Engineering topics

Harries, W. L.

Publications and source records attributed to Harries, W. L..

At least 19 records

NASA NTRS1990

Studies of molecular properties of polymeric materials

Aerospace environment effects (high energy electrons, thermal cycling, atomic oxygen, and aircraft fluids) on polymeric and composite materials considered for structural use in spacecraft and advanced aircraft are examined. These materials include Mylar, Ultem, and Kapton. In addition to providing information on the behavior of the materials, attempts are made to relate the measurements to the molecular processes occurring in the material. A summary and overview of the technical aspects are given along with a list of the papers that resulted from the studies. The actual papers are included in the appendices and a glossary of technical terms and definitions is included in the front matter.

Harries, W. L.↗

NASA NTRS1989

Laser-powered Martian rover

Two rover concepts were considered: an unpressurized skeleton vehicle having available 4.5 kW of electrical power and limited to a range of about 10 km from a temporary Martian base and a much larger surface exploration vehicle (SEV) operating on a maximum 75-kW power level and essentially unrestricted in range or mission. The only baseline reference system was a battery-operated skeleton vehicle with very limited mission capability and range and which would repeatedly return to its temporary base for battery recharging. It was quickly concluded that laser powering would be an uneconomical overkill for this concept. The SEV, on the other hand, is a new rover concept that is especially suited for powering by orbiting solar or electrically pumped lasers. Such vehicles are visualized as mobile habitats with full life-support systems onboard, having unlimited range over the Martian surface, and having extensive mission capability (e.g., core drilling and sampling, construction of shelters for protection from solar flares and dust storms, etc.). Laser power beaming to SEV's was shown to have the following advantages: (1) continuous energy supply by three orbiting lasers at 2000 km (no storage requirements as during Martian night with direct solar powering); (2) long-term supply without replacement; (3) very high power available (MW level possible); and (4) greatly enhanced mission enabling capability beyond anything currently conceived.

Harries, W. L.↗

NASA NTRS1989

Mechanism of electrical conductivity in an irradiated polyimide

A polyimide was exposed to 1.0 MeV electron radiation. The radiation-induced radical density and dc conductivity were measured at various post-irradiation times. The radiation-induced radical density was found to be correlated to the increased dc conductivity through a hopping model of conductivity. The post-irradiation radical species were identified.

Ries, H. R.↗

NASA NTRS1985

Studies of molecular properties of polymeric materials: Aerospace environmental effects on three linear polymers

The development of crystal handling techniques for reflection infrared spectroscopy and methods for the fabrication and testing of tensile specimens are discussed. Data from mechanical, ac and dc electrical, and electron paramagnetic resonance studies conducted to determine the effects of 0.1-MeV and 1.0-MeV electron radiation on Mylar, Kapton, Ultem, and metal-doped Ultem are presented. Total doses ranging from 1 X 10 to the 8 rads to 1 X 10 to the 10 rads and dose rates from 5 X 10 to the 7 rads/hr to 1 X 10 to the 9 rads/hr were employed. The results of a study on the effects of aircraft service-environment fluids on Ultem are also reported. The weights and mechanical properties of Ultem were evaluated before and after exposure to water, JP4, Skydrol, an antifreeze, and a paint stripper.

Harries, W. L.↗

NASA NTRS1985

Radio-frequency electrical properties of some neat and metal-doped polyimides

As the size and complexity of aerospace systems increase, the uses of polymers are also expected to increase. Polyimides constitute one promising generic class of polymeric materials. They retain good mechanical and physical properties at higher temperatures and absorb less moisture than do the epoxies, which are the polymers most frequently used in present aerospace systems. The properties of these polyimide materials are, therefore, of considerable interest to the aerospace community. Of particular importance are the electrical properties because these properties relate to both electrical and structural applications.

