Engineering Papers⌕ Search

Engineering topics

Li, Nan

Publications and source records attributed to Li, Nan.

At least 109 records · Page 6

Linking energy-cyber-physical systems with occupancy prediction and interpretation through WiFi probe-based ensemble classification

With the rapid advances in sensing and digital technologies, cyber-physical systems are regarded as the most viable platforms for improving building design and management. Researchers investigated the possibility of integrating energy management systems with cyber-physical systems to form energy-cyber-physical systems in order to promote building energy management. However, minimizing energy consumption while fulfilling building functions for energy-cyber-physical systems is challenging due to the dynamics of building occupants. As occupant behavior is a major source of uncertainty for energy management, ignoring it often results in both energy waste caused by overheating and overcooling as well as discomfort due to insufficient thermal and ventilation services. To mitigate such uncertainties, this study proposes an occupancy-linked energy-cyber-physical system that incorporates WiFi probe-based occupancy detection. The proposed framework utilizes ensemble classification algorithms to extract three forms of occupancy information. It creates a data interface to link energy management systems and cyber-physical systems and allows for automated occupancy detection and interpretation by assembling multiple weak classifiers for WiFi signals. A validation experiment in a large office room was conducted to examine the performance of the proposed occupancy-linked energy-cyber-physical systems. The experiment and simulation results suggest that, with a proper classifier and occupancy data type, the proposed model can potentially save about 26.4% of energy consumption in cooling and ventilation demands.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Nanoindentation Analysis of Ion Irradiated FeCrAl C26M

The present report summarizes the irradiation hardening behavior of two FeCrAl alloys, C26M and B126Y, irradiated up to a damage level of 16 dpa. Nanoindentation values were averaged between a depth of 100 and 200 nm in order to capture the irradiated region only. At the highest damage level, C26M was measured to harden by 1.62 GPa with little change in the modulus. B126Y showed a change in hardness of up to 2.52 GPa, reaching a similar hardness to the C26M. To more accurately compare with the unirradiated material where the influence of indentation size effects may operate more strongly, the Nix-Gao model was used to calculate the hardness at infinite depth, H0, and the length scale term, h*. The change in hardness with this model was found to be lower for both C26M and B126Y. The length scale term decreased with increasing dose up to 4 dpa and then deviated from expectation with a significant i ncrease at 16 dpa for both specimens. Spherical nanoindentation was performed on all specimens. A 5 μm tip was used to ensure the yield point occurred in the irradiated region. While the results from this testing are not as conclusive at doses less than 4 dpa, the nanoindentation yield strength showed similar trends with the nanoindentation hardness data.

36 MATERIALS SCIENCE↗

Nanoindentation Characterization of FeCrAl C26M tubes

The present report summarizes the nanoindentation characterization of a FeCrAl alloy, C26M in both tube and bar form. Microstructural analysis on the tube using electron backscatter diffraction showed a textured system with the cross-section favoring orie ntations near the [110] and the tube surface near the [111]. The bar cross-section showed a texture with orientation favoring those near the [100]. A large amount of in-grain misorientation was observed in the tube specimen with very little in the bar, indicating cold-work from tube processing steps. Nanoindentation with a Berkovich tip measured a similar modulus for all specimens of ~220 GPa. The bar specimens had a hardness of ~3.9 GPa, significantly lower than the 4.8 GPa and 5.2 GPa for the tube cross-section and surface, respectively. Spherical nanoindentation was performed on all specimens and orientations. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa for all specimens, in agreement with the Berkovich indentation results. The nanoindentation yield strength for the bar was found to be ~0.8 - 0.9 GPa, nearly 0.5 GPa less than the C26M tube.

36 MATERIALS SCIENCE↗

Surface Passivation and Carrier Collection in {110}, {100} and Circular Si Microwire Solar Cells

Surface recombination is a major bottleneck for realizing highly efficient micro/nanostructure solar cells. Parametric studies of the influence of Si microwire (SiMW) surface-facet orientation (rectangular with flat-facets, {110}, {100} and circular), with a fixed height of 10 µm, diameter (D = 1.5–9.5 µm), and sidewall spacing (S = 2.5–8.5 µm), and mesh-grid density (1–16 mm -2 ) on recombination and carrier collection in SiMW solar cells with radial p-n junctions are reported. An effective surface passivation layer composed of thin thermally grown silicon dioxide (SiO 2 ) and silicon nitride (SiN x ) layers is employed. For a fixed D of 1.5 µm, tight SiMW spacing results in improved short-circuit current density (J sc = 30.1 mA cm -2 ) and sparse arrays result in open-circuit voltages (V oc = 0.552 V) that are similar to those of control Si planar cells. For a fixed S, smaller D results in better light trapping at shorter wavelengths and higher J sc while larger D exhibits better light trapping at larger wavelengths and a higher V oc . With a mesh-grid electrode the power conversion efficiency increases to 15.3%. Finally, these results provide insights on the recombination mechanisms in SiMW solar cells and provide general design principles for optimizing their performance.

