Engineering Papers⌕ Search

Engineering topics

Li, Xiang

Publications and source records attributed to Li, Xiang.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Silicon Anodes with Improved Calendar Life Enabled By Multivalent Additives

Silicon is widely recognized as the most promising upgrade for graphite anodes due to its much higher capacity, natural abundance, and ability to be directly applied in the slurry-based, roll-to-roll production lines. However, in addition to the fast capacity decay, silicon anodes also suffer from inferior calendar life in practical applications due to the unstable solid-electrode interface (SEI). Until now, strategies to effectively improve the calendar life by tailored SEIs remain largely unclear, especially in high-Si content, zero-graphite anodes. Here, silicon anodes with superior calendar life are developed by adding small concentrations of multivalent salts into the baseline electrolyte. The Ca additive reacts with the F ions in the electrolyte, forming a layer of nanocrystalline CaF 2 that is closely coated around the silicon particles. The CaF 2 -enabled new SEI is strong and dense, which effectively protects the silicon core from side reactions, leading to lower capacity decay after calendar aging at high voltage. More importantly, the Ca additive is effective universally for all available commercial silicon or SiO sources. This study provides a feasible and low-cost solution for developing silicon anodes with long calendar life, paving the way towards commercially viable silicon anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Electronic nature of chiral charge order in the kagome superconductor CsV 3 Sb 5

Kagome superconductors with T C up to 7 K have been discovered for over 40 y. Recently, unconventional chiral charge order has been reported in kagome superconductor KV 3 Sb 5 , with an ordering temperature of one order of magnitude higher than the T C . However, the chirality of the charge order has not been reported in the cousin kagome superconductor CsV 3 Sb 5 , and the electronic nature of the chirality remains elusive. In this paper, we report the observation of electronic chiral charge order in CsV 3 Sb 5 via scanning tunneling microscopy (STM). We observe a 2 × 2 charge modulation and a 1 × 4 superlattice in both topographic data and tunneling spectroscopy. 2 × 2 charge modulation is highly anticipated as a charge order by fundamental kagome lattice models at van Hove filling, and is shown to exhibit intrinsic chirality. We find that the 1 × 4 superlattices form various small domain walls, and can be a surface effect as supported by our first-principles calculations. Crucially, we find that the amplitude of the energy gap opened by the charge order exhibits real-space modulations, and features 2 × 2 wave vectors with chirality, highlighting the electronic nature of the chiral charge order. STM study at 0.4 K reveals a superconducting energy gap with a gap size 2Δ = 0.85 meV, which estimates a moderate superconductivity coupling strength with 2Δ/k B T C = 3.9. Furthermore, when further applying a c-axis magnetic field, vortex core bound states are observed within this gap, indicative of clean-limit superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Investigating Ternary Li–Mg–Si Zintl Phase Formation and Evolution for Si Anodes in Li-Ion Batteries with Mg(TFSI) 2 Electrolyte Additive

Improved electrochemical performance of Si was recently reported by adding multivalent cation salts (such as Mg 2+ , Al 3+ , Ca 2+, etc.) in the electrolyte. This is achieved via the formation in an in situ manner of relatively more stable Li-M-Si ternary phases with less chemical reactivity. These phases stabilize Si anions and thus reduce side reactions with electrolytes at the surface and eventually benefit the overall electrochemistry. To understand the mechanism of ternary Zintl phase formation and its dynamics upon lithiation/delithiation, high-resolution solid-state 7 Li and 29 Si nuclear magnetic resonance (NMR) are utilized to directly probe the local Li and Si environments on Si electrodes harvested from coin and pouch cells at various states of (de)lithiation. The NMR spectra along with the electrochemical characterization reveal that lithiation of Si starts from the surface Si-O layer further confirmed by 7 Li– 29 Si cross-polarization NMR. Lithiation progresses with heterogeneous silicon clustering with Si -4 anions at high states of lithiation. At a fully lithiated state, the formation of overlithiated Si species is detected. At a low-voltage region (below 100 mV), direct evidence for Mg-ion insertion is found, postulated by two possible mechanisms: ion exchange with fully or overlithiated binary domains (Li 3.75+x Si) and/or a coinsertion with slightly underlithiated domains (similar to Li 3.55 Si). Upon delithiation, Li extraction starts from overlithiated Si domains. No evidence is found for electrochemical Mg removal. Evidence for a lithium-deficient Li y Mg 0.1 Si phase is found as a result of Li removal during charging. This investigation sheds light on the possible mechanisms of a new Si anode chemistry, which could enable the development of stable Si-based anodes for lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Probing the Reactivity of the Active Material of a Li-Ion Silicon Anode with Common Battery Solvents

