Engineering Papers⌕ Search

Engineering topics

Helms, H. E.

Publications and source records attributed to Helms, H. E..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Ceramic applications in turbine engines

The application of ceramic components to demonstrate improved cycle efficiency by raising the operating temperature of the existing Allison IGI 404 vehicular gas turbine engine is discussed. This effort was called the Ceramic Applications in Turbine Engines (CATE) program and has successfully demonstrated ceramic components. Among these components are two design configurations featuring stationary and rotating caramic components in the IGT 404 engine. A complete discussion of all phases of the program, design, materials development, fabrication of ceramic components, and testing-including rig, engine, and vehicle demonstation test are presented. During the CATE program, a ceramic technology base was established that is now being applied to automotive and other gas turbine engine programs. This technology base is outlined and also provides a description of the CATE program accomplishments.

Helms, H. E.↗
NASA NTRS1983

Ceramic components for the AGT 100 engine

Historically, automotive gas turbines have not been able to meet requirements of the marketplace with respect to cost, performance, and reliability. However, the development of appropriate ceramic materials has overcome problems related to a need for expensive superalloy components and to limitations regarding the operating temperature. An automotive gas turbine utilizing ceramic components has been developed by a U.S. automobile manufacturer. A 100-horsepower, two-shaft, regenerative engine geometry was selected because it is compatible with manual, automatic, and continuously variable transmissions. Attention is given to the ceramic components, the ceramic gasifier turbine rotor development, the ceramic gasifier scroll, ceramic component testing, and the use of advanced nondestructive techniques for the evaluation of the engine components.

Helms, H. E.↗
NASA NTRS1983

Advanced Gas Turbine (AGT): Power-train system development

Technical work on the design and effort leading to the testing of a 74.5 kW (100 hp) automotive gas turbine is described. The general effort was concentrated on building an engine for test starting in July. The buildup progressed with only routine problems and the engine was delivered to the test stand 9 July. In addition to the engine build effort, work continued in selected component areas. Ceramic turbine parts were built and tested. Burst tests of ceramic rotors show strengths are approaching that achieved in test bars; proof testing is required for acceptable strength ceramic vanes. Over 25 hours was accumulated on the combustor rig in three test modes: pilot nozzle only, start nozzle, and main nozzle operation. Satisfactory ignition was achieved for a wide range of starting speeds and the lean blowout limit was as low as 0.06 kg/b (0.14 lb/hr). Lean blowout was more a function of nozzle atomization than fuel/air ratio. A variety of cycle points were tested. Transition from start nozzle flow to main nozzle flow was done manually without difficulty. Regenerator parts were qualification tested without incident and the parts were assembled on schedule. Rig based performance matched first build requirements. Repeated failures in the harmonic drive gearbox during rig testing resulted in that concept being abandoned for an alternate scheme.

Helms, H. E.↗
NASA NTRS1982

Ceramic applications in turbine engines

In the past the potential of vehicular gas engines could not be realized because component materials served to limit the turbine operating temperature, thereby restricting fuel economy and initial cost. It was, therefore, not possible for the vehicular gas turbine to compete with more conventional engines. The emergence of low-cost, high-temperature ceramic components has the potential to reverse this situation. For example, the Allison GT404 engine, operating with ceramic components at turbine inlet temperatures up to 2350 F to 2500 F, has the potential of a fuel economy which is better than that of current Diesel engines. The Allison AGT100 engine operating with ceramic components offers the possibility of a 30% improvement in fuel economy over 1985 spark ignition engines. The materials considered for an employment in the ceramic components include silicon carbide, silicon nitride, aluminum silicate, and lithium aluminum silicate.

Byrd, J. A.↗
NASA NTRS1982

Advanced Gas Turbine (AGT) power-train system development

Technical work on the design and component testing of a 74.5 kW (100 hp) advanced automotive gas turbine is described. Selected component ceramic component design, and procurement were tested. Compressor tests of a modified rotor showed high speed performance improvement over previous rotor designs; efficiency improved by 2.5%, corrected flow by 4.6%, and pressure ratio by 11.6% at 100% speed. The aerodynamic design is completed for both the gasifier and power turbines. Ceramic (silicon carbide) gasifier rotors were spin tested to failure. Improving strengths is indicated by burst speeds and the group of five rotors failed at speeds between 104% and 116% of engine rated speed. The emission results from combustor testing showed NOx levels to be nearly one order of magnitude lower than with previous designs. A one piece ceramic exhaust duct/regenerator seal platform is designed with acceptable low stress levels.

Helms, H. E.↗
NASA NTRS1981

Advanced Gas Turbine (AGT) powertrain system

A 74.5 kW(100 hp) advanced automotive gas turbine engine is described. A design iteration to improve the weight and production cost associated with the original concept is discussed. Major rig tests included 15 hours of compressor testing to 80% design speed and the results are presented. Approximately 150 hours of cold flow testing showed duct loss to be less than the design goal. Combustor test results are presented for initial checkout tests. Turbine design and rig fabrication is discussed. From a materials study of six methods to fabricate rotors, two have been selected for further effort. A discussion of all six methods is given.

Helms, H. E.↗
NASA NTRS1980

Advanced Gas Turbine Powertrain System Development Project

A progress report on the Advanced Gas Turbine Powertrain System Development Project being performed under contract from NASA Lewis is presented. The goals and objectives of the project are described noting that funds from the DOE, Office of Transportation Programs are used to sponsor the project. Among the demonstration objectives are attaining a fuel economy of 42.5 miles per gallon in a 1985 Pontiac Phoenix, multifuel capability, and emission levels within the federal standards. Design objectives examined include competitive reliability and life as well as competitive initial and life cycle costs. Finally, it is stressed that high risk and key elements in this advanced powertrain project are the development of ceramic turbine engine components and the aerodynamic development of small size turbine components.

Helms, H. E.↗
NASA NTRS1977

Study and program plan for improved heavy duty gas turbine engine ceramic component development

Fuel economy in a commercially viable gas turbine engine was demonstrated through use of ceramic materials. Study results show that increased turbine inlet and generator inlet temperatures, through the use of ceramic materials, contribute the greatest amount to achieving fuel economy goals. Improved component efficiencies show significant additional gains in fuel economy.

Helms, H. E.↗
NASA NTRS1972

Stoichiometric gas turbines - Development problems.

Detroit Diesel Allison has been active in demonstrating the feasibility of stoichiometric gas turbine engines for many years. Results of this program are presented with emphasis placed on areas requiring additional development work. Cooling air usage, the effect of cooling air on turbine efficiency, fabrication (materials) methods, and control (instrumentation) techniques are the areas discussed and illustrated. Lamilloy, a pseudo-transpiring material developed by Allison, is discussed in detail.

Helms, H. E.↗