Jankovsky, Robert S. — Page 2 | Engineering Papers

NASA NTRS1997

HAN-Based Monopropellant Propulsion System with Applications

NASA is developing a new monopropellant propulsion system for small, cost-driven spacecraft with AV requirements in the range of 10-150 m/sec. This system is based on a hydroxylammonium nitrate (HAN)/water/fuel monopropellant blend which is extremely dense, environmentally benign, and promises good performance and simplicity. State-of-art (SOA) small spacecraft typically employ either hydrazine or high pressure stored gas. Herein, a 'typical' small satellite bus is used to illustrate how a HAN-based monopropellant propulsion system fulfills small satellite propulsion requirements by providing mass and/or volume savings of SOA hydrazine monopropellants with the cost benefits of a stored nitrogen gas.

Jankovsky, Robert S.↗

NASA NTRS1996

HAN-based monopropellant assessment for spacecraft

The growing cost of space missions, the need for increased mission performance, and concerns associated with environmental issues are changing rocket design and propellant selection criteria. Whereas a propellant's performance was once defined solely in terms of specific impulse and density, now environmental safety, operability, and cost are considered key drivers. Present emphasis on these considerations has heightened government and commercial launch sector interest in Hydroxylammonium Nitrate (HAN)-based liquid propellants as options to provide simple, safe, reliable, low cost, and high performance monopropellant systems.

Jankovsky, Robert S.↗

NASA NTRS1996

Experimental performance of a high-area-ratio rocket nozzle at high combustion chamber pressure

An experimental investigation was conducted to determine the thrust coefficient of a high-area-ratio rocket nozzle at combustion chamber pressures of 12.4 to 16.5 MPa (1800 to 2400 psia). A nozzle with a modified Rao contour and an expansion area ratio of 1025:1 was tested with hydrogen and oxygen at altitude conditions. The same nozzle, truncated to an area ratio of 440:1, was also tested. Values of thrust coefficient are presented along with characteristic exhaust velocity efficiencies, nozzle wall temperatures, and overall thruster specific impulse.

Jankovsky, Robert S.↗

NASA NTRS1995

Rocket Combustion Chambers Resist Thermal Fatigue

Improved design concept developed for combustion chambers for rocket engines, described in three reports. Provides compliance allowing unrestrained thermal expansion in circumferential direction. Compliance lengthens life of rocket engine by reducing amount of thermal deformation caused by repeated firings.

Kazaroff, John M.↗

NASA NTRS1994

Structurally compliant rocket engine combustion chamber: Experimental and analytical validation

A new, structurally compliant rocket engine combustion chamber design has been validated through analysis and experiment. Subscale, tubular channel chambers have been cyclically tested and analytically evaluated. Cyclic lives were determined to have a potential for 1000 percent increase over those of rectangular channel designs, the current state of the art. Greater structural compliance in the circumferential direction gave rise to lower thermal strains during hot firing, resulting in lower thermal strain ratcheting and longer predicted fatigue lives. Thermal, structural, and durability analyses of the combustion chamber design, involving cyclic temperatures, strains, and low-cycle fatigue lives, have corroborated the experimental observations.

Jankovsky, Robert S.↗

NASA NTRS1993

Electroform Welding

Electroform welding used to join variety of parts without addition of detrimental heat. Technique developed so large and/or complexly shaped parts joined without degrading properties of materials. Commercial uses include joining dissimilar alloys. Beneficial for suppression of distortion or maintenance of close tolerances in precise components.

Kazaroff, John M.↗

NASA NTRS1992

Hot fire test results of subscale tubular combustion chambers

Advanced, subscale, tubular combustion chambers were built and test fired with hydrogen-oxygen propellants to assess the increase in fatigue life that can be obtained with this type of construction. Two chambers were tested: one ran for 637 cycles without failing, compared to a predicted life of 200 cycles for a comparable smooth-wall milled-channel liner configuration. The other chamber failed at 256 cycles, compared to a predicted life of 118 cycles for a comparable smooth-wall milled-channel liner configuration. Posttest metallographic analysis determined that the strain-relieving design (structural compliance) of the tubular configuration was the cause of this increase in life.