Calculations and modeling have shown that replacing the traditional graphite anode with silicon can greatly improve the energy density of lithium-ion batteries. However, the large volume change of silicon particles and high reactivity of lithiated silicon when in contact with the electrolyte lead to rapid capacity fading during charging/discharging processes. In this report, we use specific lithium silicides (LS) as model compounds to systematically study the reaction between lithiated Si and different electrolyte solvents, which provides a powerful platform to deconvolute and evaluate the degradation of various organic solvents in contact with the active lithiated Si-electrode surface after lithiation. Nuclear Magnetic Resonance (NMR) characterization results show that a cyclic carbonate such as ethylene carbonate is chemically less stable than a linear carbonate such as ethylmethyl carbonate, fluoroethylene carbonate, and triglyme as they are found to be more stable when mixed with LS model compounds. Furthermore, guided by the experimental results, two ethylene carbonate (EC)-free electrolytes are studied, and the electrochemical results show improvements with graphite-free Si electrodes relative to the traditional ethylene-carbonate-based electrolytes. More importantly, the study contributes to our understanding of the significant fundamental chemical and electrochemical stability differences between silicon and traditional graphite lithium-ion battery (LIB) anodes and suggests a focused development of electrolytes with specific chemical stability vs lithiated silicon which can passivate the surface more effectively.

25 ENERGY STORAGE↗
DOE OSTI2021

LCLS2

This is the LCLS II development repository developed at SLAC National Accelerator Laboratory.

Dubrovin, Mikhail↗
DOE OSTI2021

Charge-spin interconversion in epitaxial Pt probed by spin-orbit torques in a magnetic insulator

We measure spin-orbit torques (SOTs) in a model system of all-epitaxial ferrite/Pt bilayers to gain insights into charge-spin interconversion in Pt. With negligible electronic conduction in the insulating ferrite, the crystalline Pt film acts as the sole source of charge-to-spin conversion. A small fieldlike SOT independent of Pt thickness suggests a weak Rashba-Edelstein effect at the ferrite/Pt interface. By contrast, we observe a sizable dampinglike SOT that depends on the Pt thickness, from which we deduce the dominance of an extrinsic spin-Hall effect (skew scattering) and Dyakonov-Perel spin relaxation in the crystalline Pt film. Furthermore, our results point to a large internal spin-Hall ratio of ≈ 0.8 in epitaxial Pt. Furthermore, our experimental work takes an essential step towards understanding the mechanisms of charge-spin interconversion and SOTs in Pt-based heterostructures, which are crucial for power-efficient spintronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Degradation of aromatic compounds and lignin by marine protist Thraustochytrium striatum

This paper aimed at studying a novel high biomass strain (HBS) of marine protist, Thraustochytrium striatum, for lignin valorization to lipids and carotenoids. In the screening of 15 aromatic compounds, T. striatum HBS can utilize most compounds while achieving the best growth on 3,4-dihydroxybenzoic acid (3,4-DHBA) and 4-hydroxybenzoic acid (4-HBA). The maximum cell mass concentration reached 2-3 g/L under 5 g/L of 3,4-DHBA or 2 g/L of 4-HBA, which was comparable to that under equivalent concentration of glucose. The long-chain fatty acids content was 13 % and 7 % with 3,4-DHBA and 4-HBA, respectively. The adoption of fed-batch fermentation mode improved the degradation of carbon source and prevented the inhibitory effect caused by overloading of aromatic compounds. Further, both final cellular fatty acids and carotenoids contents were doubled in the fermentation of 3,4-DHBA. T. striatum HBS exhibited limited lignin depolymerization (~24 %) ability on technical lignins.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Vacancy‐Enabled O3 Phase Stabilization for Manganese‐Rich Layered Sodium Cathodes

Abstract Manganese‐rich layered oxide materials hold great potential as low‐cost and high‐capacity cathodes for Na‐ion batteries. However, they usually form a P2 phase and suffer from fast capacity fade. In this work, an O3 phase sodium cathode has been developed out of a Li and Mn‐rich layered material by leveraging the creation of transition metal (TM) and oxygen vacancies and the electrochemical exchange of Na and Li. The Mn‐rich layered cathode material remains primarily O3 phase during sodiation/desodiation and can have a full sodiation capacity of ca. 220 mAh g −1 . It delivers ca. 160 mAh g −1 specific capacity between 2–3.8 V with >86 % retention over 250 cycles. The TM and oxygen vacancies pre‐formed in the sodiated material enables a reversible migration of TMs from the TM layer to the tetrahedral sites in the Na layer upon de‐sodiation and sodiation. The migration creates metastable states, leading to increased kinetic barrier that prohibits a complete O3‐P3 phase transition.

