Engineering Papers⌕ Search

Engineering topics

Jones, R. T.

Publications and source records attributed to Jones, R. T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Improving the efficiency of smaller transport aircraft

Considered apart from its propulsive system the high altitude airplane itself adapted to higher flight altitudes than those in current use. Scaling on the assumption of constant aircraft density indicates that this conclusion applies most importantly to smaller transport aircraft. Climb to 60,000 ft could save time and energy for trips as short as 500 miles. A discussion of the effect of winglets on aircraft efficiency is presented. A 10% reduction of induced drag below that of a comparable elliptic wing can be achieved either by horizontal or vertical wing tip extensions.

Jones, R. T.↗
NASA NTRS1984

Improving the efficiency of smaller transport aircraft

The efficiency of small transport aircraft can be improved through the adaptation of high altitude turbine engines, and that flights reaching altitudes of 40,000, 60,000, and 80,000 feet can show savings in both flight time and fuel consumption even for trips as short as 500 miles. Studies for a 40-passenger high altitude transport are presented. An increase in structural weight due to larger wing areas, larger engines, and larger engine frontal areas would make the ratio of gross weight to payload look less favorable, but the efficiency of the plane in passenger miles per gallon would increase with altitude. It is also suggested that supercritical airfoils be designed to achieve higher lift coefficients and speeds. A reduction of reduced drag through the use of horizontal or vertical wing tip extensions is also discussed.

Jones, R. T.↗
NASA NTRS1982

Relativistic kinematics for motion faster than light

The use of conformal coordinates in relativistic kinematics is illustrated and a simple extension of the theory of motions faster than light is provided. An object traveling at a speed greater than light discloses its presence by appearing suddenly at a point, splitting into two apparent objects which then recede from each other at sublight velocities. According to the present theory motion at speeds faster than light would not benefit a space traveler, since the twin paradox becomes inverted at such speeds. In Einstein's theory travel at the velocity of light in an intertial system is equivalent to infinite velocity for the traveler. In the present theory the converse is also true; travel at infinite velocity is equivalent to the velocity of light for the traveler.

Jones, R. T.↗
NASA NTRS1982

The outlook for advanced transport aircraft

The technological advances most likely to contribute to advanced aircraft designs and the efficiency, performance, and financial considerations driving the development directions for new aircraft are reviewed. Fuel-efficiency is perceived as the most critical factor for any new aircraft or component design, with most gains expected to come in areas of propulsion, aerodynamics, configurations, structural designs and materials, active controls, digital avionics, laminar flow control, and air-traffic control improvements. Any component area offers an efficiency improvement of 3-12%, with a maximum of 50% possible with a 4000 m range aircraft. Advanced turboprops have potential applications in short and medium haul subsonic aircraft, while a fuel efficient SST may be possible by the year 2000. Further discussion is devoted to the pivoted oblique wing aircraft, lightweight structures, and the necessity for short payback times.

Leavens, J. M., Jr.↗
NASA NTRS1980

Wing flapping with minimum energy

A technique employed by Prandtl and Munk is adapted for the case of a wing in flapping motion to determine its lift distribution. The problem may be reduced to one of minimizing induced drag for a specified and periodically varying bending moment at the wing root. It is concluded that two wings in close tandem arrangement, moving in opposite phase, would eliminate the induced aerodynamic losses calculated

Jones, R. T.↗
NASA NTRS1980

Wing flapping with minimum energy

For slow flapping motions it is found that the minimum energy loss occurs when the vortex wake moves as a rigid surface that rotates about the wing root - a condition analogous to that determined for a slow-turning propeller. The optimum circulation distribution determined by this condition differs from the elliptic distribution, showing a greater concentration of lift toward the tips. It appears that very high propulsive efficiencies are obtained by flapping.

Jones, R. T.↗
NASA NTRS1980

Some observations on supersonic wing design

The paper presents a brief review on the development of supersonic wing design. Attention is given to linearized aerodynamic theory, emphasizing equations for drag and ratios of slopes and Mach lines. Diagrams that depict conditions for minimum drag as well as the effects of fore-and-aft dimension of wings and Mach numbers on areas of lateral entrainment are presented.

Jones, R. T.↗
NASA NTRS1979

Classical Aerodynamic Theory

A collection of papers on modern theoretical aerodynamics is presented. Included are theories of incompressible potential flow and research on the aerodynamic forces on wing and wing sections of aircraft and on airship hulls.

Jones, R. T.↗
NASA NTRS1978

ODIN system technology module library, 1972 - 1973

ODIN/RLV is a digital computing system for the synthesis and optimization of reusable launch vehicle preliminary designs. The system consists of a library of technology modules in the form of independent computer programs and an executive program, ODINEX, which operates on the technology modules. The technology module library contains programs for estimating all major military flight vehicle system characteristics, for example, geometry, aerodynamics, economics, propulsion, inertia and volumetric properties, trajectories and missions, steady state aeroelasticity and flutter, and stability and control. A general system optimization module, a computer graphics module, and a program precompiler are available as user aids in the ODIN/RLV program technology module library.

