Engineering Papers⌕ Search

Engineering topics

Justin Littell

Publications and source records attributed to Justin Littell.

30 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Simulation and Analysis of NASA Lift Plus Cruise eVTOL Crash Test

The National Aeronautics and Space Administration (NASA) will perform a full-scale crash test of a representative electric vertical take-off and landing (eVTOL) fuselage in November 2022. The test article is a carbon-composite fuselage cabin section of the six-passenger lift plus cruise (LPC) eVTOL design concept which was created by NASA to advance understanding of eVTOL propulsion, noise, and safety. The test will consist of impacting the fuselage cabin section onto a concrete surface with a combined horizontal and vertical velocity approximating a severe but survivable crash landing for this vehicle design. Data generated from this test will be used to inform eVTOL crashworthiness regulation development, evaluate the use of energy absorbing concepts within vehicle design, and validate finite element model (FEM) techniques used in crashworthiness predictions. The cabin section response will be evaluated using structural instrumentation, anthropometric test devices (ATDs), and high-speed photogrammetry. This study will compare pre-test FEM predictions to test results to quantify the capability of these tools to predict crashworthiness of the carbon-composite eVTOL airframe.

Crashworthiness↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRSDate not supplied

A Summary of Test Results from a NASA Lift + Cruise eVTOL Crash Test

On November 9, 2022, the National Aeronautics and Space Administration (NASA) conducted a full-scale crash test of the NASA Lift+Cruise (LPC) reference vehicle at the NASA Langley Research Center Landing and Impact Research Facility (LandIR) under combined vertical and horizontal impact conditions to simulate a severe but survivable crash. The LPC test article is a carbon-composite skin/frame structure design, developed and fabricated for the cabin section only. The test utilized various configurations of seats and Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) intended to encompass a variety of occupant conditions. In addition, an in-house developed energy absorbing subfloor was utilized for the evaluation of load attenuation. Overhead mass was simulated using attached lifting hardware and other systems were simulated using ballast mass. The test article impacted the ground with velocities of 38.1 ft/s horizontal and 31.4 ft/s vertical. During the first approximately 38 milliseconds (ms), the cabin section experienced a large amount of acceleration on the belly which was attenuated by the subfloor structures and seats. Over the next approximately 160 ms, the test article experienced failure in the a-, b- and c-pillars, leading to a partial collapse of the overhead structure. Test data was collected on the belly, floors, seats, overhead mass, and tail. In addition, there was high speed full-field digital image correlation analysis data collected on the port side skin surface. Collected ATD data showed that the ATDs seated in the energy absorbing seats experienced loads at limits below the those in current regulations. Even without an energy absorbing seat, the energy absorbing subfloors crushed as intended, and limited the load on the large 95 th percentile ATD to 10% over suggested limits. The collapse of the roof did affect the 95 th percentile ATD, which showed high neck loading values due to head contact, whereas survivable volume was maintained for the other ATDs. While the energy absorbing subfloor and energy absorbing seats both contributed to occupant load attenuation, further optimization is suggested to increase their robustness.

evtol↗
NASA NTRSDate not supplied

Simulation and Analysis of NASA Lift Plus Cruise eVTOL Crash Test

The National Aeronautics and Space Administration (NASA) will perform a full-scale crash test of a representative electric vertical take-off and landing (eVTOL) fuselage in November 2022. The test article is a carbon-composite fuselage cabin section of the six-passenger lift plus cruise (LPC) eVTOL design concept which was created by NASA to advance understanding of eVTOL propulsion, noise, and safety. The test will consist of impacting the fuselage cabin section onto a concrete surface with a combined horizontal and vertical velocity approximating a severe but survivable crash landing for this vehicle design. Data generated from this test will be used to inform eVTOL crashworthiness regulation development, evaluate the use of energy absorbing concepts within vehicle design, and validate finite element model (FEM) techniques used in crashworthiness predictions. The cabin section response will be evaluated using structural instrumentation, anthropometric test devices (ATDs), and high-speed photogrammetry. This study will compare pre-test FEM predictions to test results to quantify the capability of these tools to predict crashworthiness of the carbon-composite eVTOL airframe.

Crashworthiness↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRSDate not supplied

An Overview of the NASA Lift+Cruise eVTOL Crash Test

Introduction – NASA RVLT Project Impact Dynamics / Crash Safety Task - Task Objective: “To improve the crashworthiness and impact safety of Urban Air Mobility (UAM) vehicle and provide data to simplify the certification process. Efforts will include development of validated computational models of these vehicles, as well as other impacting bodies such as birds and drones. Efforts will also focus on developing and evaluating energy absorbing and crush properties of emerging and non-traditional composite materials and processes. Finally, occupant protection will be addressed using computational models and physical assets as it pertains to all rotorcraft environments.” - Problem Statement: “There currently is a lack of data for requirements regarding the crashworthy performance of UAM vehicles and impact loads generated by a bird strike. To address this technology gap, NASA will develop test guidelines, adopt modeling methodologies demonstrating capability for ‘certification by analysis’, acquire vehicle and occupant data on full-scale representative vehicles, and provide data/guidance to consensus standards organizations and the UAM community.” - 4 Main focus points - The investigation of occupant injury using physical and computational assets - The development of energy absorbing technology - The generation of data from sub- and full-scale crash test data - The execution of advanced finite element modelling techniques

evtol↗
NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗
NASA NTRSDate not supplied

Analysis of a Landing System for Planetary Payloads Utilizing Passive Energy Absorbing Composite Structure

Delivery of a payload from space to a planetary surface currently requires the development of an application specific landing system to protect the payload from forces imparted during impact with the planet surface. Often, active energy attenuating systems such as retro-rockets, deployable parachutes, and airbags are utilized within these landing systems to reduce landing impact energy. Unfortunately, these active systems come at a cost; active energy attenuating systems are susceptible to system faults which may limit or completely negate their energy attenuating capability. Additionally, components needing to be stowed such as fuel, parachutes, and airbags increase design complexity, cost, and weight. To overcome these limitations, this study examines the potential of passive energy attenuation through energy absorbing structural design and composite materials to mitigate landing loads for small payload planetary delivery. Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted extensive research into developing energy absorbing structures and components for the attenuation of impact energy under various loading conditions including aircraft crash and spacecraft impact. The current study leverages this research to design a lightweight planetary delivery system which utilizes unique outer mold line (OML) geometry and passive energy absorbing structural design to limit landing loads across potential planetary surface environments. The OML geometry is designed to control impact orientation and provide self-righting capabilities for slopped impact surfaces. The internal structure is composed of composite material structures arranged to provide energy absorption which is robust to impact angle and impact velocity. The developed planetary delivery design concept will be evaluated using finite element (FE) model analysis. Simulations of landing impacts with representative soil surface environments will be used to characterize the energy absorbing capabilities of the landing system. Sensitivity of predicted impact force to landing environment, impact angle, and impact velocity will be assessed to identify capabilities and limitations of the initial structural design. Results will be used to determine the feasibility of a lightweight composite structure to passively absorb landing energy for robust planetary payload delivery.

Crashworthiness↗