14 SOLAR ENERGY↗

Oxide Morphology of C26M at 300 - 600 °C

Iron-chromium-aluminum (FeCrAl) alloys are of interest to the nuclear materials community due to their resistance to high temperature steam oxidation under accident conditions. The present work investigates oxide formation at temperatures relevant to light water reactor cladding operation following extended aging to assess growth kinetics, chemical composition, and microstructure of oxide formation on an Oak Ridge National Laboratory developed Fe-12Cr-6Al- 2Mo-0.2Si-0.03Y alloy (designated ‘C26M’). Aging treatments were performed for 100-2000 hours in stagnant air at 300, 400, 500, and 600 °C, respectively. Oxide growth behavior under the investigated conditions follows a logarithmic time dependence. When the oxidization temperature is 400 °C or below, the oxide is amorphous. At 500 °C, crystalline α-Al 2 O 3 oxide film develops and the correlated logarithmic rate constant decreases significantly, indicating enhanced oxidation resistance of the formed oxide film. In addition, Mo segregation at grain boundaries has been observed when the aging temperature exceeds 500 °C. The results of this study can be viewed as an upper bounding result for potential oxide coarsening on the cladding inner surface during reactor operation.

36 MATERIALS SCIENCE↗

The roles of interfaces and other microstructural features in Cu/Nb nanolayers as revealed by in situ beam bending experiments inside an scanning electron microscope (SEM)

Interfaces and their interactions with other microstructural features, such as grain boundaries or twin structures, have been widely viewed as parameters for designing metallic nanolayers. These interfaces could play a role in hindering cracks from propagating across the nanolayers while in operation. To date, many studies have focused on the roles of interfaces in affecting the plasticity mechanisms and thus the deformability of nanolayers. However, no studies have investigated on the subsequent mechanisms of fracture leading to the final failure. In this study, in situ microfracture bending tests inside a scanning electron microscope (SEM) were performed on the notched clamped beams of Cu/Nb nanolayers with a similar layer thickness using two different fabrication processes: physical vapor deposition (PVD) and accumulative roll bonding (ARB). Due to the columnar grains of the Cu/Nb PVD beams, a sudden catastrophic linear elastic, brittle fracture phenomenon was observed; in the Cu/Nb ARB beams, fracture events of notch widening phase and crack initiation and fracture along the shear instability were observed. Detailed examinations showed the presence of competing mechanisms between the multilayered interface, columnar grain boundary, and experimental factors of beam geometry and the position of the tip. With this newfound knowledge, new types of metallic nanolayers can be designed with enhanced strength and fracture resistant properties.

36 MATERIALS SCIENCE↗

Quantifying heterogeneous deformation in grain boundary regions on shock loaded tantalum using spherical and sharp tip nanoindentation

Grain boundaries play an important role in the overall mechanical performance of metals and alloys; however, isolating the effects of individual grain boundaries remains rather challenging experimentally. In this work, wire-feed, electron beam additively manufactured tantalum is studied under shock loading conditions generating incipient spall damage. Three grain boundaries aligned parallel to the shock direction were isolated inside a single sample. Postmortem metallography showed voids preferentially appeared on two of the three grain boundaries which had high misorientation angles > 30° compared to the third grain boundary with a relatively lower misorientation angle < 10°. Nanoindentation in grain boundary regions for both pyramidal and spherical tips showed characteristically different strain hardening trends for each grain boundary. Significant local strain hardening is present on both sides of one high angle grain boundary, while strain softening is captured at the other high angle grain boundary. A negligible trend of either hardening or softening is shown in the vicinity of the single low angle grain boundary. As a result, this leads to the conclusion that the trend of strain hardening/softening in grain boundary regions is not monotonically correlated to the susceptibility of specific grain boundaries to an increased propensity for void damage.

