Engineering Papers⌕ Search

Engineering topics

Kisslinger, Kim

Publications and source records attributed to Kisslinger, Kim.

At least 145 records · Page 8

Light-Activated Hybrid Nanocomposite Film for Water and Oxygen Sensing

Oxygen and water vapor sensing properties are investigated in metal-oxide–hybrid polymer nanocomposite thin films generated by infiltration synthesis, which incorporates molecular ZnO into the matrix of SU-8 polymer, a common negative-tone photoresist. The hybrid thin films display 20-fold higher gravimetric responses to oxygen and water vapor than those of control ZnO thin films in the dark. An additional 50–500% enhanced responses are detected under UV irradiation. The overall enhanced gravimetric response in the hybrid film is attributed to the ZnO molecules distributed in the polymer matrix, whereas the UV enhancement is explained by the light-induced, reversible generation of hydrophilic fluoroantimonic acid from triarylsulfonium hexafluoroantimonate photoacids, which leads to the increased surface potential and adsorption energies for oxygen and water. A gravimetric sensor based on a series of ZnO-infiltrated SU-8 films under UV excitation enables 96% accurate classification of water and oxygen environment with sub 10 mTorr detection limits. Furthermore, the results demonstrate UV-induced fully reversible surface hydrophilicity of ZnO/SU-8 hybrid nanocomposites.

36 MATERIALS SCIENCE↗

Achieving High Cycling Rates via In Situ Generation of Active Nanocomposite Metal Anodes

The morphological control of electrochemically deposited metallic anodes, such as Li, Zn, and Mg, under high applied rates is essential for the development of high-energy-density batteries. For transportation applications, maximizing high rates and high energy density is key to attaining viable customer acceleration and range expectations, respectively. In this work, the in situ generation of Mg nanocrystals allowed cycling under high rates (10 mA cm –2 ) and reduced temperature (0 °C) for the very first time. Through operando STEM analysis, we discovered a highly functional SEI, a first of its kind, which enabled continuous deposition and dissolution of Mg without internal shorting. As a result, the unique morphology of the deposited Mg and the functional capability of the SEI are key to future development of practical metallic Mg anodes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tunable surface acoustic wave device using semiconducting MgZnO and piezoelectric NiZnO dual-layer structure on glass

Tunable surface acoustic wave (SAW) devices have attracted considerable interests due to its applications in emerging fields, such as secured wireless communication, adaptive signal processing, and smart sensing systems. We report a dual-input-voltage-controlled tunable SAW built on glass, which uses a ZnO-based dual-layer structure consisting of a piezoelectric Ni- doped ZnO (NZO) and semiconducting Mg-doped ZnO (MZO). The interdigital (IDT) electrodes are buried in the piezoelectric NZO layer to form the delay line for SAW propagation, while the semiconductor MZO layer serves as the channel of a thin film transistor (TFT) to modulate the conductivity. Results show the interface between MZO channel and SiO 2 gate dielectric layer of the TFTT significantly impacts on SAW tuning performances due to Zn diffusion from MZO into SiO 2 . The TFT-SAW device using an ultra-thin MgO layer as interface modification enables SAW frequency tuning of 0.53% under solely V gs control with 0–12 V. The required voltage range is significantly reduced compared regular MZO-NZO TFT-SAW counterpart (Δf/f c ~ 0.25%; V gs –30 to –14 V) without interface modification. With additional control of V ds , the SAW frequency tunability is further expanded from 0.46% to 0.63%. As a result, this dual-input voltage-controlled frequency tuning device on glass is promising for low-voltage, low-cost portable smart sensors and voltage-controlled reconfigurable radio-frequency identification tags.

36 MATERIALS SCIENCE↗

The fabrication of nanoscale Bi 2 Te 3 /Sb 2 Te 3 multilayer thin film-based thermoelectric power chips

In this work, we report our method of fabricating nanoscale multilayered Bi 2 Te 3 /Sb 2 Te 3 thin film-based integrated thermoelectric devices, and detail the voltage and power produced by the device. The multilayered Bi 2 Te 3 /Sb 2 Te 3 thin film was grown via e-beam evaporation; it had 20 alternating Bi 2 Te 3 - and Sb 2 Te 3 -layers, each layer being 1.5 nm thick. We characterized the film using high-resolution transmission electron microscopy (HRTEM), revealing its excellent cross-sectional structure without any obvious interface defects. The Bi 2 Te 3 /Sb 2 Te 3 multilayer films were investigated by synchrotron x-ray scattering. An integrated device including 128×256 thermoelectric elements was fabricated from the multilayered film. An open-circuit voltage of 51 mV and a maximum power of 21 nW were produced from this 30 nm-thick Bi 2 Te 3 /Sb 2 Te 3 multilayer TE device. We found that the nanoscale multilayer structure significantly affects the voltage and power produced. Lastly, the fabrication of the integrated thermoelectric devices is compatible to that of generating standard integrated circuits (ICs), and is scalable for producing higher voltage and power, or achieving solid-state cooling for on-chip applications.

