Engineering Papers⌕ Search

Engineering topics

Kuo, B. C.

Publications and source records attributed to Kuo, B. C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Design of the annular suspension and pointing system /ASPS/ through decoupling and pole placement

A decoupling and pole-placement technique has been developed for the Annular Suspension and Pointing System (ASPS) of the Space Shuttle which uses bandwidths as performance criteria. The dynamics of the continuous-data ASPS allows the three degrees of freedom to be totally decoupled by state feedback through constant gains, so that the bandwidth of each degree of freedom can be independently specified without interaction. Although it is found that the digital ASPS cannot be completely decoupled, the bandwidth requirements are satisfied by pole placement and a trial-and-error method based on approximate decoupling.

Kuo, B. C.↗
NASA NTRS1979

Digital controller design: Analysis of the annular suspension pointing system

The Annular Suspension and Pointing System (ASPS) is a payload auxiliary pointing device of the Space Shuttle. The ASPS is comprised of two major subassemblies, a vernier and a coarse pointing subsystem. The experiment is attached to a mounting plate/rim combination which is suspended on magnetic bearing/actuators (MBA) strategically located about the rim. Fine pointing is achieved by gimballing the plate/rim within the MBA gaps. Control about the experiment line-of-sight is obtained through the use of a non-contacting rim drive and positioning torquer. All sensors used to close the servo loops on the vernier system are noncontacting elements. Therefore, the experiment is a free-flyer constrained only by the magnetic forces generated by the control loops.

Kuo, B. C.↗
NASA NTRS1979

The modeling and design of the Annular Suspension and Pointing System /ASPS/

The Annular Suspension and Pointing System (ASPS) is a payload auxiliary pointing device of the Space Shuttle. The ASPS is comprised of two major subassemblies, a vernier and a coarse pointing subsystem. The three functions provided by the ASPS are related to the pointing of the payload, centering the payload in the magnetic actuator assembly, and tracking the payload mounting plate and shuttle motions by the coarse gimbals. The equations of motion of a simplified planar model of the ASPS are derived. Attention is given to a state diagram of the dynamics of the ASPS with position-plus-rate controller, the nonlinear spring characteristic for the wire-cable torque of the ASPS, the design of the analog ASPS through decoupling and pole placement, and the time response of different components of the continuous control system.

Kuo, B. C.↗
NASA NTRS1978

Digital controller design: Analysis of the annular suspension pointing system

The analog controllers of the annular suspension pointing system are designed for control of the chi, phi sub 1, and phi sub 2 bandwidth dynamics through decoupling and pole placement. Since it is virtually impossible to find an equivalent bandwidth of the overall system and establish a general eigenvalue requirement for the system, the subsystem dynamics are decoupled through state feedback and the poles are placed simultaneously to realize the desired bandwidths for the three system components. Decoupling and pole placement are also used to design the closed-loop digital system through approximation.

Kuo, B. C.↗
NASA NTRS1976

Research study on IPS digital controller design

The performance is investigated of the simplified continuous-data model of the Instrument Pointing System (IPS). Although the ultimate objective is to study the digital model of the system, knowledge on the performance of the continuous-data model is important in the sense that the characteristics of the digital system should approach those of the continuous-data system as the sampling period approaches zero.

Kuo, B. C.↗
NASA NTRS1976

Stability analysis of the discrete-data Large-Space-Telescope system

This paper considers the application of the discrete describing function to the stability analysis of the Large-Space Telescope (LST) system. An analytical model of the CMG gimbal friction is derived, which is then used to arrive at a closed-form analytical expression for the discrete describing function of the nonlinearity. The analysis is used for the study of the fine-pointing stability of the LST vehicle. Simulation results corroborate the conclusions from the analytical analysis.

Kuo, B. C.↗
NASA NTRS1975

Research study on stabilization and control. Modern sampled-data control theory: Stability analysis of the low cost large space telescope system

The pointing stability of the low-cost large space telescope (LST) system was investigated. The low-cost LST is characterized by the use of reaction wheels for the generation of control torques. Because of the critical requirement on the pointing accuracy of the LST, the nonlinear frictional characteristics of the bearings of the reaction wheels were studied which can cause limit cycles in a closed-loop system. Another possible source of pointing error in the LST is due to the effect of quantization and sensor noise. Since the LST is a digital system, digital to analog and analog to digital converters and sensors for positional and rate feedbacks were used. Sensor noise and amplitude quantization causes pointing error in the LST and, in addition, quantization is a nonlinear phenomenon which can cause self-sustained oscillations in the closed-loop system. The dynamic modeling of the single-axis LST is described, and several methods of evaluating the attitude error of the digital LST due to quantization and noise inputs are given.

Kuo, B. C.↗
NASA NTRS1975

Limit cycle analysis of large space telescope with CMG nonlinearity

The existence and characteristics of self-sustained oscillations were studied in the Large Space Telescope (LST) system due to the presence of nonlinear gimbal friction in the control moment gyroscopes (CMG's). A continuous data single-axis model of the LST is considered. A solid friction model is used to represent CMG gimbal friction. A rigorous mathematical model is derived for use in a continuous describing function analysis. Conditions for self-sustained oscillations are then determined.

Seltzer, S. M.↗
NASA NTRS1975

Research study on stabilization and control. Modern sampled-date control theory. Stability analysis of the low cost large space telescope system

A mathematical model employing Fourier series is used to show quantization and reaction wheel friction nonlinearity in a telescope system for use in space. Block diagrams are used to illustrate the system. A discrete describing function of a quantizer also is given, and input and output signal waveforms, with illustrative examples, are shown.

