Engineering Papers⌕ Search

Engineering topics

Kim, J.

Publications and source records attributed to Kim, J..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Satellite Geopotential Anomaly Constraints for the Crust of the Greenland-Iceland Region

Satellite magnetometer observations of the Greenland-Iceland region compare quite well with lower altitude data. The satellite magnetic data suggest magnetically enhanced crust was emplaced by the Iceland Plume. Crustal thicknesses, which may be more than 30 km for the Greenland-Scotland Ridge, were obtained from inversion of the compensating terrain gravity effects that were estimated by spectral correlation analysis of the free-air gravity anomalies and terrain gravity effects. Regional magnetic anomaly maxima overlie possible thickened crust from eastern Iceland to the Greenland Coast. The Iceland-Faroe Ridge may involve thinner crust than the Greenland-Iceland portion of the Greenland-Scotland Ridge. The gravity derived crustal model exceeds a 0.7 correlation with available seismic estimates. In thermally active areas our gravity Moho estimates are systematically deeper than the seismic estimates suggesting local density reductions of the underlying lower crust/upper mantle. In south central Greenland, on the other hand, the gravity Moho estimates are shallower than seismic estimates to suggest a local enhancement of the lower crust/upper mantle density. The dichotomous crust of the Greenland-Iceland and Iceland-Faroe Ridges suggests unequal crustal development by the Iceland Plume and the Mid-Atlantic Ridge, where more crustal material may have been contributed to the North Atlantic Plate than the Eurasian Plate. A new thermal modeling scheme based on Poisson's relation between point pole gravity and thermal potentials allows estimation of magnetic crustal thicknesses. Subsequent magnetic anomaly inversion for susceptibility contrasts infers crustal development of the Greenland-Scotland Ridge by temporally variable pulses in plume strength.

vonFrese, R. R.↗
NASA NTRS2004

Controller of the Laser Interferometer Space Antenna

The Laser Interferometer Space Antenna mission is a planned gravitational wave detector consisting of three spacecraft in heliocentric orbit. Laser interferometry is used to measure distance fluctuations between test masses aboard each spacecraft to the picometer level over a 5 million kilometer separation. The Disturbance Reduction System comprises the pointing and positioning control of the spacecraft, electrostatic suspension control of the test masses, and point-ahead and acquisition control. This paper presents a control architecture and design for the Disturbance Reduction System to meet the stringent pointing and positioning requirements. Simulations are performed to demonstrate the feasibility of the proposed architecture.

Hyde, T. T.↗
NASA NTRS2002

A Statistical Analysis of Laser Ablated Ba(Sub 0.50)Sr(Sub 0.50)TiO(Sub 3)/LaAlO(Sub 3) Films for Microwave Applications

The NASA Glenn Research Center is constructing a 616 element scanning phased array antenna using thin film Ba(sub x)Sr(sub 1-x)TiO(sub 3) based phase shifters. A critical milestone is the production of 616 identical phase shifters at 19 GHz with [asymptotically equal to]4 dB insertion loss and at least 337.5 deg phase shift with 3 percent bandwidth. It is well known that there is a direct relationship between dielectric tuning and loss due to the Kramers-Kronig relationship and that film crystallinity and strain, affected by the substrate template, play an important role. Ba(sub 0.50)Sr(sub 0.50)TiO (sub 3) films, nominally 400 nm thick, were deposited on 48 0.25 mm thick, 5 cm diameter LaAlO(sub 3) wafers. Although previous results suggested that Mn-doped films on MgO were intrinsically superior in terms of phase shift per unit loss, for this application phase shift per unit length was more important. The composition was selected as a compromise between tuning and loss for room temperature operation (e.g. crystallinity progressively degrades for Ba concentrations in excess of 30 percent). As a prelude to fabricating the array, it was necessary to process, screen, and inventory a large number of samples. Variable angle ellipsometry was used to characterize refractive index and film thickness across each wafer. Microstructural properties of the thin films were characterized using high resolution X-ray diffractometry. Finally, prototype phase shifters and resonators were patterned on each wafer and RE probed to measure tuning as a function of dc bias voltage as well as peak (0 field) permittivity and unloaded Q. The relationship among film quality and uniformity and performance is analyzed. This work presents the first statistically relevant study of film quality and microwave performance and represents a milestone towards commercialization of thin ferroelectric films for microwave applications.