36 MATERIALS SCIENCE↗

High-Quality AZO/Au/AZO Sandwich Film with Ultralow Optical Loss and Resistivity for Transparent Flexible Electrodes

Transparent flexible electrodes are in ever-growing demand for modern stretchable optoelectronic devices, such as, display technologies, solar cells, and smart window. Such sandwich-film-electrodes deposited on polymer substrates are unattainable because of the low quality of the films, inducing a relatively large optical loss and resistivity as well as a difficulty in elucidating the interference behavior of light. In this article, we report a high-quality AZO/Au/AZO sandwich film with excellent optoelectronic performance, e.g., an average transmittance of about 81.7% (including the substrate contribution) over the visible range, a sheet resistance of 5 Ω/sq and a figure-of-merit factor of ~55.1. These values are well ahead of those previously reported for sandwich-film-electrodes. Additionally, the interference behaviors of light modulated by the coat and metal layers have been explored with the employment of transmittance spectra and numerical simulations. In particular, a heater device based on an AZO/Au/AZO sandwich film exhibits high performance such as short response time (~5 s) and uniform temperature field. In conclusion, this work provides a deep insight into the improvement of the film quality of the sandwich electrodes and the design of high-performance transparent flexible devices by the application of a flexible substrate with an atomically smooth surface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dissolution of Pt during Oxygen Reduction Reaction Produces Pt Nanoparticles

The loss of Pt during the oxygen reduction reaction (ORR) affects the performance and economic viability of fuel cells and sensors. Our group previously observed the dissolution of Pt nanoelectrodes at moderately negative potentials during the ORR. Here we report a more detailed study of this process and identify its product. The nanoporous Pt surface formed during the ORR was visualized by AFM and high-resolution SEM, which also showed ~5 nm sized Pt particles on the glass surface surrounding the electrode. Furthermore, the release of these nanoparticles into the solution was confirmed by monitoring their catalytically amplified collisions with a Hg-coated microelectrode used as the tip in the scanning electrochemical microscope (SECM).

36 MATERIALS SCIENCE↗

Interfaces between hexagonal and cubic oxides and their structure alternatives

Multi-layer structure of functional materials often involves the integration of different crystalline phases. The film growth orientation thus frequently exhibits a transformation, owing to multiple possibilities caused by incompatible in-plane structural symmetry. Nevertheless, the detailed mechanism of the transformation has not yet been fully explored. Here we thoroughly probe the heteroepitaxially grown hexagonal zinc oxide (ZnO) films on cubic (001)-magnesium oxide (MgO) substrates using advanced scanning transition electron microscopy, X-ray diffraction and first principles calculations, revealing two distinct interface models of (001) ZnO/(001) MgO and (100) ZnO/(001) MgO. Here we have found that the structure alternatives are controlled thermodynamically by the nucleation, while kinetically by the enhanced Zn adsorption and O diffusion upon the phase transformation. Finally, this work not only provides a guideline for the interface fabrication with distinct crystalline phases but also shows how polar and non-polar hexagonal ZnO films might be manipulated on the same cubic substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ultrahigh Elastic Strain Energy Storage in Metal-Oxide-Infiltrated Patterned Hybrid Polymer Nanocomposites

Modulus of resilience, the measure of a material’s capacity to store and release elastic strain energy, is critical for realizing advanced mechanical actuation technologies in micro/nanoelectromechanical systems. In general, engineering the modulus of resilience is difficult because it requires asymmetrically increasing yield strength and Young’s modulus against their mutual scaling behavior. This task becomes further challenging if it needs to be carried out at the nanometer scale. Here, we demonstrate organic–inorganic hybrid composite nanopillars with one of the highest modulus of resilience per density by utilizing vapor-phase aluminum oxide infiltration in lithographically patterned negative photoresist SU-8. In situ nanomechanical measurements reveal a metal-like high yield strength (~500 MPa) with an unusually low, foam-like Young’s modulus (~7 GPa), a unique pairing that yields ultrahigh modulus of resilience, reaching up to ~24 MJ/m 3 as well as exceptional modulus of resilience per density of ~13.4 kJ/kg, surpassing those of most engineering materials. The hybrid polymer nanocomposite features lightweight, ultrahigh tunable modulus of resilience and versatile nanoscale lithographic patternability with potential for application as nanomechanical components which require ultrahigh mechanical resilience and strength.