Kuo, B. C.↗
NASA NTRS1975

Research study on stabilization and control. Modern sampled-data control theory. Analysis and design of the digital large space telescope system

Dynamic modeling of a low cost single axis LST system and the pointing stability of that system are investigated. The effects of nonlinear friction of the bearings of the reaction wheels, quantization, and sensor noise on the pointing error are covered. In addition, data are given on self sustained oscillations of the system induced by quantization and methods of evaluating attitude error of the digital LST.

Kuo, B. C.↗
NASA NTRS1975

Research study on stabilization and control: Modern sampled-data control theory. Design of the large space telescope system

Conditions of self-sustained oscillations in a two-axis model of the nonlinear LST system are studied. The describing function of the CMG frictional nonlinearity of the LST system is used for the analysis, as well as continuous-data and discrete-data models of the simplified LST control system. A numerical-iterative method is described for the analysis of the two-axis system. Approximation methods and the direct plotting of the stability equation are implemented in the study. It is shown that although the dynamics of the two axes are identical, the amplitudes of self-sustained oscillations in the two axes may in principle be different. Analysis shows that the LST systems are of equal amplitudes but with 180-degree phase shift.

Kuo, B. C.↗
NASA NTRS1974

Research study on stabilization and control modern sampled-data control theory

The methods of continuous and discrete describing function analysis were applied to predicting the existence of self-sustained oscillations in the single-axis model of the large space telescope system with nonlinear control moment gyroscope friction characteristics. It is shown that the stability equations may be solved by a numerical-iterative technique using the describing function analysis, instead of the usual graphical methods. The numerical method is found to be effective in leading to a convergent solution rapidly, with an appropriate guess of the initial condition.

Kuo, B. C.↗
NASA NTRS1974

Modern sampled-data control theory: Design of the Large Space Telescope

This investigation was undertaken to determine the effect of varying the sampling period on the dynamic response of the sampled-data Large Space Telescope (LST) system. A range of sampling periods was recommended based on the criterion that self-sustained oscillations are to be avoided in the LST system. The step responses of the LST system were then investigated when various sampling periods are used. For small sampling periods, the dynamic behavior of the sampled-data system is very similar to that of the continuous-data system. When T is large (but less than 0.25 sec) the overshoot of the step response of the sampled-data becomes greater. However, the dynamic behavior of the sampled-data system may be improved by redesigning the controller. It appears that a sampling period as high as 0.1 second is feasible for the LST system. However, it should be noted that the conclusions are obtained with the existing system model. Other practical considerations such as noise, coupling effects and quantization errors, may restrict the sampling period to a lower value.

Kuo, B. C.↗
NASA NTRS1974

Stability study of the Large Space Telescope /LST/ system with nonlinear CMG gimbal friction

The purpose of the investigation reported upon is to study the existence and characteristics of self-sustained oscillations in the dynamic behavior of the Large Space Telescope (LST) system due to the presence of nonlinear gimbal friction in the control moment gyroscopes (CMGs). A continuous-data single-axis model of the LST is considered. A solid friction model is used to represent CMG gimbal friction. A rigorous mathematical model is derived for use in a continuous describing function analysis. Conditions for self-sustained oscillations are then determined.

Kuo, B. C.↗
NASA NTRS1974

Design of a digital controller for spinning flexible spacecraft

An approach to digital control system design is applied to the analysis and design of a practical onboard digital attitude control system for a class of spinning vehicles characterized by a rigid body and two connected flexible appendages. The approach used is to design a continuous-data control system that will provide a satisfactory system response. Then, using the digital redesign method, a digital controller with onboard digital computer is designed to provide a digital control system whose states are similar to those of the continuous system at sampling instants. The simplicity of application of this approach is indicated by example. The example, using spinning Skylab parameters, is used to substantiate the conclusions.

Kuo, B. C.↗
NASA NTRS1974

Research study on stabilization and control: Modern sampled-data control theory. Continuous and discrete describing function analysis of the LST system

The dynamics of the Large Space Telescope (LST) control system were studied in order to arrive at a simplified model for computer simulation without loss of accuracy. The frictional nonlinearity of the Control Moment Gyroscope (CMG) Control Loop was analyzed in a model to obtain data for the following: (1) a continuous describing function for the gimbal friction nonlinearity; (2) a describing function of the CMG nonlinearity using an analytical torque equation; and (3) the discrete describing function and function plots for CMG functional linearity. Preliminary computer simulations are shown for the simplified LST system, first without, and then with analytical torque expressions. Transfer functions of the sampled-data LST system are also described. A final computer simulation is presented which uses elements of the simplified sampled-data LST system with analytical CMG frictional torque expressions.

Kuo, B. C.↗
NASA NTRS1974

Digital redesign of continuous systems by matching of states at multiple sampling periods

This paper presents a method of digital approximation of a continuous-data system by the matching of states at multiple sampling periods. Two alternate methods are presented; one method samples the states every sampling period, and alters the forward and feedback gains, so as to match the states of the two systems at the end of N sampling periods. The second method requires the sampling of the states every N sampling periods, with the change of gains at each sampling period. An illustrative example using the one-axis dynamics of the Skylab Satellite is presented.

Yackel, R. A.↗