Engineering topics
Publications and source records attributed to Jones, J. A..
Planetary aerobots are described. They are a new type of lightweight and low-cost telerobot that use phase change fluids to ascend and descend, thus allowing data acquisition from multiple sites. Potential near-term missions discussed include those to Venus, Mars, and Titan. Similarities are discussed for missions in the Earth atmosphere and deep sea.
Simulations of observations from potential spaceborne radars are made based on storm structure generated from the three-dimensional (3D) Goddard cumulus ensemble model simulation of an intense overland convective system. Five frequencies of 3, 10, 14, 35, and 95 GHz are discussed, but the Tropical Rainfall Measuring Mission precipitation radar sensor frequency (14 GHz) is the focus of this study. Radar reflectives and their attenuation in various atmospheric conditions are studied in this simulation. With the attenuation from cloud and precipitation in the estimation of reflectivity factor (dBZ), the reflectivities in the lower atmosphere in the convective cores are significantly reduced. With spatial resolution of 4 km X 4 km, attenuation at 14 GHz may cause as large as a 20-dBZ difference between the simulated measurements of the peak, Z(sub mp) and near-surface reflectivity, Z(sub ms) in the most intense convective region. The Z(sub mp) occurs at various altitudes depending on the hydrometeor concentrations and their vertical distribution. Despite the significant attenuation in the intense cores, the presence of the rain maximum is easily detected by using information of Z(sub mp). In the stratiform region, the attenuation is quite limited (usually less than 5 dBZ), and the reduction of reflectivity is mostly related to the actual vertical structure of cloud distribution. Since Z(sub ms) suffers severe attenuation and tends to underestimate surface rainfall intensity in convective regions. Z(sub mp) can be more representative for rainfall retrieval in the lower atmosphere in these regions. In the stratiform region where attenuation is negligible, however, Z(sub mp) tends to overestimate surface rainfall and Z(sub ms) is more appropriate for rainfall retrieval. A hybrid technique using a weight between the two rain intensities is tested and found potentially usefull for future applications. The estimated surface rain-rate map based on this hybrid approach captures many of the details of the cloud model rain field but still slightly underestimates the rain-rate maximum.
In simple sorption refrigeration system, low pressure gases are physically adsorbed onto or chemically absorbed into various solids, typically near ambient temperatures or above.
Estimates of rain rate derived from a spaceborne weather radar will be most reliable over an intermediate range of values. In forming an area average of the rain rate, an alternative to the averaging of the high-resolution estimates, irrespective of their individual accuracies, is a multiple threshold approach. The method is based on the fact that the fractional area above a particular rain-rate threshold R(j) is related to the cumulative distribution of rain rates evaluated at R(j). Varying the threshold over the effective dynamic range of the radar yields the cumulative distribution function over this range. To obtain the distribution at all rain rates, a lognormal or gamma test function is selected such that the mean-square error between the test function and the measured values is minimized. Once the unknown parameters are determined, the first-order statistics of the areawide rain-rate distribution can be found. Tests of the method with data from the SPANDAR radar provide comparisons between it and the single threshold and the direct averaging approaches.
A 3D cloud model is used to simulate the storm structure, and the results are linked to microwave and infrared radiative transfer models for simulation of aircraft observations. Spaceborne radar data are also simulated along the aircraft flight track. The cloud and radiative model simulations are studied and compared with aircraft observations. The initial results indicate that the 3D cloud model is capable of simulating the major features of observed storm systems when given a representative atmospheric sounding to initialize the convective systems. The simulations of infrared and microwave radiances provide reasonably good comparisons with the observations.
Interplanetary magnetic clouds emerge as a feature of the solar wind at 1 AU, exhibiting enhanced field strength and lower plasma temperature and density than the surrounding plasma. A least-squares program has been developed which fits magnetic field data within a cloud, while estimating such cloud properties as its size, maximum field strength, and axis inclination. The results obtained from a study of 12 clouds observed at 1 AU point to a probable cloud axis direction within 15 deg of the ecliptic plane and about 100 deg from the sun's direction, when projected into the ecliptic plane. A wide variety of orientations is observed; some extend to 80 deg from the ecliptic.
Simple heating and cooling of chemisorption and physisorption compressors provide high pressure gas, which, when expanded through a Joule-Thomson (J- T) valve, can provide cooling from 0.3 to 200 K depending on the sorbent/gas combination. System life tests are under way on Pr(1-n)Ce(n)O(x)/O2 (PCO/O2) chemisorption compressors for 65-80 K cooling and on carbon/krypton (C/Kr) physisorption compressors for 120-140 K cooling. Investigations have been initiated to examine reliability physics issues related to critical compressor components such as sorbents, container materials and electrical heaters.
A magnetic cloud associated with a 2N flare on January 1, 1978 was observed by IMP-8, Helios A, Helios B, and Voyager 2. The variation of the magnetic field observed at each spacecraft is represented to good approximation by Lundquist's solution for a cylindrically symmetric force-free magnetic field with constant alpha. A least-squares fit of Lundquist's solution to the data from each spacecraft gives the local orientation of the axis of the magnetic cloud. The times of the estimated boundaries of the magnetic cloud at each spacecraft, together with the speeds of the boundaries and the spacecraft position, give the positions of the boundaries at a given time. From these results the magnetic cloud is determined to resemble a flux rope whose minor radius is approximately 0.15 AU at 1 AU, and whose radius of curvature at 1 AU is approximately 1/3 AU.