36 MATERIALS SCIENCE↗

Enhanced Carbon Dioxide Electroreduction to Carbon Monoxide over Defect-Rich Plasma-Activated Silver Catalysts

Efficient, stable catalysts with high selectivity for a single product are essential if electroreduction of CO 2 is to become a viable route to the synthesis of industrial feedstocks and fuels. A plasma oxidation pre-treatment of silver foil enhances the number of low-coordinated catalytically active sites, which dramatically lowers the overpotential and increases the activity of CO 2 electroreduction to CO. At -0.6 V versus RHE more than 90 % Faradaic efficiency towards CO was achieved on a pre-oxidized silver foil. While transmission electron microscopy (TEM) and operando X-ray absorption spectroscopy showed that oxygen species can survive in the bulk of the catalyst during the reaction, quasi in situ X-ray photoelectron spectroscopy showed that the surface is metallic under reaction conditions. Finally, DFT calculations reveal that the defect-rich surface of the plasma-oxidized silver foils in the presence of local electric fields drastically decrease the overpotential of CO 2 electroreduction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Impacts of Carrier Transport and Deep Level Defects on Delayed Cathodoluminescence in Droop-Mitigating InGaN/GaN LEDs

Prevalent droop mitigation strategies in InGaN-based LEDs require structural and/or compositional changes in the active region but are accompanied by a detrimental reduction in external quantum efficiency (EQE) due to increased Shockley-Read-Hall recombination. Understanding the optoelectronic impacts of structural modifications in InGaN/GaN quantum wells (QW) remains critical for emerging high-power LEDs. In this work, we use a combination of electron microscopy tools along with standard electrical characterization to investigate a wide range of low-droop InGaN/GaN QW designs. We find that chip-scale EQE is uncorrelated with extended well-width fluctuations observed in scanning transmission electron microscopy. Further, we observe delayed cathodoluminescence (CL) response from designs in which calculated band profiles suggest facile carrier escape from individual QWs. Samples with the slowest CL responses also exhibit the lowest EQEs and highest QW defect densities in deep level optical spectroscopy. We propose a model in which the electron beam (i) passivates deep level defect states and (ii) drives charge carrier accumulation and subsequent reduction of the built-in field across the multi-QW active region, resulting in delayed radiative recombination. Finally, we correlate CL rise dynamics with capacitance-voltage measurements and show that certain early-time components of the CL dynamics reflect the open circuit carrier population within one or more QWs.

Zhao, Zhibo↗

Field-assisted sintering and phase transition of ZnS-CaLa 2 S 4 composite ceramics

In the present study, zinc sulfide (ZnS) and calcium lanthanum sulfide (CaLa 2 S 4 , CLS) composite ceramics were consolidated via field-assisted sintering of 0.5ZnS-0.5CLS (volume ratio) composite powders at 800–1050 °C. Through sintering curve analyses and microstructural observations, it was determined that between 800 and 1000 °C, grain boundary diffusion was the main mechanism controlling grain growth for both the ZnS and CLS phases within the composite ceramics. The consolidated composite ceramics were determined to be composed of sphalerite ZnS, wurtzite ZnS and thorium phosphate CLS. The sphalerite-wurtzite phase transition of ZnS was further demonstrated to be accompanied by the formation of stacking faults and twins in the ceramics. Furthermore, it was also found that the addition of the CLS phase improved the indentation hardness of the ceramics relative to pure ZnS by homogeneous dispersion of ZnS and CLS small grains.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Experimental Study of the Detection Limit in Dual-Gate Biosensors Using Ultrathin Silicon Transistors

Dual-gate field-effect biosensors (bioFETs) with asymmetric gate capacitances were shown to surpass the Nernst limit of 59 mV/pH. However, previous studies have conflicting findings on the effect of the capacitive amplification scheme on the sensor detection limit, which is inversely proportional to the signal-to-noise ratio (SNR). In this paper, we present a systematic experimental investigation of the SNR using ultrathin silicon transistors. Our sensors operate at low voltage and feature asymmetric front and back oxide capacitances with asymmetry factors of 1.4 and 2.3. We demonstrate that in the dual-gate configuration, the response of our bioFETs to the pH change increases proportional to the asymmetry factor and indeed exceeds the Nernst limit. Further, our results reveal that the noise amplitude also increases in proportion to the asymmetry factor. We establish that the commensurate increase of the noise amplitude originates from the intrinsic low-frequency characteristic of the sensor noise, dominated by number fluctuation. Finally, these findings suggest that this capacitive signal amplification scheme does not improve the intrinsic detection limit of the dual-gate biosensors.