Hague, D. S.↗
NASA NTRS1977

Dynamics of ultralight aircraft: Dive recovery of hang gliders

Longitudinal control of a hang glider by weight shift is not always adequate for recovery from a vertical dive. According to Lanchester's phugoid theory, recovery from rest to horizontal flight ought to be possible within a distance equal to three times the height of fall needed to acquire level flight velocity. A hang glider, having a wing loading of 5 kg sq m and capable of developing a lift coefficient of 1.0, should recover to horizontal flight within a vertical distance of about 12 m. The minimum recovery distance can be closely approached if the glider is equipped with a small all-moveable tail surface having sufficient upward deflection.

Jones, R. T.↗
NASA NTRS1977

Dynamics of ultralight aircraft: Motion in vertical gusts

Gust load calculations are extended to the range of conditions encountered by ultralight aircraft such as hang gliders. Having wing loadings of the order of 5 kg/sq m, these gliders acquire a substantial fraction of the motion of a gust within a distance of 1 or 2 m. Comparative loads and displacements for a small powered airplane having a wing loading of 50 kg sq m and for a commercial jet with 500 kg sq m are shown.

Jones, R. T.↗
NASA NTRS1977

The oblique wing - Aircraft design for transonic and low supersonic speeds

In tests at transonic speeds a conventional 'subsonic' wing turned at an oblique angle to the flow has demonstrated lift-drag ratios higher than conventional swept-back or delta wings. When returned to its straight position, perpendicular to the flow, such a wing would minimize the display of energy and noise in the airport environment. Following a brief review of theoretical and experimental results, the paper discusses various characteristics of the oblique wing as they relate to aircraft design. Topics covered are lift-drag ratio, flight control and trim and aeroelastic stability. The possibility of an all-wing aircraft for flight at Mach 2 is suggested.

Jones, R. T.↗
NASA NTRS1977

Recollections from an earlier period in American aeronautics

The situation of American aeronautics in the year 1929 is examined. In that year manufacturers all over the U.S. were bringing out new aircraft models to capture an assured market. Earlier developments in aviation in the U.S. after World War I are also considered along with the conditions of American aeronautics in the 1930s. Attention is given to the introduction of the Barling NB-3 with its all-metal construction, efforts of NACA to collect and disseminate in a uniform notation aerodynamic characteristics of airfoils from laboratories around the world, and the invention of the variable-density wind tunnel.

Jones, R. T.↗
NASA NTRS1976

Aeroelastic stability and control of an oblique wing - Wind tunnel experiments

Results are presented for wind tunnel tests of an elastic wing model to verify the theoretical predictions for the aeroelastic instability of an oblique wing. The model wing has an elliptic planform of 10 to 1 axis ratio and a symmetrical airfoil section of 7-1/2% thickness/chord ratio. The wing is of wood and as may be seen in the photographs presented, slack wires are used to limit the amplitude of unstable motions. The fuselage is mounted on bearings permitting freedom of roll, but provision is made to clamp the fuselage for some of the tests. It is found that freedom in roll increases the dynamic pressure at which aeroelastic instability first appears. With the model free in roll, the effectiveness of the ailerons in maintaining trim is not noticeably affected by passage through the speed at which the wing would become unstable if clamped.

Jones, R. T.↗
NASA NTRS1976

Aeroelastic stability and control of an oblique wing

Dynamic model tests were staged to compare the aeroelastic stability of a free-flying oblique-winged aircraft and the known divergent instability characterizing swept-forward wing configurations, to test the effect of wing elasticity on aileron control and trim. The aircraft fuselage was clamped in some tests and left free to roll in others. Two rigid wing panels were hinged near the wing center with elastic restraining springs. It is found that the aeroelastic divergence affecting swept-forward wings does not occur with an oblique wing, whose aeroelastic instability sets in at a dynamic pressure exceeding that for static divergence of swept-forward wings, and appears in the form of undamped oscillations. Oblique wing stability is sensitive to the moment of inertia of the fuselage in roll. Roll control and lateral trim are attainable with conventional ailerons, even at speeds at which divergence of a clamped forward wing shows up.

Jones, R. T.↗
NASA NTRS1976

Oblique-wing supersonic aircraft

An aircraft including a single fuselage having a main wing and a horizontal stabilizer airfoil pivotally attached at their centers to the fuselage is described. The pivotal attachments allow the airfoils to be yawed relative to the fuselage for high speed flight, and to be positioned at right angles with respect to the fuselage during takeoff, landing, and low speed flight. The main wing and the horizontal stabilizer are upwardly curved from their center pivotal connections towards their ends to form curvilinear dihedrals.

Jones, R. T.↗
NASA NTRS1976

Transonic lateral and longitudinal control characteristics of an F-8 airplane model equipped with an oblique wing

The aerodynamic stability and control characteristics of a 0.087-scale model of an F-8 airplane fitted with an oblique wing was studied. The wing had an elliptical planform (axis ratio = 8:1), a maximum thickness of 12 percent, and was tested at three sweep angles, 0, 45, and 60 deg. Six-component force and moment data were measured at zero sideslip for angles of attack between -6 and +16 deg, with the left and right ailerons deflected one at a time at angles between -14 deg and +14. Further tests were made with the horizontal tail deflected -5 and +2.5 deg. Test Mach numbers ranged from 0.6 to 1.4 at a Reynolds number of 20 million/m.

Smith, R. C.↗