could intrinsically eliminate fire hazards and improve battery safety, but their compatibility with electrode materials, especially graphite anodes, remains an obstacle owing to the strong catalytic activity of the anode surfaces. Here, we report an approach that improves the stability of non-flammable phosphate electrolytes by adjusting the molar ratio of Li salt to solvent. At a high Li salt-to-solvent molar ratio (~1:2), the phosphate solvent molecules are mostly coordinated with the Li+ cations, and the undesired reactivity of the solvent molecules toward the graphite anode can be effectively suppressed. High cycling Coulombic efficiency (99.7%), good cycle life and safe operation of commercial 18650 Li-ion cells with these electrolytes are demonstrated. In addition, these non-flammable electrolytes show reduced reactivity toward Li-metal electrodes. Non-dendritic Li-metal plating and stripping in Li–Cu half-cells are demonstrated with high Coulombic efficiency (> 99%) and good stability.

Zeng, Ziqi↗

Stable cycling of high-voltage lithium metal batteries in ether electrolytes

The development of functional electrolytes that are stable with both the lithium (Li) anode and the 4-V cathode is of significant importance to enable long-term cycling stability of high-voltage Li metal batteries. Due to their limited oxidative stability (< 4 V), ethers have been excluded from being used in high-voltage batteries for a long time, in spite of their superior reductive stability against Li metal compared to the conventional organic carbonate electrolytes. Here we report a concentrated dual-salt/ether electrolyte design that can form stable interfacial layers on both the high-voltage LiNi1/3Mn1/3Co1/3O2 cathode and the Li metal anode, thus realizing an unprecedented capacity retention >90% over 300 cycles with a charge cut-off voltage of 4.3 V. This study offers a promising approach to enabling ether electrolytes for high-voltage applications, expanding a new spectrum of solvent choices for high-voltage Li metal batteries.

Ether electrolyte, high concentration, high voltag↗

Thin-Film Module Reverse-Bias Breakdown Sites Identified by Thermal Imaging: Preprint

Thin-film module sections are stressed under reverse bias to simulate partial shading conditions. Such stresses can cause permanent damage in the form of 'wormlike' defects due to thermal runaway. When large reverse biases with limited current are applied to the cells, dark lock-in thermography (DLIT) can detect where spatially-localized breakdown initiates before thermal runaway leads to permanent damage. Predicted breakdown defect sites have been identified in both CIGS and CdTe modules using DLIT. These defects include small pinholes, craters, or voids in the absorber layer of the film that lead to built-in areas of weakness where high current densities may cause thermal damage in a partial-shading event.

14 SOLAR ENERGY↗

Carbon coated hierarchical porous MoO2 nanoflowers as high-performance anodes in lithium-ion batteries

Highlights: • Carbon-coated hierarchical porous MoO{sub 2} are synthetized via a template-free solvothermal technique. • Synthesizing hybrid porous materials provides potential to achieve superior performance in energy application. • This hierarchical structure can be extended to design for other materials in view of their application in LIBs. - Abstract: Carbon-coated hierarchical porous MoO{sub 2} nanoflowers are synthetized via a template-free solvothermal technique and investigated as anodes in lithium-ion batteries (LIBs). Such hybrid porous materials possess high porosity and a conductive layer, which have superior lithium ion/electron transport. The voids inside the structure can accommodate huge volume expansion and relieve the stress. The relative MoO{sub 2} electrodes present a high reversible capacity of 784.7 mA h g {sup −1} after 60 cycles (707.7 mA h g{sup −1} after 120 cycles for 200 mA g{sup −1}) and high coulumbic efficiency (above 98% over 120 cycles). Our study can easily be extended to other materials with a similar hierarchical structure in view of their application in LIBs.