42 ENGINEERING↗

Strain Coupling of Conversion-type Fe 3 O 4 Thin Films for Lithium Ion Batteries

Lithiation/delithiation induces significant stresses and strains into the electrodes for lithium ion batteries, which can severely degrade their cycling performance. Moreover, this electrochemically induced strain can interact with the local strain existing at solid–solid interfaces. It is not clear how this interaction affects the lithiation mechanism. The effect of this coupling on the lithiation kinetics in epitaxial Fe 3 O 4 thin film on a Nb-doped SrTiO 3 substrate is investigated. In-situ and ex-situ transmission electron microscopy (TEM) results show that the lithiation is suppressed by the compressive interfacial strain. At the interface between the film and substrate, the existence of Li x Fe 3 O 4 rock-salt phase during lithiation consequently restrains the film from delamination. 2D phase-field simulation verifies the effect of strain. This work provides critical insights of understanding the solid–solid interfaces of conversion-type electrodes.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Effects of Residual Solvent Molecules Facilitating the Infiltration Synthesis of ZnO in a Nonreactive Polymer

Infiltration synthesis, the atomic-layer-deposition-based organic–inorganic material hybridization technique that enables unique hybrid composites with improved material properties and inorganic nanostructures replicated from polymer templates, is shown to be driven by the binding reaction between reactive chemical groups of polymers and perfusing vapor-phase material precursors. Here in this paper, we discover that residual solvent molecules from polymer processing can react with infiltrating material precursors to enable the infiltration synthesis of metal oxides in a nonreactive polymer. The systematic study, which combines in situ quartz crystal microgravimetry, polarization-modulated infrared reflection–absorption spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy, shows that the ZnO infiltration synthesis in nominally nonreactive SU-8 polymer is mediated by residual processing solvent cyclopentanone, a cyclic ketone whose Lewis-basic terminal carbonyl group can react with the infiltrating Lewis-acidic Zn precursor diethylzinc (DEZ). In addition, we find favorable roles of residual epoxy rings in the SU-8 film in further assisting the infiltration synthesis of ZnO. Lastly, the discovered rationale not only improves the understanding of infiltration synthesis mechanism, but also potentially expands its application to more diverse polymer systems for the generation of unique functional organic–inorganic hybrids and inorganic nanostructures.

36 MATERIALS SCIENCE↗

Operando Grazing Incidence Small-Angle X-ray Scattering/X-ray Diffraction of Model Ordered Mesoporous Lithium-Ion Battery Anodes

Emergent lithium-ion (Li + ) batteries commonly rely on nanostructuring of the active electrode materials to decrease the Li + ion diffusion path length and to accommodate the strains associated with the insertion and de-insertion of Li + , but in many cases these nanostructures evolve during electrochemical charging–discharging. This change in the nanostructure can adversely impact performance, and challenges remain regarding how to control these changes from the perspective of morphological design. In order to address these questions, operando grazing-incidence small-angle X-ray scattering and X-ray diffraction (GISAXS/GIXD) were used to assess the structural evolution of a family of model ordered mesoporous NiCo 2 O 4 anode films during battery operation. The pore dimensions were systematically varied and appear to impact the stability of the ordered nanostructure during the cycling. For the anodes with small mesopores (≈9 nm), the ordered nanostructure collapses during the first two charge–discharge cycles, as determined from GISAXS. This collapse is accompanied by irreversible Li-ion insertion within the oxide framework, determined from GIXD and irreversible capacity loss. Anodes with larger ordered mesopores (17–28 nm) mostly maintained their nanostructure through the first two cycles with reversible Li-ion insertion. During the second cycle, there was a small additional deformation of the mesostructure. Furthermore, this preservation of the ordered structure lead to significant improvement in capacity retention during these first two cycles; but, a gradual loss in the ordered nanostructure from continuing deformation of the ordered structure during additional charge–discharge cycles leads to capacity decay in battery performance. We translate these multiscale operando measurements provide insight into how changes at the atomic scale (lithium insertion and de-insertion) to the nanostructure during battery operation. Moreover, small changes in the nanostructure can build up to significant morphological transformations that adversely impact battery performance through multiple charge–discharge cycles.

25 ENERGY STORAGE↗