Engineering Papers⌕ Search

Engineering topics

Jones, R. E.

Publications and source records attributed to Jones, R. E..

50 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Parametric test results of a swirl-can combustor

Pollutant levels of oxides of nitrogen, unburned hydrocarbons, and carbon monoxide were measured for three models of an experimental, annular swirl can combustor. The combustor was 1.067 meters in outer diameter, incorporated 120 modules, and was specifically designed for elevated exit temperature performance. Test conditions included combustor inlet temperatures of 589, 756 and 839 K, inlet pressures of 3 to 6.4 atmospheres, reference velocities of 21 to 38 meters per second and combustor equivalence ratios, based on total combustor flows of 0.206 to 1.028. Maximum oxides of nitrogen emission index values occurred at an equivalence ratio of 0.7 with lower values measured for both higher and lower equivalence ratios. Oxides of nitrogen concentrations, to the 0.7 level with 756 K inlet air, were correlated for the three models by a combined parameter consisting of measured flow and geometric parameters. Effects of the individual parameters comprising the correlation are also presented.

Niedzwiecki, R. W.↗
NASA NTRS1973

Advanced technology for reducing aircraft engine pollution

Combustor research programs are described whose purpose is to demonstrate significantly lower exhaust emission levels. The proposed EPA regulations covering the allowable levels of emissions will require a major technological effort if these levels are to be met by 1979. Pollution reduction technology is being pursued by NASA through a combination of in-house research, contracted progams, and university grants. In-house research with the swirl-can modular combustor and the double-annular combustor has demonstrated significant reduction in the level of NO(x) emissions. The work is continuing in an attempt to further reduce these levels by improvements in module design and in air-fuel scheduling. Research on the reduction of idle emissions has included the conversion of conventional duplex fuel nozzles to air-assisted nozzles and exploration of the potential improvements possible with fuel staging and variable combustor geometry.

Jones, R. E.↗
NASA NTRS1972

Pollution measurements of a swirl-can combustor.

Pollutant levels of oxides of nitrogen, unburned hydrocarbons, and carbon monoxide were measured for an experimental, annular, swirl-can combustor. The combustor was 42 inches in diameter, incorporated 120 modules, and was specifically designed for elevated exit temperature performance. Test conditions included combustor inlet temperatures of 600, 900 and 1050 F, inlet pressures of 5 to 6 atmospheres, reference velocities of 69 to 120 feet per second, and fuel-air ratios of 0.014 to 0.0695. Tests were also conducted at a simulated engine idle condition. Results demonstrated that swirl-can combustors produce oxides of nitrogen levels substantially lower than conventional combustor designs.

Niedzwiecki, R. W.↗
NASA NTRS1972

Pollution measurements of a swirl-can combustor

Pollutant levels of oxides of nitrogen, unburned hydrocarbons, and carbon monoxide were measured for an experimental, annular, swirl can combustor. The combustor was 42 inches in diameter, incorporated 120 modules, and was specifically designed for elevated exit temperature performance. Test conditions included combustor inlet temperatures of 600, 900 and 1050 F, inlet pressures of 5 to 6 atmospheres, reference velocities of 69 to 120 feet per second and fuel-air ratios of 0.014 to 0.0695. Tests were also conducted at a simulated engine idle condition. Results demonstrated that swirl can combustors produce oxides of nitrogen levels substantially lower than conventional combustor designs. These reductions are attributed to reduced dwell times resulting from short combustor length, quick mixing of combustion gases with diluent air, and to uniform fuel distributions resulting from the swirl can approach. Radial staging of fuel at idle conditions resulted in increases in combustion efficiencies and corresponding reductions in pollutant levels.

Niedzwiecki, R. W.↗
NASA NTRS1971

Combustion

Effects of engine design and propulsion system configurations on combustion efficiency

Grobman, J.↗
NASA NTRS1958

A Preliminary Investigation of the Performance of a Short-length Turbojet Combustor Using Vaporized Hydrocarbon Fuels

Two short turbojet combustors designed for use with vaporized hydrocarbon fuels were tested in a one-quarter annular duct. The experimental combustors consisted of many small "swirl-can" combustor elements manifolded together. This design approach allowed the secondary mixing zone to be considerably reduced over that of conventional combustors. The over-all combustion lengths, for the two configurations were 13.5 and 11.0 inches, approximately one-half the length of the shortest conventional combustors. These short combustors did not provide combustion efficiencies as high as those for conventional combustors at low pressures. However, over the range of combustor-inlet total-pressures expected in aircraft capable of flight at Mach numbers of 2.5 and above, these short combustors gave very high efficiencies. A combustion efficiency of 97 percent was obtained at a combustor-inlet total-pressure of 25.0 inches of mercury absolute, reference velocity of 120 feet per second, and inlet-air total temperature of 1160 deg R. By proportioning the fuel flow between the manifold rows of can combustor elements, control of the combustor-outlet radial total-temperature profile was demonstrated. Combustor totalpressure loss varied from 0.75 percent of the inlet total pressure at isothermal conditions and a reference velocity of 75 feet per second to 5.5 percent at a total-temperature ratio of 1.8 and a reference velocity of 180 feet per second.

Jones, R. E.↗