Engineering Papers⌕ Search

Engineering topics

Ladany, I.

Publications and source records attributed to Ladany, I..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Laser to single-mode-fiber coupling: A laboratory guide

All the information necessary to achieve reasonably efficient coupling of semiconductor lasers to single mode fibers is collected from the literature, reworked when necessary, and presented in a mostly tabular form. Formulas for determining the laser waist radius and the fiber mode radius are given. Imaging relations connecting these values with the object and image distances are given for three types of lenses: ball, hemisphere, and Gradient Index (GRIN). Sources for these lenses are indicated, and a brief discussion is given about ways of reducing feedback effects.

Ladany, I.↗
NASA NTRS1990

Structures and characteristics of commercially available 1.5 micron InGaAsP distributed feedback laser diodes

The characteristics of commercially available 1.5-micron distributed feedback (DFB) laser diodes obtained from seven manufacturers were investigated, and the results are correlated with the lasers' structural parameters. It was found that buried heterostructures with first-order gratings showed consistently good results (as opposed to buried heterostructures with second-order gratings). A ridge waveguide laser was near the bottom of most performance charts.

Cook, A. L.↗
NASA NTRS1989

Approaches toward a blue semiconductor laser

Possible approaches for obtaining semiconductor diode laser action in the blue region of the spectrum are surveyed. A discussion of diode lasers is included along with a review of the current status of visible emitters, presently limited to 670 nm. Methods are discussed for shifting laser emission toward shorter wavelengths, including the use of II-IV materials, the increase in the bandgap of III-V materials by addition of nitrogen, and changing the bandstructure from indirect to direct by incorporating interstitial atoms or by constructing superlattices. Non-pn-junction injection methods are surveyed, including avalanche breakdown, Langmuir-Blodgett diodes, heterostructures, carrier accumulation, and Berglund diodes. Prospects of inventing new multinary semiconducting materials are discussed, and a number of novel materials described in the literature are tabulated. New approaches available through the development of quantum wells and superlattices are described, including resonant tunneling and the synthesis of arbitrary bandgap materials through multiple quantum wells.

Ladany, I.↗
NASA NTRS1988

Distributed feedback lasers

A ridge waveguide distributed feedback laser was developed in InGaAsP. These devices have demonstrated CW output powers over 7 mW with threshold currents as low as 60 mA at 25 C. Measurements of the frequency response of these devices show a 3 dB bandwidth of about 2 GHz, which may be limited by the mount. The best devices have a single mode spectra over the entire temperature range tested with a side mode suppression of about 20 dB in both CW and pulsed modes. The design of this device, including detailed modeling of the ridge guide structure, effective index calculations, and a discussion of the grating configuration are presented. Also, the fabrication of the devices is presented in some detail, especially the fabrication of and subsequent growth over the grating. In addition, a high frequency fiber pigtailed package was designed and tested, which is a suitable prototype for a commercial package.

Ladany, I.↗
NASA NTRS1986

Wedged Fibers Suppress Feedback of Laser Beam

When injected laser is coupled into optical fiber, emission instabilities arise because of optical feedback losses from fiber into laser. Coupling efficiencies as high as 80 percent, however, obtained by shaping end of multimode fiber into obtuse-angled wedge. Because slanted sides eliminate back reflection, such wedged fiber achieves high coupling efficiency.

Ladany, I.↗
NASA NTRS1986

Scandium oxide antireflection coatings for superluminescent LEDs

For an employment of laser diodes as superluminescent LEDs (SLDs) or amplifiers, the facets of the diodes must be coated with antireflection films. In the work reported, scandium oxide was evaporated from an e-beam source onto Supersil II fused silica substrates. The obtained samples were used for measurements of absorption and reflectivity. Results of index measurements on e-beam evaporated films are presented. It is shown that excellent coatings with reflectivities of 0.00025 can be obtained using these films. Attention is given to the refractive indices for scandium oxide films as a function of wavelength, the power output vs current for laser before coating and after coating with Sc2O3.

