Engineering topics
Publications and source records attributed to Hubbard, Lance R..
This fiscal year we investigated the kinetic mechanism of electroplating of titanium on stainless steel substrates, as well as the influence of additives on the brightness and smoothness of this plating, as related to the FY24 LD-TCF proposal.
The ability to remove heat is paramount to nuclear fuel performance and longevity. Retaining fission product and separating fuel from reactor coolant and the environment is also necessary to prevent radiological contamination. Conventional nuclear fuel for commercial light water reactors and radioisotope power systems (RPS) is composed of oxide powders pressed into a pellet (cm-scale) and then sealed into a metal cladding to confine the fuel. What typical fuels lack is a method to surround each particle of nuclear fuel in metal, thus providing a more intimate protection layer for accident tolerance and boosting the thermal extraction from the fuel element. In such a way, metal-coated fuel particles increase heat extraction efficiency over clad-pellet designs while increasing the accident tolerance of the fuel. Metal oxide microspheres have wide-ranging applications, including the realm of fuels for nuclear reactors and RPS. Microspheres of uranium oxide/uranium carbide, mixed uranium/plutonium oxides, transuranics, and thorium fuels have been extensively studied. Pacific Northwest National Laboratory has also demonstrated the production of 238 PuO 2 microspheres for RPS applications. Metal-coated oxide microsphere fuels may also be attractive for other applications such as nuclear thermal rockets, future nuclear reactor designs, and catalysts.
PNNL has successfully integrated a commercial aerosol detector and the imprinted micelle technology. The integrated systems have been shown to have a limit of detection between 33-47 particles with several options for data analysis presented that vary on computational requirements. It is possible to integrate these systems and receive response data on the second time scale. While more work is needed, these technologies are compatible, which opens up a large field of air sampling looking for specific contaminates.
A beta-voltaic device made up of silica covered scintillating particles incorporated within an isotope absorbing layer to produce an improved power source. Lost beta particles are converted to UV light which is also converted to power in a beta-voltaic converter. The addition of the scintillating particles effectively increases the power efficiency of a BV device while maintaining the slim profile and smaller size of the power source. This arrangement makes possible implementation in space, defense, intelligence, medical implants, marine biology and other applications.
Three tasks were proposed for this work. All three were completed. The tasks were as follows: Task 1: A larger plating system will be purchased for process scale-up. TiF 3 will be tested as the metal precursor in an effort to reduce water sensitivity of the process. Task 2: Ti on steel samples will be created at PNNL and shipped to Atlas Technologies. Atlas Technologies will diffusion bond the samples to aluminum and test the bond strength. The results will be reported to PNNL. Task 3: Investigation into DOE mission relevant Ti and Zr alloys and demonstration on larger scale work pieces.
Disclosed herein are embodiments of a coating composition and a method of using the same for forming metal coatings on substrates. In particular embodiments, the coating composition comprises a deep eutectic solvent and/or an ionic liquid; a metal precursor; an alkali metal salt; and an optional additive component. The coating composition and method embodiments disclosed herein provide durable, even, high-surface area coatings on various types of substrates and also can be used at low temperatures.
The near real-time detection of airborne particles-of-interest is needed for avoiding current/future threats. The incorporation of imprinted particles into a micelle-based electrochemical cell produced a signal when brought into contact with particle analytes (such as SARS-COV-2), previously imprinted onto the structure. Nanoamp scales of signals were generated from what may’ve been individual virus-micelle interactions. The system showed selectivity when tested against similar size and morphology particles. The technology was compatible with airborne aerosol sampling techniques. Overall, the application of imprinted micelle technology could provide near real-time detection methods to a host of possible analytes of interest in the field.
Experiments were conducted to investigate a passive production mechanism for the world’s most energy intensive commodity, ammonia. A novel method, gamma catalyzed ammonia production at ambient conditions, was investigated. Ammonia is currently produced through the highly energy intensive Haber-Fritz process, which requires an operation pressure of 400 atmosphere and 600 degrees Celsius. Due to the high demand and need for ammonia, the Haber-Bosch process consumes 25% all energy produced globally. Reported herein was an attempt to produce ammonia at ambient temperature (20 C) and ambient pressure (1 atm), through a novel process developed at PNNL, gamma driven catalysis of ammonia. Although the measurements of the ammonia production suggest wild success, reports in the literature by Gao et.al. suggest an experimental positive bias in the results. To rule out the potential positive bias, multiple additional production campaigns would be needed to with an alternate analysis technique such as ion chromatography, as suggested by Gao et.al. Unfortunately, due to this late determination of potential positive bias, the results of this study remain inconclusive to the feasibility of gamma driven catalysis of ammonia and more work is needed to describe the chemical evolution with time. The results are a first step and demonstrate that gamma-catalyst mediated reactions are possible. This represents a key opportunity to explore the fundamental chemistry of high band gap catalysts that can change the paradigm of radiation, transforming it from a waste to a valuable energy source.