36 MATERIALS SCIENCE↗

Nanoindentation Characterization of FeCrAl C26M Welds

The present report summarizes the initial mechanical characterization of a welded FeCrAl alloy, C26M, with comparison to two other welded specimens, C35M and C37M. The welded C26M showed a larger fusion and heat-affected zone than either the C35M or C37M welds. Nanoindentation hardness measurements using a Berkovich tip showed no major changes in the hardness and modulus between the fusion zone, heat-affected zone, and unaffected C26M tube. Nanoindentation strain-rate sensitivity tests were also performed and showed no changes between each of the regions in the C26M weld. Spherical nanoindentation tests were carried out to evaluate the nanoindentation modulus and nanoindentation yield strength in each of the regions of the C26M weld sample. No significant changes in strength from welding were observed with an average nanoindentation yield strength of ~1 GPa and nanoindentation modulus of ~220 GPa. Nanoindentation tests all show that the C26M does not change significantly after welding and that further characterization with some form of tensile loading is necessary to determine if any significant change has occurred.

36 MATERIALS SCIENCE↗

Renal ischemia/reperfusion-induced mitophagy protects against renal dysfunction via Drp1-dependent-pathway

Highlights: • mitophagy was observed in renal after IRI in comparison to control. • Drp1 is activated by S616 phosphorylation and S637 dephosphorylation, and translocates to mitochondria after renal IRI. • drp1-dependent mitophagy plays a protective role against IRI-induced apoptosis and renal dysfunction. Autophagy is upregulated under stress conditions to degrade superfluous proteins and recycle damaged organelles including damaged mitochondria. However, the occurrence of mitochondrial autophagy and its contribution remain to be elucidated during renal ischemia/reperfusion injury (IRI). In this study, mitophagosomes and engulfed mitochondria were frequently observed by electron microscopy after renal IRI vs. control. Meanwhile, the increase of lipidated microtubule associated protein light chain 3 (LC3-II) and decrease of mitochondrial proteins were detected by western blot, suggesting the presence of mitophagy. Drp1 translocated to mitochondria and was phosphorylated at S616 in response to IRI. Interestingly, we found that inhibiting drp1 phosphorylation with mdivi-1 significantly suppressed IRI-induced mitophagy without affecting general autophagy. Furthermore, our results showed that downregulation of mitophagy significantly exacerbated cell apoptosis and markedly aggravated kidney dysfunction induced by IRI. Taken together, these data indicate that mitophagy was activated via Drp1-dependent pathway and such mitophagic clearance of damaged mitochondria protects cells from IRI-induced apoptosis.

60 APPLIED LIFE SCIENCES↗

Microstructural Characterization of FeCrAl C26M Tubes

The present report summarizes the initial nanoindentation characterization of a FeCrAl alloy, C26M. Microstructural analysis using electron backscatter diffraction showed a highly textured system with the axial surface favoring orientations near the [110] and the longitudinal surface near the [111]. A large spread of grain sizes was observed from a few μm’s to 100 μm with an average grain size of ~70 μm. Nanoindentation with a Berkovich tip measured a similar hardness and modulus of ~4.4 GPa and ~240 GPa on the two surfaces, respectively. Mounting specimens in epoxy was found to be the cause of a lower stiffness and, consequently, a lower hardness and modulus value. Spherical nanoindentation was measured on the longitudinal surface of the tube to determine the nanoindentation modulus and nanoindentation yield strength. Using a 10 μm tip, the measured modulus was ~220 GPa and the yield strength was ~1.4 GPa. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa and yield strength of ~1.1 GPa. Some early characterization of the differences in spherical nanoindentation response of the axial and longitudinal surfaces showed a small difference between the two, but a more detailed analysis with a stiffer mounting configuration is needed to draw conclusions.

36 MATERIALS SCIENCE↗

Mapping Soil Cation‐Exchange Capacity using Bayesian Modeling and Proximal Sensors at the Field Scale