30 DIRECT ENERGY CONVERSION↗

ZnCr-LDH/N-doped graphitic carbon-incorporated g-C3N4 2D/2D nanosheet heterojunction with enhanced charge transfer for photocatalysis

Highlights: • Synthesize a novel ZnCr-LDH/modified-g-C{sub 3}N{sub 4} photocatalyst by a facile template free in situ coprecipitation method approach. • The synergistic effect of adsorption and catalytic improve the ability of photodegradation. • Composites with 2D-2D nanosheets structure present superior catalytic activity than pure phases. • Calcinated photocatalyst has high visible-light respond capacity and low recombination rate of electron-hole pairs due to the formation of heterojunction. - Abstract: In this work, we successfully synthesized a novel ZnCr-LDH/N-doped graphitic carbon-incorporated g-C{sub 3}N{sub 4} (g-C{sub 3}N{sub 4}-C(N)) hybrid with unique two-dimensional/two-dimensional (2D-2D) structure for the efficient degradation of Congo red under visible light irradiation. It was demonstrated that ZnCr-LDH/g-C{sub 3}N{sub 4}-C(N) exhibited lower photogenerated electron-hole recombination rate and enhanced light harvesting. Furthermore, its derived calcined product also showed outstanding performance due to the unique heterogeneous structure and the synergistic effect between photocatalysis and adsorption. In addition, the mixed metal oxide ZnO and ZnCr{sub 2}O{sub 4} in ZnCr-CLDH/g-C{sub 3}N{sub 4}-C(N) dispersed uniformly on the g-C{sub 3}N{sub 4}-C(N) exposed more active sites and facilitated the photodegradation of pollutants.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fuel consumption for various driving styles in conventional and hybrid electric vehicles: Integrating driving cycle predictions with fuel consumption optimization

Here, improving fuel economy and lowering emissions are key societal goals. Standard driving cycles, pre-designed by the US Environmental Protection Agency (EPA), have long been used to estimate vehicle fuel economy in laboratory-controlled conditions. They have also been used to test and tune different energy management strategies for hybrid electric vehicles (HEVs). This paper aims to estimate fuel consumption for a conventional vehicle and a HEV using personalized driving cycles extracted from real-world data to study the effects of different driving styles and vehicle types on fuel consumption when compared to the estimates based on standard driving cycles. To do this, we extracted driving cycles for conventional vehicles and HEVs from a large-scale U.S. survey that contains real-world GPS-based driving records. Next, the driving cycles were assigned to one of three categories: volatile, normal, or calm. Then, the driving cycles were used along with a driver-vehicle simulation that captures driver decisions (vehicle speed during a trip), powertrain, and vehicle dynamics to estimate fuel consumption for conventional vehicles and HEVs with power-split powertrain. To further optimize fuel consumption for HEVs, the Equivalent Consumption Minimization Strategy (ECMS) is applied. The results show that depending on the driving style and the driving scenario, conventional vehicle fuel consumption can vary widely compared with standard EPA driving cycles. Specifically, conventional vehicle fuel consumption was 13% lower in calm urban driving, but almost 34% higher for volatile highway driving compared with standard EPA driving cycles. Interestingly, when a driving cycle is predicted based on the application of case-based reasoning and used to tune the power distribution in a hybrid electric vehicle, its fuel consumption can be reduced by up to 12% in urban driving. Implications and limitations of the findings are discussed.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Minimizing Polysulfide Shuttle Effect in Lithium-Ion Sulfur Batteries by Anode Surface Passivation

Lithium-ion sulfur batteries use non-metal materials as the anode to address safety concerns associated with lithium metal anode. However, polysulfide shuttle reactions still occur on the non-metal anode (such as graphite and Si), and result in limited battery efficiency. In this work, we used Al2O3 layers coated by atomic layer deposition (ALD) technique to suppress the shuttle reactions. With the optimal thickness of 2 nm Al2O3 coated on graphite anode, the Coulombic efficiency of the sulfur cathode was improved from 84% to 96% in the first cycle, and from 94% to 97% in the subsequent cycles. As a result, the discharge capacity of the sulfur cathode was increased to 550 mAh g-1 in the 100th cycle, as compared with 440 mAh g-1 when the pristine graphite anode was used. The Al2O3 passivation layer minimizes the formation of insoluble polysulfide (Li2S2, Li2S) on the surface of graphite anode and improves the efficiency and capacity retention of the graphite-sulfur batteries. The surface passivation strategy could also be used in other Li sulfur battery systems (with Li, Si, and Sn anodes), to minimize side reactions and enable high-performance and safe sulfur batteries.

