Engineering Papers⌕ Search

Engineering topics

Liang, Chengdu

Publications and source records attributed to Liang, Chengdu.

At least 73 records · Page 4

Lithium sulfide compositions for battery electrolyte and battery electrode coatings

Methods of forming lithium-containing electrolytes are provided using wet chemical synthesis. In some examples, the lithium containing electroytes are composed of .beta.-Li.sub.3PS.sub.4 or Li.sub.4P.sub.2S.sub.7. The solid electrolyte may be a core shell material. In one embodiment, the core shell material includes a core of lithium sulfide (Li.sub.2S), a first shell of .beta.-Li.sub.3PS.sub.4 or Li.sub.4P.sub.2S.sub.7, and a second shell including one or .beta.-Li.sub.3PS.sub.4 or Li.sub.4P.sub.2S.sub.7 and carbon. The lithium containing electrolytes may be incorporated into wet cell batteries or solid state batteries.

25 ENERGY STORAGE↗

In-situ observation of inhomogeneous degradation in large format Li-ion cells by neutron diffraction

This work presents a non-destructive in-situ method for probing degradation mechanisms in large format, operating, commercial lithium-ion batteries by neutron diffraction. A fresh battery (15 Ah capacity) was shown to have a uniform (homogeneous) local state of charge (SOC) at 4.0 V (9 Ah SOC) and 4.2 V (15 Ah SOC), with 1.33 C and 2.67 C charging rates, respectively. This battery was then aggressively cycled until it retained only a 9 Ah capacity, 60% of its original value. Inhomogeneous deterioration in the battery was observed: near the edges, both the graphite anode and the spinel-based cathode showed a significant loss of capacity, while near the central area, both electrodes functioned properly. An SOC mapping measurement of the degraded battery in the fully charged state (4.2 V) indicated that the loss of local capacity of the anode and cathode is coupled.

25 ENERGY STORAGE↗

Unraveling structural evolution of LiNi 0.5 Mn 1.5 O 4 by in situ neutron diffraction

Here, we report that the electrochemical properties of the spinel LiNi 0.5 Mn 1.5 O 4 cathode material are influenced by the synthesis processes, which determines the impurity phase and the distribution of Ni and Mn in the spinel structure. Taking advantage of neutron's high sensitivity to Ni and Mn, in situ neutron diffraction has been employed to quantify the phase formation/structural evolution process under continuous heating/cooling and isothermal annealing conditions. The results show that the subtle Ni and Mn ordering process occurs slowly at 700 °C and the degree of ordering can be controlled by the annealing time. At temperatures above 750 °C, the LiNi 0.5 Mn 1.5 O 4 spinel phase starts to decompose into the rock-salt impurity phase accompanied by the release of O 2 . The rock-salt phase reverts back to the spinel phase upon cooling along with the oxygen uptake. In conclusion, the dynamic process of structural evolution of LiNi 0.5 Mn 1.5 O 4 that was unraveled by in situ neutron diffraction is valuable for guiding the synthesis of cathode materials with desirable properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Artificial SEI Enables the Use of A LiNi0.5Mn1.5O4 5 V Cathode with Conventional Electrolytes

LiNi0.5Mn1.5O4 spinel is considered one of the most promising cathodes for advanced lithium ion batteries. However, the operation potential of LiNi0.5Mn1.5O4, ~4.75 V, is beyond the high voltage limit of the state-of-art electrolyte, ~4.3 V. Here, using thin films of LiNi0.5Mn1.5O4 as a model material, we show evidence that an artificial solid electrolyte interphase (SEI) enables the use of this 5 V cathode with conventional carbonate electrolytes. A thin coating of Lipon (lithium phosphorus oxynitride) as an artificial SEI on LiNi0.5Mn1.5O4 could remedy the decomposition of the electrolyte. The thickness of the Lipon artificial SEI is optimized by balancing the protection and additional resistance. The strategy of artificial SEI on cathodes is expected to enable the wide application of other high voltage cathodes for lithium ion batteries.

artificial SEI↗

Lithium Polysulfidophosphates: A Family of Lithium-Conducting Sulfur-Rich Compounds for Lithium-Sulfur Batteries

Given the great potential for improving the energy density of state-of-the-art lithium-ion batteries by a factor of 5, a breakthrough in lithium-sulfur (Li-S) batteries will have a dramatic impact in a broad scope of energy related fields. Conventional Li-S batteries that use liquid electrolytes are intrinsically short-lived with low energy efficiency. The challenges stem from the poor electronic and ionic conductivities of elemental sulfur and its discharge products. We report herein lithium polysulfidophosphates (LPSP), a family of sulfur-rich compounds, as the enabler of long-lasting and energy-efficient Li-S batteries. LPSP have ionic conductivities of 3.0 10-5 S cm-1 at 25 oC, which is 8 orders of magnitude higher than that of Li2S (~10-13 S cm-1). The high Li-ion conductivity of LPSP is the salient characteristic of these compounds that impart the excellent cycling performance to Li-S batteries. In addition, the batteries are configured in an all-solid state that promises the safe cycling of high-energy batteries with metallic lithium anodes.

batteries↗

Anomalous high ionic conductivity of nanoporous -Li3PS4

Lithium-ion conducting solid electrolytes hold the promise for enabling high-energy battery chemistries and circumventing safety issues of conventional lithium batteries1-3. Achieving the combination of high ionic conductivity and broad electrochemical window in solid electrolytes is a grand challenge for the synthesis of battery materials. Herein we show an enhancement of room-temperature lithium-ion conductivity of 3 orders of magnitude by creating nanostructured Li3PS4. This material has a wide (5V) electrochemical window and superior chemical stability against lithium metal. The nanoporous structure of Li3PS4 reconciles two vital effects that enhance ionic conductivity: (1) The reduced dimension to nanometer-sized framework stabilizes the high conduction beta phase that occurs at elevated temperatures1,4; and (2) The high surface-to-bulk ratio of nanoporous -Li3PS4 promotes surface conduction5,6. Manipulating the ionic conductivity of solid electrolytes has far-reaching implications for materials design and synthesis in a broad range of applications such as batteries, fuel-cells, sensors, photovoltaic systems, and so forth3,7.