The Wide Field/Planetary Camera is an imaging system developed by the Jet Propulsion Laboratory for the NASA Hubble Space Telescope currently scheduled to be launched in December 1989 aboard the space shuttle. The temperature control design of the instrument utilizes multilayered insulation, electric resistance heaters, aluminum/ammonia heat pipes, thermoelectric coolers, temperature control coatings, and space radiators. A feedback control system maintains stable sensor temperatures. Thermal capacitance maintains stable optics and electronics temperatures during transient conditions. Schedule slips and launch delays have allowed extensive thermal testing of the instrument. Six instrument thermal vacuum tests and a spacecraft thermal vacuum test were performed. Several modifications have been made to the instrument to correct icing and contamination problems that have been discovered during thermal vacuum testing. This paper describes the thermal design, last instrument thermal vacuum test, results, and thermal model correlation.
Experience with Deep Space Network (DSN) ground-based cryogenic refrigerators has proved the reliability of the basic two-stage Gifford-McMahon helium refrigerator. A very long life cryogenic refrigeration system appears possible by combining this expansion system or a turbo expansion system with a hydride sorption compressor in place of the usual motor driven piston compressor. To test the feasibility of this system, a commercial Gifford-McMahon refrigerator was tested using hydrogen gas as the working fluid. Although no attempt was made to optimize the system for hydrogen operation, the refrigerator developed 1.3 W at 30 K and 6.6 W at 60 K. The results of the test and of theoretical performances of the hybrid compressor coupled to these expansion systems are presented.
This paper presents the design and test performance of a conical cavity type blackbody radiance source that will meet the requirements of the Halogen Occultation Experiment on the NASA Upper Atmospheric Research Satellite program. The thrust of this design effort was to minimize the heat losses, in order to keep the power usage under 7.5 watts, and to minimize the amount of silica in the materials. Silica in the presence of the platinum heater winding used in this design would cause the platinum to erode, changing the operating temperature set-point. The design required the development of fabrication techniques which would provide very small, close tolerance parts from extremely difficult-to-machine materials. Also, a space rated ceramic core and unique, low thermal conductance, ceramic-to-metal joint was developed, tested and incorporated in this design. The completed flight qualification hardware has undergone performance, environmental and life testing. The design configuration and test results are discussed in detail.
New seal more effective and lasts longer. Seal consists of five felt rings interspersed with four polytetrafluoroethylene rings having inner diameter slightly larger than shaft. Spaces between polytetrafluoroethylene rings and shaft produce labyrinth effect, which increases degree of sealing.
Improved design reduces clogging and maintains constant pressure drop as flow rate varies. Spring-Loaded Joule-Thomson Valve pressure drop regulated by spring pushing stainless-steel ball against soft brass seat. Pressure drop remains nearly constant, regardless of helium flow rate and of any gas contaminants frozen on valve seat. Because springloaded J-T valve maintains constant pressure drop, upstream roomtemperature throttle valve adjusts flow rate precisely for any given upstream pressure. In addition, new valve relatively invulnerable to frozen gas contaminants, which clog fixed-orifice J-T valves.
Closed-cycle hydrogen refrigerator uses low-level heat energy to cool objects to temperature of 10 K. Refrigerator needs only fraction of energy of previous equipment with similar low-temperature capability. Unit compact and light in weight. With valves as only moving parts, reliable for many years. Refrigeration concept adapted to cooling superconducting magnets on magnetically levitated railcars, nuclear-particle accelerators, and variety of other cryogenic equipment.
Hydrogen-absorption refrigerating system provides about 650 mW of cooling at 20 to 29 K in continuous, closed-cycle operation. Three thermally cycled absorbers/desorbers act as compressors. System successfully tested below 29 K for over 1,000 h, while separate room-temperature hydride compressor operated continuously for 6,000 h. Due to lack of moving parts, lifetimes of 10 years or more eventually expected.
A very long-life, lightweight and efficient hydride absorption refrigerator system was built to operate at ten Kelvin and below. The system consists of four basic stages of refrigeration. The first stage is accomplished by an active refrigeration system. The second stage is operated by a hydride absorption system, wherein a heated hydride powder drives off high pressure hydrogen through a Joule-Thomson/heat exchanger expansion loop such that the hydrogen is partially liquefied. In the third stage, the vapor pressure over the collected liquid hydrogen is lowered by absorbing the hydrogen vapor onto a different low pressure, worn hydride. With a 1.7 torr partial pressure of hydrogen gas in the hydride, liquid hydrogen is solidified and sublimes at 10 K. Long-life adiabatic demagnetization refrigerators, helium desorption, or helium diaphragm compressors are used to cool to 4 K or below. It is shown that the hydride concepts provide an extremely efficient means of refrigeration to 10 K, and that an entire sorption refrigeration process can be accomplished solely by using low grade heat energy at about 150 C.
Temperature sensing system detects presence of gas slugs in heat pipes. System designed for operation between zero and 70 degrees C and detects noncondensable pockets of gas that result from decomposition of ammonia cooling fluid. Slugs 1 in. (25mm) in length detected.
Internal gas slugs reduced or eliminated. Manufacturing method increases efficiency of aluminum heat pipes in which ammonia is working fluid by insuring pipe filled with nearly pure charge of ammonia. In new process heat pipe initially closed with stainless-steel valve instead of weld so pipe put through several cycles of filling, purging, and accelerated aging.