Liu, Jian↗

Thin-Film Module Reverse-Bias Breakdown Sites Identified by Thermal Imaging

Thin-film module sections are stressed under reverse bias to simulate partial shading conditions. Such stresses can cause permanent damage in the form of 'wormlike' defects due to thermal runaway. When large reverse biases with limited current are applied to the cells, dark lock-in thermography (DLIT) can detect where spatially-localized breakdown initiates before thermal runaway leads to permanent damage. Predicted breakdown defect sites have been identified in both CIGS and CdTe modules using DLIT. These defects include small pinholes, craters, or voids in the absorber layer of the film that lead to built-in areas of weakness where high current densities may cause thermal damage in a partial-shading event.

14 SOLAR ENERGY↗

A biomimetic high-capacity phenazine-based anolyte for aqueous organic redox flow batteries

Redox flow batteries (RFB) for use as a stationary energy storage system require redox-active materials with high capacity, stability, and sustainability. Aqueous soluble organic (ASO) redox-active materials have recently attracted significant attention as alternatives to traditional transition metal ions. However, reported reversible capacities are substantially lower than their theoretical values based on solubility. In this paper, we describe a phenazine-based ASO compound with an exceptionally high reversible capacity that exceeds 90% of its theoretical solubility value. In our combined nuclear magnetic resonance (NMR) and density functional theory (DFT) study, we discovered that by strategically modifying the phenazine molecular structure, preferential solvation is enabled, thereby increasing the solubility of the phenazine from near-zero to as much as 1.8 M, while its redox potential can be shifted by more than 400 mV. An RFB based on the highly alkaline-soluble and two-electron transfer phenazine derivative, 7,8-dihydroxyphenazine-2-sulfonic acid exhibits an operating voltage at 1.4 V and capacity retention of 99.98% per cycle over 500 cycles at a reversible capability of 67 Ah L-1. Development of this phenazine compound represents a new approach for realizing energy-dense, cost-effective ASO flow batteries for stationary energy storage applications.

Hollas, Aaron↗

High-voltage lithium-metal batteries enabled by localized high-concentration electrolytes

Lithium metal batteries face safety and low Coulombic Efficiency barriers. Superconcentrated electrolyte is stable with lithium metal but exhibits high cost and poor wettability. We report a localized superconcentrated electrolyte by diluting a superconcentrated electrolyte with an ‘inert’ diluent which does not dissolve the salt but miscible with the solvent used in the superconcentrated electrolyte. This electrolyte exhibits low cost, good wettability, and enables dendrite-free lithium cycling with high Coulombic Efficiency (99.3%) and stability (> 95% capacity retention after 300 cycles) of lithium||LiNixMnyCozO2 batteries. The concept of localized superconcentrated electrolyte can also be applied to other multi-functional electrolytes for broad applications.

Coulomic efficiency, anode, batteries↗

Discrimination of Medicine Radix Astragali from Different Geographic Origins Using Multiple Spectroscopies Combined with Data Fusion Methods

Raman spectra and ultraviolet–visible absorption spectra of four different geographic origins of Radix Astragali were collected. These data were analyzed using kernel principal component analysis combined with sparse representation classification. The results showed that the recognition rate reached 70.44% using Raman spectra for data input and 90.34% using ultraviolet–visible absorption spectra for data input. A new fusion method based on Raman combined with ultraviolet–visible data was investigated and the recognition rate was increased to 96.43%. The experimental results suggested that the proposed data fusion method effectively improved the utilization rate of the original data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrolyte for stable cycling of high-energy lithium sulfur redox flow batteries

A device comprising: a lithium sulfur redox flow battery comprising an electrolyte composition comprising: (i) a dissolved Li 2 S x electroactive salt, wherein x.gtoreq.4; (ii) a solvent selected from dimethyl sulfoxide, tetrahydrofuran, or a mixture thereof; and (iii) a supporting salt at a concentration of at least 2 M, as measured by moles of supporting salt divided by the volume of the solvent without considering the volume change of the electrolyte after dissolving the supporting salt.