batteries↗

A perspective on coatings to stabilize high-voltage cathodes: LiMn1.5Ni0.5O4 with subnanometer Lipon cycled with LiPF6 electrolyte

High voltage Li-ion cathodes push the limits of stability for both cathode and electrolyte. Here subnanometer coatings of an amorphous thin film electrolyte (Lipon) improved the room temperature and 60 C cycling stability of a LiMn1.5Ni0.5O4 spinel cathode when charged to 4.9V with a standard LiPF6 carbonate electrolyte. The cathodes delivered superior C-rate performances up to a 5C discharge, when compared to the uncoated cathodes. Enhanced performance extended for at least 100 cycles. Electrochemical impedance spectroscopy indicates that Lipon slows the increase of interface resistance. Thicker 1-3nm Lipon coatings are sufficiently insulating as to block electronic transport to the cathode particles. Thick coatings also slow Mn dissolution. Results suggest that Lipon may act to scavenge impurities or block active sites that promote electrolyte decomposition. While greatly improved by the Lipon coating, this cathode is not sufficiently stable for long cycle life applications. Further work is needed to assess if and what surface coatings will ultimately stabilize the high voltage cathodes. Comments include insight from other studies of Lipon coated cathodes and directions for future research.

Li-ion battery↗

A Lithium Superionic Sulfide Cathode for Lithium-Sulfur Batteries

This work presents a facile synthesis approach for core-shell structured Li2S nanoparticles, which have Li2S as the core and Li3PS4 as the shell. This material functions as lithium superionic sulfide (LSS) cathode for long-lasting, energy-efficient lithium-sulfur (Li-S) batteries. The LSS has an ionic conductivity of 10-7 S cm-1 at 25 oC, which is 6 orders of magnitude higher than that of bulk Li2S (~10-13 S cm-1). The high lithium-ion conductivity of LSS imparts an excellent cycling performance to all-solid Li-S batteries, which also promises safe cycling of high-energy batteries with metallic lithium anodes.

batteries↗

Visualizing the chemistry and structure dynamics in lithium-ion batteries by in-situ neutron diffraction

We report an in-situ neutron diffraction study of a large format pouch battery cell. The succession of Li-Graphite intercalation phases was fully captured under an 1C charge-discharge condition (i.e., charge to full capacity in 1 hour). However, the lithiation and dilithiation pathways are distinctively different and, unlike in slowing charging experiments with which the Li-Graphite phase diagram was established, no LiC24 phase was found during charge at 1C rate. Approximately 75 mol. % of the graphite converts to LiC6 at full charge, and a lattice dilation as large as 4% was observed during a charge-discharge cycle. Our work demonstrates the potential of in-situ, time and spatially resolved neutron diffraction study of the dynamic chemical and structural changes in “real-world” batteries under realistic cycling conditions, which should provide microscopic insights on degradation and the important role of diffusion kinetics in energy storage materials.

25 ENERGY STORAGE↗

Vacuum-tight sample transfer stage for a scanning electron microscopic study of stabilized lithium metal particles

To facilitate construction analysis, failure analysis, and research in lithium ion battery technology, a high quality methodology for battery disassembly is needed. This paper presents a methodology for battery disassembly that considers key factors based on the nature and purpose of post-disassembly analysis. The methodology involves upfront consideration of analysis paths that will be conducted on the exposed internal components to preserve the state (operational or failed) of the battery. The disassembly processes and exposures must not alter the battery materials once they are removed from their hermetically sealed containers. Because the process of battery disassembly can involve exposure to potentially hazardous compounds or lead to thermal run-away, a brief review concerning the safety hazards of disassembly is also given.

25 ENERGY STORAGE↗

Phosphorous pentasulfide as a novel additive for high-performance lithium-sulfur batteries

Lithium-sulfur (Li-S) batteries suffer from rapid capacity decay and low energy efficiency because of the low solubility of lithium sulfide (Li2S) in organic solvents and the intrinsic polysulfide shuttle phenomenon. Here, we report a novel additive of phosphorus pentasulfide (P2S5) in organic electrolyte to boost the cycling performance of Li-S batteries. The function of the additive is two-fold: (1) P2S5 promotes the dissolution of Li2S and alleviates the loss of capacity caused by the precipitation of Li2S; and (2) P2S5 passivates the surface of lithium metal and therefore eliminates the polysulfide shuttle phenomenon. A Li-S test cell demonstrates high reversible capacity of 900-1350 mAh g-1 and high coulombic efficiency of 90% for 40 stable cycles at 0.1 C.

Lin, Zhan↗

Low-temperature exfoliation of multilayer-graphene material from FeCl 3 and CH 3 NO 2 co-intercalated graphite compound

Graphene materials derived through the exfoliation of graphite are always accompanied with high population of defects and/or surface functionalities due to the harsh conditions utilized in the synthesis. We describe herein a scalable approach for the preparation of high quality graphene materials via low-temperature exfoliation of graphite under mild chemical conditions. The microwave induced rapid decomposition of nitromethane at low temperature produces mechanical force that lifts up the graphene sheets from the FeCl 3 and CH 3 NO 2 co-intercalated graphite compound without creating defects and functional groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