Engineering Papers⌕ Search

Engineering topics

Kahle, A. B.

Publications and source records attributed to Kahle, A. B..

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Evaluation of LANDSAT MSS vs TM simulated data for distinguishing hydrothermal alteration

The LANDSAT Follow-On (LFO) data was simulated to demonstrate the mineral exploration capability of this system for segregating different types of hydrothermal alteration and to compare this capability with that of the existing LANDSAT system. Multispectral data were acquired for several test sites with the Bendix 24-channel MSDS scanner. Contrast enhancements, band ratioing, and principal component transformations were used to process the simulated LFO data for analysis. For Red Mountain, Arizona, the LFO data allowed identification of silicified areas, not identifiable with LANDSAT 1 and 2 data. The improved LFO resolution allowed detection of small silicic outcrops and of a narrow silicified dike. For Cuprite - Ralston, Nevada, the LFO spectral bands allowed discrimination of argillic and opalized altered areas; these could not be spectrally discriminated using LANDSAT 1 and 2 data. Addition of data from the 1.3- and 2.2- micrometer regions allowed better discriminations of hydrothermal alteration types.

Abrams, M. J.↗
NASA NTRS1977

Construction and interpretation of a digital inertia image

An image representing the thermal inertia in the vicinity of Pisgah Crater and Lavic Lake in Southern California has been generated from visible, near IR, and thermal images taken from aircraft. Construction of the thermal inertia image required radiometric calibration and geometric rectification of the acquired images as well as registration to a topographic map. The Kahle thermal model used in the construction of the thermal inertia image requires specification of albedo, topographic slope and slope azimuth, diurnal temperature range and local meteorological conditions. Albedo information was derived from the visible image; digital topographic information was computed from digitized stereo aerial photographs; and thermal ranges were calculated by subtracting the predawn from the afternoon thermal image data. Our computed values of thermal inertia were in close agreement with published values for similar surface materials. Thermal inertia provides complementary information to conventional images of reflected solar radiation for use in lithologic mapping.

Gillespie, A. R.↗
NASA NTRS1977

A simple thermal model of the earth's surface for geologic mapping by remote sensing

Thermal inertia of the earth's surface can be used in geologic mapping as a complement to surface reflectance data as provided by Landsat. Thermal inertia cannot be determined directly but must be inferred from radiation temperature measurements (by thermal IR sensors) made at various times in the diurnal cycle, combined with a model of the surface heating processes. A model is developed which differs from those created previously for this purpose, because it includes sensible and latent heating. Tests of this model using field data indicate that it accurately determines the surface heating. When the model is used with field measurements of meteorological variables and is combined with remotely sensed temperature data, a thermal inertia image can be produced.

Kahle, A. B.↗
NASA NTRS1977

JPL field measurements at the Finney County, Kansas, test site, October 1976: Meteorological variables, surface reflectivity, surface and subsurface temperatures

Data collected at the Finney County, Kansas test site as part of the Joint Soil Moisture Experiment (JSME) are presented here, prior to analysis, to provide all JSME investigators with an immediate source of primary information. The ground-truth measurements were taken to verify and complement soil moisture data taken by microwave and infrared sensors during aircraft overflights. Measurements were made of meteorological variables (air speed, temperature, relative humidity, and rainfall), surface reflectivity, and temperatures at and below the surface.

Kahle, A. B.↗
NASA NTRS1976

Thermal inertia imaging - A new geologic mapping tool

A thermal model of the earth's surface has been developed and used to determine the thermal inertia of a test site in the Mojave Desert, California. The model, which includes meteorological heating terms as well as radiation and conduction heating terms, is used with remotely sensed surface temperature and reflectance data to determine the thermal inertia of the surface materials at the test site. The thermal inertia is displayed in image form, and can aid in the differentiation of the various lithologic materials in the test site. Since this thermal property is representative of the upper several cm of the surface, it complements visible and reflected near-IR image data.

Kahle, A. B.↗
NASA NTRS1975

The detection of geothermal areas from Skylab thermal data

Skylab-4 X-5 thermal data of the geysers area was analyzed to determine the feasibility of using midday Skylab images to detect geothermal areas. The hottest ground areas indicated on the Skylab image corresponded to south-facing barren or sparsely vegetated slopes. A geothermal area approximately 15 by 30 m coincided with one of the hottest areas indicated by Skylab. This area could not be unambiguously distinguished from the other areas which are believed to be hotter than their surroundings as a result of their topography, and micrometeorological conditions. A simple modification of a previous thermal model was performed and the predicted temperatures for the hottest slopes using representative values was in general agreement with the observed data. It is concluded that data from a single midday Skylab pass cannot be used to locate geothermal areas.

Siegal, B. S.↗
NASA NTRS1975

Detectability of geothermal areas using Skylab X-5 data

The results are presented of a study which was undertaken to determine if data from a single near-noon pass of Skylab could be used to detect geothermal areas. The size and temperature requirements for a geothermally heated area to be seen by Skylab S-192 MSS X-5 thermal sensor were calculated. This sensor obtained thermal data with the highest spatial resolution of any nonmilitary satellite system. Only very large hot areas could be expected to be unambiguously recognized with a single data set from this instrument. The study area chosen was The Geysers geothermal field in Sonoma County, California, the only geothermal area of significant size scanned by Skylab. Unfortunately, 95% of the Skylab thermal channel data was acquired within 3 hours of local noon. For The Geysers area only daytime X-5 data were available. An analysis of the thermal channel data (10.2 to 12.5 um) revealed that ground temperatures determined by Skylab were normally distributed. No anomalous hot spots were apparent. Computer enhancement techniques were used to delineate the hottest 100 and 300 ground areas (pixel, 75 m by 75 m) within the study region. It was found that the Skylab MSS with the X-5 thermal detector does not have sufficient spatial resolution to locate unambiguously from daytime data any but the largest and hottest convectively created geothermal features, which in general are prominent enough to have been previously recognized.

Siegal, B. S.↗
NASA NTRS1975

Thermal inertia mapping

A thermal model of the earth's surface has been developed and used to determine the thermal inertia of a test site in the Mojave Desert, California. The model, which includes meteorological heating terms as well as radiation and conduction heating terms, is used with remotely sensed surface temperature data to determine thermal inertia of materials. The thermal inertia is displayed in image form, and can aid in the differentiation of the various lithologic materials in the test site.

Kahle, A. B.↗