Engineering Papers⌕ Search

Engineering topics

Lilley, D. G.

Publications and source records attributed to Lilley, D. G..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Swirl flow turbulence modeling

Confined turbulent swirling flow data obtained from a single hot-wire using a six-orientation technique are analyzed numerically. The effects of swirl strength and the presence of a strong contraction nozzle further downstream on deduced parameters is also presented and discussed for the case of chamber-to-inlet diameter ratio D/d = 2. Three swirl strengths are considered with inlet swirl vane angles of 0, 45 and 70 deg. A strong contraction nozzle with an area ratio of 4 is located two chamber-diameters downstream of the inlet to the flowfield. It is found that both the swirl strength and the contraction have strong effects on the turbulence parameters. Generally, the most dramatic effect of increase of swirl strength is the considerable increase in values of all the parameters considered, (rx-viscosity, kinetic energy of turbulence, length scales, and degree of nonisotropy). The presence of a strong contraction nozzle tends to increase the turbulence parameter values in regions of acceleration and to reduce them in deceleration regions. Based on similarity of viscosity and length scale profiles, a C sub mu formulation is deduced which is shown to improve the predictive capability of the standard k-epsilon turbulence model in swirling recirculating flows.

Abujelala, M. T.↗
NASA NTRS1984

Swirl, confinement and nozzle effects on confined turbulent flow

Predictions of swirl, confinement and nozzle effects on confined turbulent flow are exhibited and compared with five-hole pitot-probe time-mean velocity measurements. Two sets of computations are given, one using the standard k-epsilon turbulence model and the other using a C sub mu formulation model deduced from recent six-orientation single-wire hot-wire measurements. Results confirm that the accuracy of the latter model is superior. To highlight the effects of confinement and exit nozzle area on this flow, three expansion ratios and two contraction ratios are used. Predictions are given for a full range of swirl strengths using measured inlet conditions for axial, radial and swirl velocity profiles. The predicted velocity profiles illustrate the large-scale effects of inlet swirl on flowfields. It appears that a strong contraction nozzle has a pronounced effect, on swirl flow cases, with discouragement of central recirculation zones, and forward flow in highly swirled vortex core regions. The expansion ratio value has large-scale effects on the size and location of the recirculation zones.

Abujelala, M. T.↗
NASA NTRS1984

Turbulence measurements in a complex flowfield using a crossed hot-wire

An X-wire probe was used to measure the time-mean and fluctuating velocities and shear stress in nonswirling nonreacting confined jet flows. Data were taken from an axisymmetric confined jet with an expansion ratio of 2 and an expansion angle of 90 deg, and from the same segment with a contraction nozzle. Velocity profiles developed faster in the confined jet than in the free jet, with the former experiencing higher turbulence levels and larger time-mean velocities. The X-wire is concluded to furnish more accurate results for the turbulent shear stress than a multioriented single-wire technique.

Lilley, D. G.↗
NASA NTRS1984

Five-hole pitot probe measurements of swirl, confinement and nozzle effects on confined turbulent flow

The results of a time-mean flow characterization of nonswirling and swirling inert flows in a combustor are reported. The five-hole pitot probe technique was used in axisymmetric test sections with expansion ratios of 1 and 1.5. A prominent corner recirculation zone identified in nonswirling expanding flows decreased in size with swirling flows. The presence of a downstream nozzle led to an adverse pressure gradient at the wall and a favorable gradient near the centerline. Reducing the expansion ratio reduced the central recirculation length. No significant effect was introduced in the flowfield by a gradual expansion.