Xiao, Biwei↗
DOE OSTI2021

Examining CO 2 as an Additive for Solid Electrolyte Interphase Formation on Silicon Anodes

In this study, we demonstrate that the addition of CO 2 to a standard 1.0 M LiPF 6 3:7 wt% ethylene carbonate:ethyl methyl carbonate electrolyte results in the formation of a thinner insoluble solid electrolyte interphase (SEI) that is dominated by the presence of LiF. In contrast, cells without CO 2 result in a thicker insoluble SEI layer containing more organic constituents. The CO 2 is incorporated in the dimethyl carbonate soluble part of the SEI composed primarily of polymeric poly(ethylene oxide) (PEO) on the surface of a thin inorganic layer. This combination of properties from CO 2 addition provides an improved cycling performance through the reduction of irreversible side reactions, leading to higher coulombic efficiency. The results indicate that CO 2 incorporates into the SEI and plays a role similar to additives like fluorinated ethylene carbonate and vinylene carbonate with respect to polymeric components.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Design of High-Voltage Stable Hybrid Electrolyte with an Ultrahigh Li Transference Number

Considering the high energy consumption during processing, and the low compliance and adhesion of ceramic electrolytes, the integration of polymer into ceramic electrolytes provides a way to mitigate the interfacial issues. However, the severe ion concentration gradient, low ionic conductivity, and instability toward Li metal and high-voltage cathodes become the major concerns in applying hybrid electrolytes. In this work, we report a single-ionconducting hybrid electrolyte (SIE-LLZO) with 64 wt % Li 7 La 3 Zr 2 O 12 (LLZO) particles embedded in a fluoroboron-centered Li-conductive polymer framework (LiBFSIE). The SIE-LLZO electrolyte exhibited a high Li transference number of 0.94 and electrochemical stability up to 5.6 V vs Li/Li + . Promising averaged Coulombic efficiencies of 99.97% and 99.91% were achieved in cells with LiNi 0.8 Co 0.15 Al 0.05 O 2 and LiNi 0.6 Mn 0.2 Co 0.2 O2 cathodes for 400 and 200 cycles, respectively. Finally, the Li-conducting pathway in the hybrid electrolyte was further investigated by a 6 Li-to- 7 Li isotope replacement method, indicating that Li transport mainly relies on the LLZO and interface between LiBFSIE and LLZO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Stress- and interface-compatible red phosphorus anode for high-energy and durable sodium-ion batteries

Sodium-ion battery is a promising candidate for energy storage application, but the absence of high-capacity and low-cost anode materials significantly limit their practical specific energy and cost. Red phosphorus (RP) possesses a high theoretical specific capacity but suffers from large volume change, low electronic conductivity and unstable solid-electrolyte interphase (SEI). Herein, a hierarchical micro/nanostructured antimony-doped RP/carbon anode was developed, which demonstrate extraordinary electrochemical performance with high initial Coulombic efficiency of ~90%, high areal (~1.7 mAh cm-2) capacity together with good cycle stability and rate capability. Combined experimental and computational studies consistently revealed that such a unique structural design can dramatically accommodate the mechanical stress and moreover effectively restrain the undesired decomposition of electrolyte solvents regardless of electrolytes formulation, resulting in superior structural integrity and thin/robust SEI formation during cycling. The present finding has offered an alternative strategy for stress management and interface engineering on high-capacity alloying-based anode materials.