Long, E. R., Jr.↗

NASA NTRS1985

Criteria for the evaluation of laser solar energy converter systems

Assuming that a parabolic insolation-collection mirror-based solar pumped laser has a collector and heat emitter whose weights are proportional to their areas, and that the weight of the laser is negligible by comparison, the output power/unit weight can be expressed in terms of the efficiencies and working temperatures of the system. This ratio appears to be several times higher for an IBr laser than for one operating on C3F7I, because the solar utilization efficiency is greater for the former despite its lower working temperature.

Harries, W. L.↗

NASA NTRS1985

Analytical investigation of cavity blackbody lasers

The characteristics of an ideal blackbody cavity lasant were outlined. The choice of an ideal lasant is a complex process depending on a large number of factors, including the choice of a cooling medium and a buffer gas. Planck's radiation law limits the power input per unit area into a CO2 blackbody cavity laser making the surface area for high powered lasers excessively large. It is suggested that an alternative application might be small 1 W lasers for communication and surveillance, because it would be easy to maintain the cavity temperatures in synchronous orbits where 72 minutes each day are spent in the Earth's shadow.

Harries, W. L.↗

NASA NTRS1985

Theoretical studies of solar-pumped lasers

The power output of a black body solar-pumped laser as a function of time (computer graphic solutions) and under steady state conditions (analytic conditions); computer analyses of polymerization using lasers; and metallic sodium as a laser medium were studied.

Harries, W. L.↗

NASA NTRS1984

Theoretcial studies of solar-pumped lasers

A method of pumping a COhZ laser by a hot cavity was demonstrated. The cavity, heated by solar radiation, should increase the efficiency of solar pumped lasers used for energy conversion. Kinetic modeling is used to examine the behavior of such a COhZ laser. The kinetic equations are solved numerically vs. time and, in addition, steady state solutions are obtained analytically. The effect of gas heating filling the lower laser level is included. The output power and laser efficiency are obtained as functions of black body temperature and gas ratios (COhZ-He-Ar) and pressures. The values are compared with experimental results.

Harries, W. L.↗

NASA NTRS1984

Theoretical studies of solar-pumped lasers

In any lasing medium the emission wavelength should be chosen where there is little self absorption. As emission and absorption spectra for metallic vapors did not seem available, therefore, estimates were made of these cross sections for sodium vapor as functions of wavelength. Although absolute values were not obtained, information on where the emission wavelength should occur became evident. The method of obtaining quantities proportional to the cross sections versus wavelength is outlined. A further comparison based on alternative expressions for the absorption and emission cross sections over a limited wavelength range is made.

Harries, W. L.↗

NASA NTRS1983

Theoretical studies of solar-pumped lasers

Metallic vapor lasers of Na2 and Li2 are examined as solar energy converters. The absorbed photons cause transitions to vibrational-rotational levels in an upper electronic state. With broad band absorption the resultant levels can have quantum numbers considerably higher than the upper lasing level. The excited molecule then relaxes to the upper lasing level which is one of the lower vibrational levels in the upper electronic state. The relaxation occurs from collisions, provided the molecule is not quenched into the ground level electronic state. Lasing occurs with a transition to a vibrational level in the lower electronic state. Rough estimates of solar power efficiencies are 1 percent for Na2 and probably a similar figure for Li2. The nondissociative lasers from a family distinct from materials which dissociate to yield an excited atom.

Harries, W. L.↗

NASA NTRS1983

Theoretical studies of solar-pumped lasers

Possible types of lasers were surveyed for solar power conversion. The types considered were (1) liquid dye lasers, (2) vapor dye lasers, and (3) nondissociative molecular lasers. These are discussed.

Harries, W. L.↗

NASA NTRS1983

Kinetic modeling of an IBr solar pumped laser

The possibility of using an IBr laser as a solar-energy converter is examined theoretically, and reasons for its choice are given. Broadband absorption results in dissociation with the formation of excited metastable Br atoms, some of which then lase to the ground state Br. The ground state is depopulated by three-body recombination and, more importantly, by exchange reactions which more than compensate for the high quenching in heteronuclear halogen systems. Kinetic modeling indicates lasing is possible in the pulsed mode and possibly in the steady state with a cooled gas flow system. Temperature effects are discussed. The efficiency of the laser approaches 1.2 percent at optical thicknesses large enough for complete absorption of the photons.

