Engineering Papers⌕ Search

Engineering topics

Jones, D. L.

Publications and source records attributed to Jones, D. L..

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Fatigue of graphite/epoxy /0/90/45/-45/s laminates under dual stress levels

A model for the prediction of loading sequence effects on the statistical distribution of fatigue life and residual strength in composite materials is generalized and applied to (0/90/45/-45)s graphite/epoxy laminates. Load sequence effects are found to be caused by both the difference in residual strength when failure occurs (boundary effect) and the effect of previously applied loads (memory effect). The model allows the isolation of these two effects, and the estimation of memory effect magnitudes under dual fatigue loading levels. It is shown that the material memory effect is insignificant, and that correlations between predictions of the number of early failures agree with the verification tests, as do predictions of fatigue life and residual strength degradation under dual stress levels.

Yang, J. N.↗
NASA NTRS1981

Biaxial tests of flat graphite/epoxy laminates

The influence of biaxially applied loads on the strength of composite materials containing holes was analyzed. The analysis was performed through the development of a three dimensional, finite element computer program that is capable of evaluating fiber breakage, delamination, and matrix failure. Realistic failure criteria were established for each of the failure modes, and the influence of biaxial loading on damage accumulation under monotonically increasing loading was examined in detail. Both static and fatigue testing of specially designed biaxial specimens containing central holes were performed. Static tests were performed to obtain an understanding of the influence of biaxial loads on the fracture strength of composite materials and to provide correlation with the analytical predictions. The predicted distributions and types of damage are in reasonable agreement with the experimental results. A number of fatigue tests were performed to determine the influence of cyclic biaxial loads on the fatigue life and residual strength of several composite laminates.

Liebowitz, H.↗
NASA NTRS1981

Development of a surface panel measurement system

Reflector measurement systems are studied in support of the reshaping of the 34 meter antenna at Goldstone. The requirements for measurement systems are presented. A survey is made of the surface errors of existing antennas. Reflector measurement systems are divided into three categories and representative examples of each category are illustrated and discussed. Parametric error analyses are made of selected optical systems. The existing measurement method using a theodolite at the vertex is retained. A method using a theodolite on the RF cone is a possible variant.

Jones, D. L.↗
NASA NTRS1981

Determination of load sequence effects on the degradation and failure of composite materials

A theoretical model was established to predict the fatigue behavior of composite materials, with emphasis placed on predictions of the degradation of residual strength and residual stiffness during fatigue cycling. The model parameters were evaluated from three test series including static strength fatigue life and residual strength tests. The tests were applied to two graphite/epoxy laminates. Load sequence effects were emphasized for both laminates and the predicted results agreed quite well with subsequent verification tests. Dynamic as well as static stiffness reduction data were collected by use of a PDP11-03 computer, which performed quite satisfactorily and permitted the recording of a substantial amount of dynamic stiffness reduction data.

Yang, J. N.↗
NASA NTRS1981

Load sequence effects on the fatigue of unnotched composite materials

A more comprehensive version of an earlier fatigue and residual strength degradation model is proposed to predict the effect of load sequence on the statistical fatigue behavior of composite laminates. The model, which reduces to various fatigue models proposed in the literature by means of approximations, is verified by a survey of experiments on glass/epoxy laminates. It is shown that the correlation between the model and the test results under dual stress levels is reasonable, and that a simplified version of the model is verified by experiments on graphite/epoxy laminates in which the correlation between theoretical predictions and results under dual stress levels is satisfactory. The model is also shown capable of predicting the effect of proof loads on the fatigue behavior of composite materials.

Yang, J. N.↗
NASA NTRS1980

Statistical fatigue of unnotched composite laminates

A general analytical, phenomenological model is developed for characterizing fatigue damage accumulation in unnotched composite laminates, and experimental results are used to evaluate the model. The fatigue model, which is developed for various types of cyclic loadings, is based on the assumption that the residual strength reduction is a monotonically decreasing function of the fatigue life. Parameters are determined from baseline test data consisting of one set of residual strength data, one set of static strength data, and one set of constant amplitude fatigue life data. Once the parameters are determined, the model is able to predict: (1) the statistical distribution of the fatigue life, and the residual strength under constant and variable amplitude loads, and (2) the effect of periodic proof tests, without any additional experimental data. Experimental test results show that predictions made from the present model agree quite well with the experimental results. The model is also applicable to fatigue of bonded or bolted composite joints.