Liu, Xiang↗
DOE OSTI2021

Stoichiometric irreversibility of aged garnet electrolytes

Solid-state lithium batteries (SSLBs) have been regarded as one of the next-generation energy storage systems. With the adoption of solid-state electrolytes (SSEs) and lithium metal anodes, SSLBs enable higher energy density and more reliable safety than the state-of-the-art lithium-ion batteries. Among potential SSEs, the cation-doped Li 7 La 3 Zr 2 O 12 (LLZO) is promising for its high ionic conductivity (~10 –3 S cm –2 ) at room temperature and high stability with Li metal anode. However, the storage of doped LLZO in the ambient condition suffers the aging effect, including the structural transition (i.e. low-temperature cubic form) and the stoichiometric changes (i.e. Li 2 CO 3 ). These changes are detrimental to LLZO ionic conductivity and interfacial stability in SSLBs. To this end, in this study we are motivated to investigate the structural and stoichiometric reversibility of aged LLZO during thermal treatment. With the help of an in-situ synchrotron-based high-energy X-ray diffraction technique, our experiments revealed that the LLZO powders became a low-temperature cubic phase when exposed to the ambient condition for an extended period of time. A high temperature cubic form can be restored after a thermal treatment of the aged LLZO powder, regardless of the type of dopant. However, the restoration of the stoichiometry remained a challenge, and the degree of the restoration showed a clear dependence on the dopant chemistry.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electron-ion coincidence measurements of molecular dynamics with intense X-ray pulses

Molecules can sequentially absorb multiple photons when irradiated by an intense X-ray pulse from a free-electron laser. If the time delay between two photoabsorption events can be determined, this enables pump-probe experiments with a single X-ray pulse, where the absorption of the first photon induces electronic and nuclear dynamics that are probed by the absorption of the second photon. Here we show a realization of such a single-pulse X-ray pump-probe scheme on N 2 molecules, using the X-ray induced dissociation process as an internal clock that is read out via coincident detection of photoelectrons and fragment ions. By coincidence analysis of the kinetic energies of the ionic fragments and photoelectrons, the transition from a bound molecular dication to two isolated atomic ions is observed through the energy shift of the inner-shell electrons. Via ab-initio simulations, we are able to map characteristic features in the kinetic energy release and photoelectron spectrum to specific delay times between photoabsorptions. In contrast to previous studies where nuclear motions were typically revealed by measuring ion kinetics, our work shows that inner-shell photoelectron energies can also be sensitive probes of nuclear dynamics, which adds one more dimension to the study of light-matter interactions with X-ray pulses.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Stabilizing Anionic Redox Chemistry in a Mn-Based Layered Oxide Cathode Constructed by Li-Deficient Pristine State

Li-rich cathode materials are of significant interest for coupling anionic redox with cationic redox chemistry to achieve high-energy-density batteries. However, lattice oxygen loss and derived structure distortion would induce serious capacity loss and voltage decay, further hindering its practical application. Herein, a novel Li-rich cathode material, O3-type Li 0.6 [Li 0.2 Mn 0.8 ]O 2 , is developed with the pristine state displaying both a Li excess in the transition metal layer and a deficiency in the alkali metal layer. Benefiting from stable structure evolution and Li migration processes, not only can high reversible capacity (≈329 mAh g -1 ) be harvested but also irreversible/reversible anionic/cationic redox reactions are comprehensively assigned via the combination of in/ex situ spectroscopies. Furthermore, irreversible lattice oxygen loss and structure distortion are effectively restrained, resulting in long-term cycle stability (capacity drop of 0.045% per cycle, 500 cycles). Altogether, tuning the Li state in the alkali metal layer presents a promising way for modification of high-capacity Li-rich cathode candidates.

anionic redox reactions↗
DOE OSTI2020

Differentiating and Quantifying Gas-Phase Conformational Isomers Using Coulomb Explosion Imaging

Conformational isomerism plays a crucial role in defining the physical and chemical properties and biological activity of molecules ranging from simple organic compounds to complex biopolymers. However, it is often a significant challenge to differentiate and separate these isomers experimentally as they can easily interconvert due to their low rotational energy barrier. Here, we use the momentum correlation of fragment ions produced after inner-shell photoionization to distinguish conformational isomers of 1,2-dibromoethane (C 2 H 4 Br 2 ). We demonstrate that the three-body breakup channel, C 2 H 4 + + Br + + Br + , contains signatures of both sequential and concerted breakup, which are decoupled to distinguish the geometries of two conformational isomers and to quantify their relative abundance. The sensitivity of our method to quantify these yields is established by measuring the relative abundance change with sample temperature, which agrees well with calculations. Finally, our study paves the way for using Coulomb explosion imaging to track subtle molecular structural changes.

Photoionization↗