Core Ideas A Bayesian inference approach (INLA‐SPDE) was used to map topsoil and subsoil CEC. DEM, gamma‐ray spectrometer and EM induction data were combined to map CEC. Posterior marginal distributions of the model parameters and responses were estimated. Gamma‐ray data performed best in the topsoil, followed by DUALEM421S and elevation. Elevation data performed best in the subsoil, followed by gamma‐ray and DUALEM421S. Cation exchange capacity (CEC) affects soil fertility, acidity, and structural resilience. This is particularly the case in sugarcane growing areas of Australia because the soil there is sandy (>60%), strongly acidic (pH < 5.5), and strongly sodic (exchangeable sodium percentage [ESP] > 15%). Unfortunately, obtaining information on CEC at the field extent is time‐consuming and expensive. Here, we used a digital soil mapping approach to add value to limited (40) topsoil (0–0.3 m) and subsoil (0.6–0.9 m) CEC information. We first collected proximally sensed ancillary data from three sources, including a digital elevation model (DEM), γ‐ray (γ‐ray) spectrometer (RS700) and electromagnetic (EM) induction instruments. We then use a Bayesian inference approach (Integrated Nested Laplace Approximation with Stochastic Partial Differential Equation, INLA‐SPDE) implemented in R software to model the CEC and ancillary data. Accuracy (RMSE), bias (ME), and concordance (Lin's) of models were also generated from the different sources of ancillary data, either in combination or alone. We concluded, overall, that the INLA–SPDE approach could provide estimations of the posterior marginal distributions of the model parameters as well as the model responses as reported by other researchers. We also concluded that using the ancillary data sources in combination was most accurate (e.g., RMSE = 0.72) to predict CEC, least biased (e.g., ME = 0.07) and had the highest concordance (e.g., Lin's = 0.69) in both the topsoil and subsoil than using the ancillary data alone. The best ancillary data, when used alone for mapping CEC in the topsoil, was γ‐ray spectrometry, followed by EM data and elevation. For subsoil CEC, it was elevation, followed by γ‐ray spectrometry and then soil electrical conductivity (EC a ) data. The maps of the credibility interval (CI) indicated that better predictions were achieved in the topsoil and indicated where improvements in prediction could be achieved in the subsoil.

Li, Nan↗

Slip transmission of high angle grain boundaries in body-centered cubic metals: Micropillar compression of pure Ta single and bi-crystals

In this study, we seek to probe and understand the mechanical behavior of grain boundaries in pure Ta as a model bcc material using micropillar compression experiments. Three high angle grain boundaries are chosen with varying crystal orientations. Multiple bi-crystal pillars are prepared containing a single, nearly vertical grain boundary in the approximate center of the pillar and compared against their single crystalline pillar counterparts. The main phenomenon of interest was slip transmission or strain transfer in the bi-crystals which was considered to occur when slip traces aligned across the grain boundary. This occurred in two of the three bi-crystals.

36 MATERIALS SCIENCE↗

Radiation damage in nanostructured materials

Materials subjected to high dose irradiation by energetic particles often experience severe damage in the form of drastic increase of defect density, and significant degradation of their mechanical and physical properties. Extensive studies on radiation effects in materials in the past few decades show that, although nearly no materials are immune to radiation damage, the approaches of deliberate introduction of certain types of defects in materials before radiation are effective in mitigating radiation damage. Nanostructured materials with abundant internal defects have been extensively investigated for various applications. The field of radiation damage in nanostructured materials is an exciting and rapidly evolving arena, enriched with challenges and opportunities. In this review article, we summarize and analyze the current understandings on the influence of various types of internal defect sinks on reduction of radiation damage in primarily nanostructured metallic materials, and partially on nanoceramic materials. We also point out open questions and future directions that may significantly improve our fundamental understandings on radiation damage in nanomaterials. Finally, the integration of extensive research effort, resources and expertise in various fields may eventually lead to the design of advanced nanomaterials with unprecedented radiation tolerance.

36 MATERIALS SCIENCE↗

Examining the influence of grain size on radiation tolerance in the nanocrystalline regime

Here, nanocrystalline materials have been proposed as superior radiation tolerant materials in comparison to coarse grain counterparts. However, there is still a limited understanding whether a particular nanocrystalline grain size is required to obtain significant improvements in key deleterious effects resulting from energetic irradiation. This work employs the use of in-situ heavy ion irradiation transmission electron microscopy experiments coupled with quantitative defect characterization and precession electron diffraction to explore the sensitivity of defect size and density within the nanocrystalline regime in platinum. Under the explored experimental conditions, no significant change in either the defect size or density between grain sizes of 20 and 100 nm was observed. Furthermore, the in-situ transmission electron microscopy irradiations illustrate stable sessile defect clusters of 1-3 nm adjacent to most grain boundaries, which are traditionally treated as strong defect sinks. The stability of these sessile defects observed in-situ in small, 20-40 nm, grains is the proposed primary mechanism for a lack of defect density trends. Lastly, this scaling breakdown in radiation improvement with decreasing grain size has practical importance on nanoscale grain boundary engineering approaches for proposed radiation tolerant alloys.

36 MATERIALS SCIENCE↗