25 ENERGY STORAGE↗

25 Mg NMR and Computational Modeling Studies of the Solvation Structures and Molecular Dynamics in Magnesium Based Liquid Electrolytes

There is increasing evidence that the solvation structure of the active components in a liquid electrolyte solution strongly impacts the performance in electrochemical applications. In this work, the nanoscale solvation structures and dynamics of Mg(BH 4 ) 2 and Mg(TFSI) 2 dissolved in diglyme (DGM) at various concentrations and ratios of Mg(BH 4 ) 2 /Mg(TFSI) 2 were investigated using a combination of natural abundance 25 Mg NMR, quantum chemistry calculations of 25 Mg NMR chemical shifts, classical molecular dynamics (MD) calculations, and electrochemical performance tests. By mixing two competing Mg salts, we were able to reduce the strong covalent interactions between Mg 2+ and BH 4 – anions. A small increase is observed in the coordination number of Mg-TFSI and a significant increase in the interaction of Mg 2+ ions with glymes. Through a combination of NMR, DFT and MD simulations, various stable species around 1 nm in size were detected in the mixed salt solution, which play key roles in the enhanced electrochemical performance of the mixed electrolyte. It is established that for the neat Mg(TFSI) 2 in DGM electrolyte at dilute concentrations the TFSI - is fully dissociated from Mg 2+ . At higher concentrations, Mg 2+ and TFSI - are only partially dissociated as contact ion pairs are formed. In contrast, at 0.01 M Mg(BH 4 ) 2 (saturated concentration) in DGM, the first solvation shell of a Mg 2+ ion contains two BH 4 - anions and one DGM molecule, while the second solvation shell consists of five to six DGM molecules. An exchange mechanism between the solvation structures in the combined electrolyte containing both Mg(BH 4 ) 2 and Mg(TFSI) 2 in DGM was found to result in the observation of a single 25 Mg NMR peak. This exchange is responsible for an increase in uncoordinated anions, as well as improved stability and ionic conductivity as compared to single anion solution. Solvent molecule rearrangement and direct Mg-ion exchange between the basic solvation structures are hypothesized as likely reasons for the exchange. We elucidate that the solvent rearrangement is energetically much more favorable than direct Mg-ion hopping and is thus suggested as the dominant exchange mechanism.

Magnesium battery, electrolytes, Mg(BH4)2, Mg(TFSI↗

Polymer-sulfur composite materials for electrodes in Li-S energy storage devices

Composite materials containing sulfurized polymers and sulfur-containing particles can be used in lithium-sulfur energy storage devices as a positive electrode. The composite material exhibits relatively high capacity retention and high charge/discharge cycle stability. In one particular instance, the composite comprises a sulfurized polymer having chains that are cross-linked through sulfur bonds. The polymer provides a matrix in which sulfide and/or polysulfide intermediates formed during electrochemical charge-discharge processes of sulfur can be confined through chemical bonds and not mere physical confinement or sorption.

Liu, Jun↗

Addressing Passivation in Lithium-Sulfur Battery Under Lean Electrolyte Condition

Reducing the electrolyte amount is critical for high practical specific energy of Li-S batteries. The lean electrolyte condition raises a complex situation for sulfur redox reactions since they rely on the electrolyte mediation. The insulating nature of discharge product Li 2 S and its uncontrollable accumulation (passivation) at the cathode interface is one of the major challenges for stable cycling of a Li-S battery under lean electrolyte condition. Here, we present that the NH 4 TFSI additive in electrolyte solution greatly alleviates the passivation issue in Li-S batteries under lean electrolyte condition. The ammonium additive enhances the solvation between sulfide anion and NH 4 + cation, and greatly reduces the amount of large insoluble and insulting Li 2 S particles in the sulfur cathodes, which greatly facilitates the reversible and sustainable redox reactions of sulfur. Therefore, the cycle life of Li-S battery under lean electrolyte condition was greatly improved. In addition, we found that the morphology of Li anode is dependent on the cathode structures. Ammonium additive enables a homogeneous surface of cathode and Li anode and extended cycle life.

Pan, Huilin↗