Kazaroff, John M.↗

NASA NTRS1992

Hot fire fatigue testing results for the compliant combustion chamber

A hydrogen-oxygen subscale rocket combustion chamber was designed incorporating an advanced design concept to reduce strain and increase life. The design permits unrestrained thermal expansion of a circumferential direction and, thereby, provides structural compliance during the thermal cycling of hot-fire testing. The chamber was built and test fired at a chamber pressure of 4137 kN/sq m (600 psia) and a hydrogen-oxygen mixture ratio of 6.0. Compared with a conventional milled-channel configuration, the new structurally compliant chamber had a 134 or 287 percent increase in fatigue life, depending on the life predicted for the conventional configuration.

Pavli, Albert J.↗

NASA NTRS1991

A dual-cooled hydrogen-oxygen rocket engine heat transfer analysis

The potential benefits of simultaneously using hydrogen and oxygen as rocket engine coolants are described. A plug-and-spool rocket engine was examined at heat fluxes ranging from 9290 to 163,500 kW/sq m, using a combined 3D conduction/advection analysis. Both counterflow and parallel flow cooling arrangements were analyzed. The results indicate that a significant amount of heat transfer to the oxygen occurs, reducing both the hot-side wall temperature of the rocket engine and also reducing the exit temperature of the hydrogen coolant. The total heat transferred to the oxygen was found to be largely independent of the oxygen coolant flow direction. The reduction in combustion chamber wall temperatures at throttled conditions is especially desirable since the analysis indicates that double temperature maxima, one at the throat and another in the combustion chamber, occur with a traditional hydrogen-only cooled engine. A dual-cooled engine eliminates any concern for overheating in the combustion chamber.

Kacynski, Kenneth J.↗

NASA NTRS1991

A dual-cooled hydrogen-oxygen rocket engine heat transfer analysis

The potential benefits of simultaneously using hydrogen and oxygen as rocket engine coolants are described. A plug-and-spool rocket engine was examined at heat fluxes ranging from 9290 to 163,500 kW/sq m, using a combined 3-D conduction/advection analysis. Both counter flow and parallel flow cooling arrangements were analyzed. The results indicate that a significant amount of heat transfer to the oxygen occurs, reducing both the hot side wall temperature of the rocket engine and also reducing the exit temperature of the hydrogen coolant. In all heat flux and coolant flow rates examined, the total amount of heat transferred to the oxygen was found to be largely independent of the oxygen coolant flow direction. At low heat flux/low coolant flow (throttled) conditions, the oxygen coolant absorbed more than 30 percent of the overall heat transfer from the rocket engine exhaust gasses. Also, hot side wall temperatures were judged to decrease by approximately 120 K in the throat area and up to a 170 K combustion chamber wall temperature reduction is expected if dual cooling is applied. The reduction in combustion chamber wall temperatures at throttled conditions is especially desirable since tha analysis indicates that a double temperature maxima, one at the throat and another in the combustion chamber, occurs with a traditional hydrogen cooled only engine. Conversely, a dual cooled engine essentially eliminates any concern for overheating in the combustion chamber.

Kacynski, Kenneth J.↗

NASA NTRS1990

Cyclic hot firing results of tungsten-wire-reinforced, copper-lined thrust chambers

An advanced thrust liner material for potential long life reusable rocket engines is described. This liner material was produced with the intent of improving the reusable life of high pressure thrust chambers by strengthening the chamber in the hoop direction, thus avoiding the longitudinal cracking due to low cycle fatigue that is observed in conventional homogeneous copper chambers, but yet not reducing the high thermal conductivity that is essential when operating with high heat fluxes. The liner material produced was a tungsten wire reinforced copper composite. Incorporating this composite into two hydrogen-oxygen test rocket chambers was done so that its performance as a reusable liner material could be evaluated. Testing results showed that both chambers failed prematurely, but the crack sites were perpendicular to the normal direction of cracking indicating a degree of success in containing the tremendous thermal strain associated with high temperature rocket engines. The failures, in all cases, were associated with drilled instrumentation ports and no other damages or deformations were found elsewhere in the composite liners.

Kazaroff, John M.↗