Lilley, D. G.↗
NASA NTRS1984

Investigations of flowfields found in typical combustor geometries

Studies are concerned with experimental and theoretical research on 2-D axisymmetric geometries under low speed, nonreacting, turbulent, swirling flow conditions. The flow enters the test section and proceeds into a larger chamber (the linear expansion ratio D/d = 2, 1.5 and 1) via a sudden or gradual expansion (side wall angle alpha = 90 and 45 degrees). A weak or strong nozzle (of area ratio A/a = 2 and 4) may be positioned downstream at x/D = 2 to form a contraction exit to the test section. Inlet swirl vanes are adjustable to a variety of vane angles with values of theta = 0, 38, 45, 60 and 70 degrees being emphasized. The objective is to determine the effect of these parameters on isothermal flow field patterns, time mean velocities and turbulence quantities, and to establish an improved simulation in the form of a computer prediction code equipped with a suitable turbulence model. The goal of the on going research is to perform experiments and complementary computations with the idea of doing the necessary type of research that will yield improved calculation capability. This involves performing experiments where time mean turbulence quantities are measured and taking input conditions and running an existing prediction code for a variety of test cases so as to compare predictions against experiment.

Lilley, D. G.↗
NASA NTRS1984

Accuracy and directional sensitivity of the single-wire technique

Multi-orientation of a single-hot-wire is a novel way to measure the three time-mean velocities, the three turbulent normal stresses, and the three turbulent shear stresses. The present study focuses on the accuracy and directional sensitivity of the technique with respect to mean flow velocity orientation to the probe. Results demonstrate relative insensitivity, indicating that the method is a useful cost-effective tool for turbulent flows of unknown dominant flow direction.

Lilley, D. G.↗
NASA NTRS1984

Limitations and empirical extensions of the k-epsilon model as applied to turbulent confined swirling flows

Shortcomings and recommended corrections to the standard two-equation k-epsilon turbulence model suggested by previous investigators are presented. They are assessed regarding their applicability to turbulent swirling recirculating flow. Recent experimental data on swirling confined flows, obtained with a five-hole pitot probe and a six-orientation hot-wire probe, are used to obtain optimum values of the turbulence parameters C-mu, C2, and sigma-epsilon for swirling flows. General predictions of moderately and strongly swirling flows with these values are more accurate than predictions with the standard or previous simple extensions of the k-epsilon turbulence model.

Lilley, D. G.↗
NASA NTRS1983

Single-wire swirl flow turbulence measurements

A six-orientation, single wire hot wire technique is used to investigate nonswirling and swirling nonreacting flow in an axisymmetric test section with expansion ratio (test section/inlet nozzle diameter) = 2, which may be equipped with a strong contraction nozzle of area ratio 4 at a contraction nozzle downstream distance/test section diameter value = 2. The flowfield contains corner and central recirculation zones typical of gas turbine and ramjet combustion chambers. Swirl may be imparted to the incoming flow by means of a variable angle vane swirler. The effect of swirl on time mean velocities and complete Reynolds stress tensor is investigated, and extensive results are given for swirl vane angles of zero (swirler removed), 38, 45, 60 and 70 deg. The data are being used to aid in the evolution of turbulence models for these complex flow situations. A directional sensitivity analysis is included, which determines the relative accuracy of the measurement technique to approach velocity orientation.

Lilley, D. G.↗
NASA NTRS1983

The performance of an annular vane swirler

In connection with the desirability of optimizing the design of a gas turbine combustion chamber, there exists a need for a more complete understanding of the fluid dynamics of the flow in such chambers. In order to satisfy this need, experimental and theoretical research is being conducted with the objective to study two-dimensional axisymmetric geometries under low speed, nonreacting, turbulent, swirling flow conditions. The flow enters the test section and proceeds into a larger chamber. Inlet swirl vanes are adjustable to a variety of vane angles. The present investigation concentrates on the time-mean flow characteristics which are generated by the upstream annular swirler. The investigation makes use of a five-hole pitot probe technique. A theoretical analysis of swirl numbers associated with several idealized exit velocity profiles is included, and values of the ratio of maximum swirl velocity to maximum axial velocity at different swirl strengths are given for each case.

Lilley, D. G.↗
NASA NTRS1983

Turbulent Combustor Flowfield Investigation

The 2-D axisymmetric geometries under low speed, nonreacting, turbulent, swirling flow conditions were investigated. The effect of the parameters on isothermal flowfield patterns, time mean velocities and turbulence quantities is determined and an improved simulation in the form of a computer prediction code equipped with a suitable turbulence model is established. This is a prerequisite to the prediction of more complex turbulent reacting flows.