Non-aqueous ionic mixture electroplating allows for room-temperature or near-room-temperature applications of thin metal films, typically metals for which aqueous solvents cannot be used. While there are many methods of plating zirconium, each has disadvantages that ionic liquid plating could correct. However, ionic liquid plating requires further research and development, as a new class of solvents were only developed a few years ago. Current ionic liquids cost several thousand dollars per liter, yet produce films with less than 90% surface coverage as well as deposition of salt species that enable interdiffusion through the Zr. Film coverage needs to be increased while maintaining approximate room temperatures and lower solvent costs. Current ionic liquid technology has suffered from poor surface wetting and limited Zr diffusivity leading to dendrite formation which inhibits total surface coverage. Zr electroplating can be improved by application of room-temperature ionic mixtures as the plating medium. We have successfully demonstrated the capability to plate high-quality metallic zirconium layers using deep eutectic solvents (DES) and DES-ionic liquid (IL) mixtures. Plating thicknesses of up to 6 microns have been achieved, and the coatings are conformal to the substrate and not dendritic, with low contamination from the plating solution. Our current method uses the DES ethaline (a 1:2 ratio of choline chloride and ethylene glycol) to complex zirconium (IV) ions (present via the addition of ZrF4). We pulse plate the Zr from a bath with an overabundance of LiF, in accordance with prior literature. We have also had success in mixing the DES with ILs, such as Triethylsulfonium bis(trifluoromethylsulfonyl)imide, 1-Butyl-3-methylpyridinium bis(trifluormethylsulfonyl)imide, Methyl-trioctylammonium bis(trifluoromethylsulfonyl)imide, and Diethylmethyl(2-methoxyethyl)ammonium bis(trifluoromethylsulfonyl)imide.
Currently, there is no good way to determine the influence of the radiation on the aging of betavoltaic electrical contacts. Here, this work tested a method to accelerate the aging of the contacts inside a betavoltaic by enhancing energy deposition within the interfacial region of interest. An electrical contact of gold-titanium on gallium nitride was aged by exposure to tritium betas and electrons in a beamline. The interface stoichiometry was compared to the electrical performance of the contact. The method to age the betavoltaic component could help predict lifetime performance of the internal electrical contacts and provide assurance of deployment reliability.
Titanium & Zirconium metal films have been electroplated by a near-ambient scalable process for high value-add/lower volume applications. The films have been commercially tested as bonding layers
Betavoltaics (BV) are long-life power sources that typically convert beta particle radiation into electricity. Largely, the radioactive decays within the source go unharvested by the device. This work seeks to augment the power generation of BV devices by integration of scintillating particles within the radiative getter to convert beta emission which would otherwise not leave the getter into usable light for power generation. Silica-covered barium fluoride scintillating particles were integrated into a tritiated water getter. Power generation was increased from 100s of nW to µW levels with the addition of 0.2 wt. % particles into the getter. Nanowatt-scale sensor platforms were demonstrated with the µW BV devices and the maximum possible lifetime of such platforms was estimated. As this technique enables higher power density BV devices from conventional Si semiconductors (compared to wider bandgap BVs), the further implementation may lower the barrier-to-deployment of these long-life power/sensor platforms.
Tracing the flow of solid matter during an explosion requires a rugged tag that can be measured by a unique identifiable signature. Silica-covered semiconductor quantum dots (QDs) provide a unique and tunable photoluminescent signature that emits from within a sacrificial outer layer. Five types of silica-covered zinc sulfide QDs were synthesized and covalently bound to commercial luminescent powders. The combination of five dots and five powders enables a matrix of 25 unique tags. The tracers are shown to be tolerant of environments associated with chemical explosives and provides a unique tag to evaluate debris fields.