Engineering Papers⌕ Search

Engineering topics

Jones, R. T.

Publications and source records attributed to Jones, R. T..

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Transonic wind-tunnel tests of an F-8 airplane model equipped with 12 and 14-percent thick oblique wings

An experimental investigation was conducted in the Ames 14-foot transonic wind tunnel to study the aerodynamic performance and stability characteristics of a 0.087-scale model of an F-8 airplane fitted with an oblique wing. Two elliptical planform (axis ratio = 8:1) wings, each having a maximum thickness of 12 and 14 percent, were tested. Longitudinal stability data were obtained with no wing and with each of the two wings set at sweep angles of 0, 45, and 60 deg. Lateral directional stability data were obtained for the 12 percent wing only. Test Mach numbers ranged from 0.6 to 1.2 in the unit Reynolds number range from 11.2 to 13.1 million per meter. Angles of attack were between -6 and 22 deg at zero sideslip. Angles of sideslip were between -6 and +6 deg for two angles of attack, depending upon the wing configuration.

Smith, R. C.↗
NASA NTRS1974

Aircraft design for flight below the sonic boom speed limit

The avoidance of sonic booms places a constraint on aircraft design and can lead to unusual new configurations. From a comparison among several candidate designs, it is shown that an oblique-wing aircraft offers many advantages when structure, stability, flight efficiency, and airport noise are considered jointly.

Jones, R. T.↗
NASA NTRS1974

Transonic transport wings - Oblique or swept

A comparative evaluation of fixed-geometry and variable-sweep wing designs, a fixed delta wing, and oblique wings with a single body or two bodies suggests that an oblique wing is preferable in a transonic transport aircraft in terms of gross weight, fuel consumption, and aircraft noise, and also shows an acceptable aeroelastic stability. Further studies are, however, needed to develop the full potential of the oblique-wing concept, including its economic implications.

Jones, R. T.↗
NASA NTRS1974

Transonic transport wings - Oblique or swept

Oblique-wing twin- and single-fuselage transonic transport models were wind tunnel tested and showed superior aerodynamic efficiency to that of fixed-swept-wing, variable-sweep-wing, and delta-wing configurations similarly tested. The oblique-wing airplane had the smallest gross weight and lowest fuel consumption; it could achieve lower noise levels than swept- and delta-wing aircraft by engine-nacelle treatment; and it was aeroelastically less stable than a sweptback wing but more stable than a swept-forward wing. Graphite-epoxy met stability requirements without additional stiffening, whereas aluminum needed some additional stiffness. Further studies are called for to develop the full potential of the oblique-wing concept.

Jones, R. T.↗
NASA NTRS1973

Program user's manual for optimizing the design of a liquid or gaseous propellant rocket engine with the automated combustor design code AUTOCOM

This computer program manual describes in two parts the automated combustor design optimization code AUTOCOM. The program code is written in the FORTRAN 4 language. The input data setup and the program outputs are described, and a sample engine case is discussed. The program structure and programming techniques are also described, along with AUTOCOM program analysis.

Reichel, R. H.↗
NASA NTRS1973

Dual-fuselage aircraft having yawable wing and horizontal stabilizer

An aircraft configuration consisting of a pair of fuselages parallel to each other and connected by a main wing and a horizontal stabilizer which pivot on the fuselages is described. The pivotal attachment allows the wing to be yawed relative to the fuselages for high speed flight while at the same time spreading the weight and volume distribution of the aircraft along the direction of flight. The main wing is curved upward at the tips to compensate for any roll tendencies caused by its yawed position.

Jones, R. T.↗
NASA NTRS1973

Wind tunnel tests of an F-8 airplane model equipped with an oblique wing

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to study the lift, drag and stability characteristics of a 0.087-scale model of an operational airplane fitted with an oblique wing. The model wing was of elliptical planform with an unswept aspect ratio of 12.7 and a thickness of 10 percent. All other external geometric features of the model were scaled to the basic full size operational airplane with the engine inlet faired closed. Longitudinal and lateral-directional stability data were obtained with the wing at sweep angles of 0 deg, 45 deg and 60 deg Test Mach numbers ranged from 0.6 to 1.4 deg Angles of attack were between minus 4 deg and 8 deg at zero sideslip. Angles of sideslip were between plus and minus 4 degrees for two angles of attack depending upon the wing configuration. Tests were conducted at a Reynolds number of 6 million per foot except for a few runs when balance capacity limited the Reynolds number to 4 million per foot.