Ferroelectric thin films↗
NASA NTRS2001

Investigation of Nitride Morphology After Self-Aligned Contact Etch

Self-Aligned Contact (SAC) etch has emerged as a key enabling technology for the fabrication of very large-scale memory devices. However, this is also a very challenging technology to implement from an etch viewpoint. The issues that arise range from poor oxide etch selectivity to nitride to problems with post etch nitride surface morphology. Unfortunately, the mechanisms that drive nitride loss and surface behavior remain poorly understood. Using a simple langmuir site balance model, SAC nitride etch simulations have been performed and compared to actual etched results. This approach permits the study of various etch mechanisms that may play a role in determining nitride loss and surface morphology. Particle trajectories and fluxes are computed using Monte-Carlo techniques and initial data obtained from double Langmuir probe measurements. Etched surface advancement is implemented using a shock tracking algorithm. Sticking coefficients and etch yields are adjusted to obtain the best agreement between actual etched results and simulated profiles.

Hwang, Helen H.↗
NASA NTRS2000

Fiber size and myosin phenotypes of selected rhesus lower limb muscles after a 14-day spaceflight

Muscle biopsies were taken from the rhesus (Macaca mulatta) soleus (Sol, a slow ankle extensor), medial gastrocnemius (MG, a fast ankle extensor), tibialis anterior (TA, a fast ankle flexor), and vastus lateralis (VL, a fast knee extensor) muscles in vivarium controls (n=5) before and after either a 14-day spaceflight (Bion 11, n=2) or a 14-day ground-based flight simulation (n=3). Myosin heavy chain (MHC) composition (gel electrophoresis), fiber type distribution (immunohistochemistry), and fiber size were determined. Although there were no significant changes, each muscle showed trends towards adaptation.

NASA Discipline Musculoskeletal↗
NASA NTRS1999

Investigation of Near Shannon Limit Coding Schemes

Turbo codes can deliver performance that is very close to the Shannon limit. This report investigates algorithms for convolutional turbo codes and block turbo codes. Both coding schemes can achieve performance near Shannon limit. The performance of the schemes is obtained using computer simulations. There are three sections in this report. First section is the introduction. The fundamental knowledge about coding, block coding and convolutional coding is discussed. In the second section, the basic concepts of convolutional turbo codes are introduced and the performance of turbo codes, especially high rate turbo codes, is provided from the simulation results. After introducing all the parameters that help turbo codes achieve such a good performance, it is concluded that output weight distribution should be the main consideration in designing turbo codes. Based on the output weight distribution, the performance bounds for turbo codes are given. Then, the relationships between the output weight distribution and the factors like generator polynomial, interleaver and puncturing pattern are examined. The criterion for the best selection of system components is provided. The puncturing pattern algorithm is discussed in detail. Different puncturing patterns are compared for each high rate. For most of the high rate codes, the puncturing pattern does not show any significant effect on the code performance if pseudo - random interleaver is used in the system. For some special rate codes with poor performance, an alternative puncturing algorithm is designed which restores their performance close to the Shannon limit. Finally, in section three, for iterative decoding of block codes, the method of building trellis for block codes, the structure of the iterative decoding system and the calculation of extrinsic values are discussed.

Kwatra, S. C.↗
NASA NTRS1999

Boiling Heat Transfer Measurements on Highly Conductive Surfaces Using Microscale Heater and Temperature Arrays

Two systems have been developed to study boiling heat transfer on the microscale. The first system utilizes a 32 x 32 array of diodes to measure the local temperature fluctuations during boiling on a silicon wafer heated from below. The second system utilizes an array of 96 microscale heaters each maintained at constant surface temperature using electronic feedback loops. The power required to keep each heater at constant temperature is measured, enabling the local heat transfer coefficient to be determined. Both of these systems as well as some preliminary results are discussed.