Yang, J. N.↗
NASA NTRS1979

Statistical characterization of the fatigue behavior of composite lamina

A theoretical model was developed to predict statistically the effects of constant and variable amplitude fatigue loadings on the residual strength and fatigue life of composite lamina. The parameters in the model were established from the results of a series of static tensile tests and a fatigue scan and a number of verification tests were performed. Abstracts for two other papers on the effect of load sequence on the statistical fatigue of composites are also presented.

Yang, J. N.↗
NASA NTRS1979

The effect of load sequence on the statistical fatigue of composites

A theoretical model to predict the effect of loading sequence on the statistical distributions of the fatigue life and the residual strength under n-stress levels of cyclic loading is derived on the basis of a three-parameter model. In particular, the dual stress fatigue cumulative damage is studied, showing that the Miner's sum (the cumulative damage sum at fatigue failure) is a statistical variable. It is proved theoretically that the Miner's sum is always greater than or equal to unity for the high-low load sequence, while it is always smaller than or equal to unity for the low-high load sequence, with the deviation from unity increasing as the difference between the high and the low stress levels increases. An experimental test program using graphite/epoxy angle-ply laminates, carried out to generate statistically meaningful data for verifying the proposed model, is discussed.

Yang, J. N.↗
NASA NTRS1978

Statistical fatigue of graphite/epoxy angle-ply laminates in shear

A three-parameter fatigue and residual strength degradation model has been proposed to predict statistically the fatigue behavior of composite laminae under axial shear loadings. The fatigue behavior includes the fatigue life and the fatigue damage expressed in terms of the residual strength degradation. An experimental test program using graphite/epoxy /+ or - 45 deg/2s laminates has been conducted to generate statistically meaningful data in order to examine the validity of the theoretical model. It is shown that the correlation between the theoretical predictions and the test results on the statistical distributions of the fatigue life and the residual strength is excellent. Test results on the shear modulus degradation are also presented and discussed in detail in order to provide insight for the establishment of a shear modulus degradation model.

Yang, J. N.↗
NASA NTRS1976

Determination of nonlinear energy toughness values for cyclic loading applications

For several years the nonlinear energy method proposed by Liebowitz and Eftis has been examined as a failure criterion for static testing of center-cracked and compact tension specimens. Since the method appears to be valid under conditions of crack-tip plasticity, subcritical crack growth and load relaxation, tests have been conducted to ascertain the merit of this method as a failure criterion under cyclic loading conditions. The nonlinear energy toughness for cyclic loading is obtained from an envelope of the cyclic load-displacement record, which naturally imposes some restrictions on the loading program. The cyclic toughness parameter has been evaluated for thin center-cracked sheets of 2024-T3 and 7075-T6 aluminum alloys. Both alloys exhibited a significant reduction of the cyclic toughness parameter with increasing cyclic life in a manner similar to the classical S-N diagram. It is suggested that this method may serve the design process by allowing the establishment of a fracture toughness parameter capable of including the effects of the entire loading history of a structure into the fracture toughness requirements.

Poulose, P. K.↗
NASA NTRS1976

A study of the effect of subcritical crack growth on the geometry dependence on nonlinear fracture toughness parameters

The effect of subcritical crack growth on the geometry dependence of nonlinear fracture toughness parameters was studied by comparing the toughness values for different specimen geometries at the onset of subcritical crack growth and at the initiation of unstable crack propagation. Center-cracked thin sheet specimens of 2024-T3 and 7075-T6 aluminum alloys were tested by varying the specimen length L, width w, and crack length-to-width ratio c/w. When the onset of unstable crack propagation was selected as the critical point, the nonlinear energy toughness and the R curve toughness increased with increasing w and decreasing L and c/w. However, when the onset of subcritical crack growth was taken as the critical point, energy toughness and the linear toughness values were independent of these geometrical variables.

Jones, D. L.↗
NASA NTRS1976

A fractographic study of the edge-sliding mode in fracture toughness testing

A fractographic study of Mode II fracture surfaces has been conducted for the purpose of identifying the microstructural mechanisms responsible for fracture in the edge-sliding mode. A compact shear (CS) specimen was employed to generate the fracture surfaces and also to establish Mode II fracture toughness values for Ti-6Al-4V, A533-B steel, and several aluminum alloys. In all tests, one of the two edge cracks sustained complete Mode II fracture while the other exhibited only a limited amount of subcritical crack growth. Mode II fracture surfaces, which were unique in appearance, have been examined by optical and scanning electron microscopy. It was determined that shear (or parabolic) microvoid coalescence was the dominant mechanism for Mode II fracture. It was also established that most of the surface abrasions were created by the relative sliding of the fracture surfaces during unstable fracture rather than the crack initiation process.