Lilley, D. G.↗
NASA NTRS1983

Five-hole pitot probe time-mean velocity measurements in confined swirling flows

Nonswirling and swirling nonreacting flows in an axisymmetric test section with an expansion ratio D/d = 2, which may be equipped with contraction nozzles of area ratios 2 and 4, are investigated. The effects of a number of geometric parameters on the flow-field are investigated, among them side-wall expansion angles of 90 and 45 deg, swirl vane angles of 0, 38, 45, 60, and 70 deg, and contraction nozzle locations L/D = 1 and 2 (if present). Data are acquired by means of a five-hole pitot probe enabling three time-mean velocity components in the axial, radial, and azimuthal directions to be measured. The velocities are extensively plotted and artistic impressions of recirculation zones are set forth. The presence of a swirler is found to shorten the corner recirculation zone and to generate a central recirculation zone followed by a precessing vortex core. A gradual inlet expansion has the effect of encouraging the flow to remain close to the sidewall and shortening the extent of the corner recirculation zone in all cases investigated.

Yoon, H. K.↗
NASA NTRS1983

Confined swirling flow predictions

The validity of flowfield predictions resulting from the choice of inlet velocity profiles is assessed. Results demonstrate that realistic predictions are forthcoming only from the inclusion of realistic axial, radial and swirl velocity profiles as inlet conditions. Predictions are then exhibited for a range of swirl strengths phi = 0, 38, 45, 60 and 70 degrees using measured inlet axial, radial and swirl velocity profiles in each case. Downstream nozzle effects (two blockage size at two axial locations) are included. The ensuing flowfields are characterized via velocity profiles and streamline patterns, and illustrate the large-scale effects of inlet swirl and outlet nozzles on flowfields.

Abujelala, M. T.↗
NASA NTRS1982

Flow aerodynamics modeling of an MHD swirl combustor - Calculations and experimental verification

This paper describes a computer code for calculating the flow dynamics of constant density flow in the second stage trumpet shaped nozzle section of a two stage MHD swirl combustor for application to a disk generator. The primitive pressure-velocity variable, finite difference computer code has been developed to allow the computation of inert nonreacting turbulent swirling flows in an axisymmetric MHD model swirl combustor. The method and program involve a staggered grid system for axial and radial velocities, and a line relaxation technique for efficient solution of the equations. Turbulence simulation is by way of a two-equation Kappa-epsilon model. The code produces as output the flowfield map of the nondimensional stream function, axial, and swirl velocity. Good agreement was obtained between the theoretical predictions and the qualitative experimental results. The best seed injector location for uniform seed distribution at combustor exit is with injector located centrally on the combustor axis at entrance to the second stage combustor.

Gupta, A. K.↗
NASA NTRS1982

Investigations of flowfields found in typical combustor geometries

Experimental and theoretical research undertaken on 2-D axisymmetric geometries under low speed, nonreacting, turbulent, swirling flow conditions is reported. The flow enters the test section and proceeds into a larger chamber (the expansion ratio D/d = 2) via a sudden or gradual expansion (sidewall angle alpha = 90 and 45 degrees). Inlet swirl vanes are adjustable to a variety of vane angles with values of phi = 0, 38, 45, 60 and 70 degrees being emphasized.

Lilley, D. G.↗
NASA NTRS1982

Research on the noise produced by large scale structure in supersonic jets

Using a dual electrode glow discharge excitation device, a method of mode selection into either the n = 0 or n = + or - 1 azimuthal modes was developed and tested by Fourier analyzing experimental azimuthal phase and amplitude data. On a M = 2.1 moderate Reynolds number (Re = 68,000) jet with a laminar boundary layer, under n = 0 or n = +1 excitation, coherent axial wave evolution, mean flow, and sound pressure level directivity measurements were performed. The boundary layer of this same jet was excited usng a grit coating on the nozzle wall, and bandpassed axial wave evolution data obtained and compared to the masurements made by previous workers on a conventional high Reynolds number jet (Re = 5,000,000) using a hot-film type probe.

Mclaughlin, D. K.↗