Kim, J.↗
NASA NTRS1998

Design, Construction, and Qualification of a Microscale Heater Array for Use in Boiling Heat Transfer

Boiling heat transfer is an efficient means of heat transfer because a large amount of heat can be removed from a surface using a relatively small temperature difference between the surface and the bulk liquid. However, the mechanisms that govern boiling heat transfer are not well understood. Measurements of wall temperature and heat flux near the wall would add to the database of knowledge which is necessary to understand the mechanisms of nucleate boiling. A heater array has been developed which contains 96 heater elements within a 2.5 mm square area. The temperature of each heater element is held constant by an electronic control system similar to a hot-wire anemometer. The voltage that is being applied to each heater element can be measured and digitized using a high-speed A/D converter, and this digital information can be compiled into a series of heat-flux maps. Information for up to 10,000 heat flux maps can be obtained each second. The heater control system, the A/D system and the heater array construction are described in detail. Results are presented which show that this is an effective method of measuring the local heat flux during nucleate and transition boiling. Heat flux maps are obtained for pool boiling in FC-72 on a horizontal surface. Local heat flux variations are shown to be three to six times larger than variations in the spatially averaged heat flux.

Rule, T. D.↗
NASA NTRS1997

Cabauw Experimental Results from the Project for Intercomparison of Land-Surface Parameterization Schemes

In the Project for Intercomparison of Land-Surface Parameterization Schemes phase 2a experiment, meteorological data for the year 1987 from Cabauw, the Netherlands, were used as inputs to 23 land-surface flux schemes designed for use in climate and weather models. Schemes were evaluated by comparing their outputs with long-term measurements of surface sensible heat fluxes into the atmosphere and the ground, and of upward longwave radiation and total net radiative fluxes, and also comparing them with latent heat fluxes derived from a surface energy balance. Tuning of schemes by use of the observed flux data was not permitted. On an annual basis, the predicted surface radiative temperature exhibits a range of 2 K across schemes, consistent with the range of about 10 W/m in predicted surface net radiation. Most modeled values of monthly net radiation differ from the observations by less than the estimated maximum monthly observational error (+/- 10 W/sq m). However, modeled radiative surface temperature appears to have a systematic positive bias in most schemes; this might be explained by an error in assumed emissivity and by models' neglect of canopy thermal heterogeneity. Annual means of sensible and latent heat fluxes, into which net radiation is partitioned, have ranges across schemes of 30 W/sq m and 25 W/sq m, respectively. Annual totals of evapotranspiration and runoff, into which the precipitation is partitioned, both have ranges of 315 mm. These ranges in annual heat and water fluxes were approximately halved upon exclusion of the three schemes that have no stomatal resistance under non-water-stressed conditions. Many schemes tend to underestimate latent heat flux and overestimate sensible heat flux in summer, with a reverse tendency in winter. For six schemes, root-mean-square deviations of predictions from monthly observations are less than the estimated upper bounds on observation errors (5 W/m for sensible beat flux and 10 W/m for latent heat flux). Actual runoff at the site is believed to be dominated by vertical drainage to ground water, but several schemes produced significant amounts of runoff as overland flow or interflow. There is a range across schemes of 184 mm (40% of total pore volume) in the simulated annual mean root-zone soil moisture. Unfortunately, no measurements of soil moisture were available for model evaluation. A theoretical analysis suggested that differences in boundary conditions used in various schemes are not sufficient to explain the large variance in soil moisture. However, many of the extreme values of soil moisture could be explained in terms of the particulars of experimental setup or excessive evapotranspiration.

Chen, Tian Hong↗
NASA NTRS1995

Modeling and numerical simulation of microwave pulse propagation in air breakdown environment

It is shown that ionization occurs wherever the field intensity of the pulse exceeds the local breakdown threshold field of the background air. The produced plasma then attenuates the pulse and gives rise to a tail erosion phenomenon that plays the primary role in limiting the energy transfer of the pulse from source to destination. A theoretical model describing the propagation of an intense microwave pulse in an air breakdown environment is developed that includes the possible focusing effect introduced by either using phase array antennas or the other arrangements. The self-consistent description of the propagation process is provided by a set of two modal equations. These include a continuity equation (Poynting's equation) for the energy density of the pulse and a rate equation of the electron density. A forward wave approximation is used to simplify Poynting's equation, and a semiempirical formula is used for the ionization frequency, nu(sub i). This frequency provides the coupling between the two modal equations, and is used to express the electron rate equation explicitly. In terms of the relevant parameters of the atmosphere, these two equations are normalized for numerical analysis of pulse propagation in the atmosphere. The dependencies of the propagation characteristics of the pulse on intensity, frequency, width, and shape of the pulse are determined. The numerical simulations lead to a useful empirical relation p(exp 3)w = alpha = constant, where p and w are the incident power and width of the pulse and alpha depends on the percentage of pulse energy transferred from the source point to a destined position. The density distribution of the pulse's self-generated plasma is also evaluated. The results also show that for ionization caused by a single unfocused microwave pulse transmitted upwards from the ground, the maximum electron density produced at, for example, 50 km altitude is limited by the tail erosion effect to below 10(exp 6) cm(exp -3). Repetitive pulse and focused beam approaches are also examined. Both approaches can increase the maximum electron density by no more than an order of magnitude. A scheme using two obliquely propagating pulses intersecting at the destined height, e.g. 50 km, is considered. It is shown that the electron density generated at the lowest intersecting position can easily reach a value of 6.6 x 10(exp 8) cm(exp -3), which is considered to be high enough for artificial ionospheric mirror (AIM) application.