Ladany, I.↗
NASA NTRS1984

Modified Fabrication for InGaAsP Strip Laser

Improved fabrication of InGaAsP stripe lasers involves replacement of oxide stripe in quaternary laser by an n-type layer of InP grown on top of quaternary cap layer. Process allows use of stop etch that selectively removes InP and does not etch InGaAsP, making fabrication especially convenient.

Ladany, I.↗
NASA NTRS1983

The AlGaAs single-mode stability

Single-mode spectral behavior with aging in constricted double heterojunction (CDH) lasers was studied. The CDH lasers demonstrated excellent reliability ( or = 1 million years extrapolated room-temperature MTTF) and single-mode operation after 10,000 hours of 70 C aging. The deleterious effects of laser-fiber coupling on the spectra of the diodes were eliminated through the use of wedge-shaped fibers. A novel high-power large optical cavity (LOC)-type laser was developed: the terraced-heterostructure (TH)-LOC laser, which provides the highest power into a single-mode (i.e., 50 mW CW) ever reported.

Botez, D.↗
NASA NTRS1983

Wedge coupling of lasers into multimode fibers

Design and experimental data for obtuse-angled wedges used in coupled configurations of diode lasers and multimode fibers are presented. An analytic definition of the connection between the wedge angle and the fiber acceptance half-angle is developed, along with a formula for the minimum half-angle. An inequality is defined for determining the bevel angle of the output end of the fiber to eliminate end reflections. The fiber parameters are accounted for in the bevel. The formulations were tested in comparison with the performance of a coupled CDH laser system and good agreement was found in the output spectrum.

Ladany, I.↗
NASA NTRS1983

Ohmic contacts for laser diodes

Requirements for ohmic contacts to laser diodes are discussed, and properties of Schottky barrier tunneling contacts are reviewed. A procedure is described for measuring contact resistance on fabricated laser material without the need for specially constructed samples and contact configurations. Measurements of contact resistance and estimates of specific contact resistance are given for Ti/Pt/Au contacts to surfaces with three different doping levels. It was found that below a p-type carrier concentration of 1 x 10 to the 19th per cu cm the contact resistance is likely to be too high for good device performance. At higher doping levels, a specific contact resistance as low as 2 x 10 to the -6th ohm sq cm was obtained. Oxide stripe lasers provided with the type of contact discussed in this paper have been operated without failures for periods up to 7 years at a current density at the contact of 6-8 kA/sq cm. It appears therefore that these contacts satisfy the need for low resistance and durability and that, at the same time, they do not cause any obvious material degradation.

Ladany, I.↗
NASA NTRS1981

InGaAsP/InP laser development for single-mode, high-data-rate communications

Materials studies as well as general and specific device development were carried out in the InGaAsP system. A comparison was made of three standard methods of evaluating substrate quality by means of dislocation studies. A cause of reduced yield of good wafers, the pullover of melt from one bin to the next, has been analyzed. Difficulties with reproducible zinc acceptor doping have been traced to segregation of zinc in the In/Zn alloy used for the doping source. Using EBIC measurments, the pn junction was shown to drift in location depending on factors not always under control. An analysis of contact structures by SIMS showed that the depth to which the sintered Au/Zn contact penetrates into the structure is typically 0.13 microns, or well within the cap layer and out of the p-type cladding and thus not deleterious to laser prformance. The problem of single-mode laser development was investigated and it was shown to be related to the growth habit over four different possible substrate configurations. The fabrication of constricted double heterojunctions, mesa stripe buried heterostructures, and buried heterostructures was discussed, and measurements were presented on the device properties of single-mode buried heterostructure lasers. Results include single spectral line emission at 3 mW and a threshold current of 60 mA.