Harries, W. L.↗

NASA NTRS1982

Theoretical studies of solar-pumped lasers

Solar-pumped lasers were investigated by comparing experimental results from pulse experiments with steady state calculations. The time varying behavior of an IBr laser is studied. The analysis is only approximate, but indicates that conditions occurring in a pulsed experiment are quite different from those at steady state. The possibility of steady-state lasing in an IBr laser is determined. The effects of high temperatures on the quenching and recombination rates are examined. Although uncertainties in the values of the rate coefficients make it difficult to draw firm conclusions, it seems steady state running may be possible at high temperatures.

Harries, W. L.↗

NASA NTRS1981

Theoretical studies of solar-pumped lasers

Estimates of the absorption and emission characteristics of molecules required to develop materials for solar-pumped lasers are addressed. These characteristics are described in terms of the Franck Condon factors, which are calculated from the molecular wave functions. Wave functions for vibrational levels in the lower and upper electronic states of I2 and NSe are calculated numerically and methods of checking errors discussed. Errors arise when the vibrational quantum numbers are high; but, using a calculated rather than measured value of the dissociation energy, wave functions up to the fiftieth vibrational level are obtained. A numerical method of evaluating the wave functions is given, which should be more accurate in the region of electronic transitions during absorption. Franck Condon factors, plotted versus the wavelength of the absorbed photons, are shown, and a check on the Franck Condon factors is made using the vibrational sum rule.

Harries, W. L.↗

NASA NTRS1981

Solar-pumped electronic-to-vibrational energy transfer lasers

The possibility of using solar-pumped lasers as solar energy converters is examined. The absorbing media considered are halogens or halogen compounds, which are dissociated to yield excited atoms, which then hand over energy to a molecular lasing medium. Estimates of the temperature effects for a Br2-CO2-He system with He as the cooling gas are given. High temperatures can cause the lower energy levels of the CO2 laser transition to be filled. The inverted populations are calculated and lasing should be possible. However, the efficiency is less than 0.001. Examination of other halogen-molecular lasant combinations (where the rate coefficients are known) indicate efficiencies in all cases of less than 0.005.

Harries, W. L.↗

NASA NTRS1979

Nuclear-pumped He/3/-Ar laser modeling

A first-order model of He(3)-Ar 1.79-micron laser is developed, compared to experimental results, and used to explain the qualitative features of this system. Results indicate that direct excitation of the argon upper level is at best very inefficient for population inversion. For argon concentrations which give the most efficient laser operation, the He-3(n,p)He-3(n,p)He-3 energy is used to produce atomic He ions that quickly convert into He molecular ions. These molecular ions subsequently form argon atomic ions through charge transfer. The dominant pumping mechanism is collisional-radiative recombination of the argon atomic ion and subsequent radiative cascading into the upper laser level.

Wilson, J. W.↗

NASA NTRS1979

Fission-induced plasmas

The possibility of creating a plasma from fission fragments, and to utilize the energy of the particles to create population inversion that would lead to laser action is investigated. An investigation was made of various laser materials which could be used for nuclear-pumped lasing. The most likely candidate for a fissioning material in the gaseous form is uranium hexafluoride - UF6, and experiments were performed to investigate materials that would be compatible with it. One of the central problems in understanding a fission-induced plasma is to obtain a model of the electron behavior, and some preliminary calculations are presented. In particular, the rates of various processes are discussed. A simple intuitive model of the electron energy distribution function is also shown. The results were useful for considering a mathematical model of a nuclear-pumped laser. Next a theoretical model of a (3)He-Ar nuclear-pumped laser is presented. The theory showed good qualitative agreement with the experimental results.

Harries, W. L.↗