Kim, J.↗
NASA NTRS1995

Reynold-Number Effects on Near-Wall Turbulence

The Reynolds stress budget in a full developed turbulent channel flow for three Reynolds numbers (Re = 180,395,590) are used to investigate the near wall scaling of various turbulence quantities. We find that as the Reynolds number increases, the extent of the region where the production of the kinetic energy is equal to the dissipation increases. At the highest Reynolds number the region of equilibrium extends from y+ - 120 to y+ = 240. As the Reynolds number increases, we find that wall scaling collapses the budgets for the streamwise fluctuating component, but the budgets for the other two components show Reynolds number dependency.

Mansour, N. N.↗
NASA NTRS1994

Using Virtual Reality for Science Mission Planning: A Mars Pathfinder Case

The Mars Pathfinder Project GDS Team has designed software that integrates virtual reality technology with existing JPL Navigational Ancillary Information Facilities (NAIF) and image processing capabilities. The result is an interactive, workstation-based application software that provides a high resolution 3-dimensional stereo display of Mars as if it were viewed through the lander camera. This paper describes the architecture and characteristics of this science mission planning software and discusses possible uses of this software by other planetary missions.

virtual↗
NASA NTRS1993

Isotropy of the small scales of turbulence at low Reynolds number

Spectral local isotropy tests are applied to direct numerical simulation data, mainly at the centerline of a fully developed turbulent channel flow. Despite the small Reynolds number of the simulation, the high-wavenumber behavior of velocity and vorticity spectra is consistent with local isotropy. This consistency is verified by the relationship between streamwise wavenumber spectra and spanwise wavenumber spectra. The high-wavenumber behavior of the pressure spectrum is also consistent with local isotropy and compares favorably with the calculation of Batchelor (1951), which assumes isotropy and joint normality of the velocity field at two points in space. The latter assumption is validated by the shape but not the magnitude of the quadruple correlation of the streamwise velocity fluctuation at small separations. There is only partial support for local spectral isotropy away from the centerline as the magnitude of the mean strain rate increases.

Kim, J.↗
NASA NTRS1993

Photosynthesis and stomatal conductance related to reflectance on the canopy scale

Field measurements of carbon dioxide and water vapor fluxes were analyzed in conjunction with reflectances obtained from a helicopter-mounted Modular Multiband Radiometer at a grassland study site during the First International Satellite Land Surface Climatology Project Field Experiment. These measurements are representative of the canopy scale and were made over a range of meteorological and soil moisture conditions during different stages in the annual life cycle of the prairie vegetation, and thus provide a good basis for investigating hpotheses/relationships potentially useful in remote sensing applications. We tested the hypothesis (Sellers, 1987) that the simple ratio vegetation index should be near-linearly related to the derivatives of the unstressed canopy stomatal conductance and the unstressed canopy photosynthesis with respect to photosynthetically active radiation. Even though there is some scatter in our data, the results seem to support this hypothesis.

Verma, S. B.↗
NASA NTRS1993

On the measurement of lateral velocity derivatives in turbulent flows

Direct numerical simulation data for the lateral velocity derivative delta(u)/delta(y) at the centerline of a fully developed turbulent channel flow provide reasonable support for Wyngaard's analysis of the error involved in measuring this quantity using parallel hot wires. Numerical data in the wall region of the channel flow also provide a useful indication of how to select the separation between the wires. Justification for this choice is obtained by comparing several measured statistics of delta(u)/delta(y) with the corresponding numerical data.

Antonia, R. A.↗