Graham, L. A.↗
NASA NTRS1973

An experimental investigation of three oblique-wing and body combinations at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to determine the aerodynamic characteristics of three oblique high aspect ratio wings in combination with a high fineness-ratio Sears-Haack body. The three wings had the same elliptical planform and base line curvature but had different airfoil sections. One wing had an airfoil section designed to have a lift coefficient of 1.0 at a Mach number of 0.7, another to have shock-free supersonic flow over the upper surface, and the other to have a lift coefficient of 1.3 at a Mach number of 0.6. Longitudinal and lateral-directional stability data were obtained at wing yaw angles of 0 deg, 45 deg, 50 deg, and 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 7 deg and 9 deg. Reynolds numbers for the study were 4 and 6 million per foot. Flow-visualization studies were made to examine the nature of the flow on the wing surfaces. Notable differences were found in the aerodynamic characteristics of the three wing-body combinations, particularly in the lateral-directional characteristics.

Graham, L. A.↗
NASA NTRS1972

Optimizing a liquid propellant rocket engine with an automated combustor design code (AUTOCOM)

A procedure for automatically designing a liquid propellant rocket engine combustion chamber in an optimal fashion is outlined. The procedure is contained in a digital computer code, AUTOCOM. The code is applied to an existing engine, and design modifications are generated which provide a substantial potential payload improvement over the existing design. Computer time requirements for this payload improvement were small, approximately four minutes in the CDC 6600 computer.

Hague, D. S.↗
NASA NTRS1972

An experimental investigation of an oblique-wing and body combination at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot wind tunnel to determine the aerodynamic characteristics of an oblique high aspect ratio wing in combination with a high fineness-ratio Sears-Haack body. Longitudinal and lateral-directional stability data were obtained at wing yaw angles from 0 deg to 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 6 deg and 9 deg. The effects of changes in Reynolds number, dihedral, and trailing-edge angle were studied along with the effects of a roughness strip on the upper and lower surfaces of the wing. Flow-visualization studies were made to determine the nature of the flow on the wing surfaces.

Graham, L. A.↗
NASA NTRS1972

New design goals and a new shape for the SST.

Considerations are given to demonstrate that a wing which pivots as a whole would permit supersonic aircraft which avoid sonic boom and reduce noise around airports. Several such wing designs are discussed. Wind-tunnel tests results are given to support the soundness of this wing design.

Jones, R. T.↗
NASA NTRS1972

Application of multivariable search techniques to structural design optimization

Multivariable optimization techniques are applied to a particular class of minimum weight structural design problems: the design of an axially loaded, pressurized, stiffened cylinder. Minimum weight designs are obtained by a variety of search algorithms: first- and second-order, elemental perturbation, and randomized techniques. An exterior penalty function approach to constrained minimization is employed. Some comparisons are made with solutions obtained by an interior penalty function procedure. In general, it would appear that an interior penalty function approach may not be as well suited to the class of design problems considered as the exterior penalty function approach. It is also shown that a combination of search algorithms will tend to arrive at an extremal design in a more reliable manner than a single algorithm. The effect of incorporating realistic geometrical constraints on stiffener cross-sections is investigated. A limited comparison is made between minimum weight cylinders designed on the basis of a linear stability analysis and cylinders designed on the basis of empirical buckling data. Finally, a technique for locating more than one extremal is demonstrated.

Jones, R. T.↗
NASA NTRS1972

Reduction of wave drag by antisymmetric arrangement of wings and bodies.

The wave interference effects for bodies or wings in a mirror-symmetric arrangement, and in an antisymmetric arrangement are discussed. It is shown that while in the case of a mirror-symmetric arrangement large adverse interference effects can be observed, antisymmetric arrangements provide comparatively much smaller wave drags. The single continuous wing panels also adapt themselves more readily to varying angles of obliquity, and hence, to varying flight speeds. A detailed review is presented of the previous work on the aerodynamic properties and flight stability of oblique elliptic wing combinations. A possible mode of application of these combinations to transport aircraft operating at moderate supersonic speeds is suggested.

Jones, R. T.↗