Jones, D. L.↗
NASA NTRS1975

On fracture toughness in the nonlinear range

A general definition of fracture toughness is developed which is appropriate to situations of subcritical crack growth and/or large-scale crack border plastic yield. The theoretical basis as well as comparisons with other proposed measures of fracture toughness are discussed. A simple method is given for evaluating fracture toughness which is based on use of the load-displacement test record.

Eftis, J.↗
NASA NTRS1975

An investigation of the edge-sliding mode in fracture mechanics

A boundary collocation procedure has been applied to the Williams stress function to determine the elastic stress distribution for the crack tip region of a finite, edge-cracked plate subjected to mode II loading at the crack tips. The asymmetric specimen selected was particularly suitable for the determination of plane strain fracture toughness for mode II loading. Numerical solutions for stress intensity factors for the edge-sliding mode obtained by the boundary collocation method were in close agreement with values obtained from photoelastic experiments. Fracture tests of several compact shear specimens of 2024-T4 aluminum were conducted in order to experimentally investigate the behavior of the edge-sliding mode. In each case a brittle shear failure was observed and mode II fracture toughness values were obtained. The average value for K-IIc obtained from two tests was 39.5 ksi radical (in). No K-Ic data for 2024-T4 were available for comparison purposes; however, K-Ic values for a similar alloy, 2024-T351, have been reported as 34 ksi radical (in) which is only about 15 per cent below the corresponding K-IIc value.

Jones, D. L.↗
NASA NTRS1975

An analytical and experimental stress analysis of a practical mode II fracture-test specimen

A boundary collocation method has been employed to determine the Mode II stress intensity factors for a pair of through-the-thickness edge cracks in a finite isotropic plate. An elastostatic analysis has been carried out in terms of the complete Williams stress function employing both even and odd components. The results of the numerical analysis were verified by a two-step procedure whereby the symmetric and antisymmetric portions of the solution were independently compared with existing solutions. The complete solution was verified by comparison with a photoelastic analysis. A compact shear specimen (CSS) of Hysol epoxy resin was loaded in a photoelastic experiment designed to study the isochromatic fringe patterns resulting from the Mode II crack tip stress distribution. The experiment verified that a pure Mode II stress distribution existed in the neighborhood of the crack tips and confirmed the accuracy of the boundary collocation solution for the Mode II stress intensity factors.

Chisholm, D. B.↗
NASA NTRS1975

Effect of crack initiation, stable crack growth and unstable crack propagation on the crack-tip plastic zone

A technique for measuring the plastic zones associated with initial crack-tip yielding, subcritical crack growth, and unstable fracture is discussed. The results of the measurement of the locus of these yield regions, on center-cracked sheet and compact tension specimens of 7075-T6, 7075-T651, and 2024-T3 aluminum, are reported in this paper. It was found that a very accurate representation of the strains was obtained by this method and that the results added significant insight into the fracture process. The plastic zones were found to be approximately eight times wider in 2024-T3 than in the 7075-T6 sheets. The yield zones approached a maximum value after unstable fracture was attained and maintained that size through the fast fracture region. As expected, the plastic zones in the compact tension specimen were associated only with the formation of the shear lips and no plastic zones were observed in the fatigue precracked regions of either the center-cracked or compact-tension specimens.

Poulose, P. K.↗
NASA NTRS1974

Theoretical and experimental comparisons of the nonlinear energy method to the J-integral, R-curve and COD methods in fracture toughness testing

Because of the current high degree of interest in the development of a standard nonlinear test method, analytical and experimental comparisons have been made between the R-curve, COD, J-integral and nonlinear energy methods. A general definition of fracture toughness is proposed and the fundamental definitions of each method are compared to it. Experimental comparisons between the COD, J-integral, nonlinear energy and standard ASTM methods have been made for a series of compact tension tests on several aluminum alloys. Some of the tests were conducted according to the ASTM standard method E399-72, while the specimen thickness was reduced below the minimum requirement for plane strain fracture toughness testing for several other test series. The fracture toughness values obtained by the COD method were significantly higher than the toughness values obtained by the other three methods. All of the methods displayed a tendency to yield higher toughness values as the thickness was decreased below the ASTM plane strain requirement.

Liebowitz, H.↗