Ladany, I.↗
NASA NTRS1980

Single-mode laser studies: Design and performance of a fixed-wave length source and coupling of lasers to thin-film optical waveguides

A module developed for the generation of a stable single wavelength to be used for a fiber optic multiplexing scheme is described. The laser is driven with RZ pulses, and the temperature is stabilized thermoelectrically. The unit is capable of maintaining a fixed wavelength within about 6 A as the pulse duty cycle is changed between 0 and 100 percent. This is considered the most severe case, and much tighter tolerances are obtainable for constant input power coding schemes. Using a constricted double heterostructure laser, a wavelength shift of 0.083 A mA is obtained due to laser self-heating by a dc driving current. The thermoelectric unit is capable of maintaining a constant laser heat-sink temperature within 0.02 C. In addition, miniature lenses and couplers are described which allow efficient coupling of single wavelength modes of junction lasers to thin film optical waveguides. The design of the miniature cylinder lenses and the prism coupling techniques allow 2 mW of single wavelength mode junction laser light to b coupled into thin film waveguides using compact assemblies. Selective grating couplers are also studied.

Ladany, I.↗
NASA NTRS1980

Study of LPE methods for growth of InGaAsP/InP CW lasers

Two methods for liquid phase growth of InGaAsP/InP lasers were studied. Single phase growth, based on saturated melts and 5 C supercooling, was compared to two phase growth excess InP and 20 C nominal supercooling. Substrates cut on the (100) plane were used, and morphology in both cases was excellent and comparable to that obtainable in AlGaAs materials. A high degree of reproducibility was obtained in the materials grown by the two phased method, which is therefore presently preferred for the preparation of laser material. A refractive index step of 0.28 and an index n = 3.46 were obtained for In.81Ga.19As,5P5 lasing at 1.3 microns. Oxide-stripe lasers with typical room temperature cw threshold currents of 180 mA were obtained and some of them showed single mode behavior without lateral cavity modifications. COntinuous operation of 800 h at room temperature was obtained without noticeable degradation.

Ladany, I.↗
NASA NTRS1979

Internal stress and degradation in short-wavelength AlGaAs double-heterojunction devices

Aging tests of incoherently operated zinc-doped double-heterojunction (DH) lasers designed for short-wavelength (0.71-0.72 micron) operation show that the introduction of buffer layers between the substrate and the DH structure leads to a drastic reduction in gradual degradation. This is attributed to a decrease in lattice mismatch stress.

Ladany, I.↗
NASA NTRS1978

Protective coating for laser diodes

Coating for GaAs laser diodes should not alter optical and electrical properties. Borosilicate glass coating is easy to apply, breaks evenly when cleaved, and is abrasion and moisture resistant. Its low index of refraction makes thickness less critical when depositing half-wavelength coating.

Ladany, I.↗
NASA NTRS1978

The 1.1 micrometer and visible emission semiconductor diode lasers

In (AlGa)As, the first of three alloy systems studied, Continuous Wave (CW) operation was obtained at room temperature at a wavelength as low as 7260 A. Reliability in this system was studied in the incoherent mode. Zinc doped devices had significant degradation, whereas Ge or Ge plus Zi doped devices had none. The Al2O3 facet coatings were shown to significantly reduce facet deterioration in all types of lasers, longer wavelength units of that type having accumulated (at the time of writing) 22,000 hours with little if any degradation. A CL study of thin (AlGa)As layers revealed micro fluctuation in composition. A macro-scale fluctuation was observed by electroreflectance. An experimental and theoretical study of the effect of stripe width on the threshold current was carried out. Emission below 7000 A was obtained in VPE grown Ga(AsP) (In,Ga)P with CW operation at 10 C. Lasers and LED's were made by LPE in (InGa) (AsP). Laser thresholds of 5 kA/cm2 were obtained, while LED efficiences were on the order of 2%. Incoherent life test over 6000 hours showed no degradation.

Ladany, I.↗
NASA NTRS1978

Cathodoluminescence of Al/x/Ga/1-x/As grown by liquid-phase epitaxy

Small-area contrast fluctuations observed in cathodoluminescence-mode SEM images of thin Al(x)Ga(1-x)As layers grown by liquid-phase epitaxy on GaAs:Cr substrates are attributed to local variations in alloy composition. Quantitative estimates of the composition excursions are obtained from the variations in CL intensity by calibration against compositions known from electron-probe microanalysis. In a typical sample, the CL variations are shown to correspond to peak-to-peak fluctuations of about 1 at. % of Al and occur over irregular regions generally in the range 6-20 microns in diameter.

Levin, E. R.↗