Engineering topics
Publications and source records attributed to Gold, H..
Neither sensing line restrictors nor frictional dampers are required for stability. Analysis presents method by which stability margin, response, and droop magnitude can be incorporated during design of direct-acting hydraulic pressure regulators.
Progress in explaining variations of power experienced in the on-line operation of a 100 kW experimental wind turbine-generator is reported. Data are presented that show the oscillations tend to be characteristic of a wind-driven synchronous generator because of low torsional damping in the power train, resonances of its large structure, and excitation by unsteady and nonuniform wind flow. The report includes dynamic analysis of the drive-train torsion, the generator, passive driveline damping, and active pitch control as well as correlation with experimental recordings. The analysis assumes one machine on an infinite bus with constant generator-field excitation.
A fuel control system is reported for automotive-type gas turbines and particulary advanced gas turbines utilizing variable geometry components to improve mileage and reduce pollution emission. The fuel control system compensates for fuel density variations, inlet temperature variations, turbine vane actuation, acceleration, and turbine braking. These parameters are utilized to control various orifices, spool valves and pistons.
Wind speed variation, tower blockage and structural and inertial factors produce unsteady torque in wind turbines. Methods for modifying the turbine torque so that steady torque is delivered to the coupled ac generator are discussed. The method that may evolve will be influenced by the power use that develops and the trade-offs of cost, weight and complexity.
A direct-acting hydraulic pressure regulator design which incorporates stability margin, response and droop margin is developed. The pressure regulator system does not involve a nonlinear sensing line restrictor (which may degrade transient response) or linear damping (which is sensitive to clearance and viscosity). The direct-acting hydraulic pressure regulator makes use of the technique of lead network stabilization (i.e., the tuned stabilizer concept). An analytically derived circuit pressure regulator is tested to study the stability limit under a parallel capacitive plus resistive load and the stabilizing effect of the tuned stabilizer.
Parameters controlled in design determine the stability of hydraulic pressure regulators in service. The non-linear sensing line restrictor can provide stability, but degrades the transient response. Linear damping is not always physically realizable and is sensitive to clearance and viscosity. Design relationships are analytically derived through which regulators can be made to be stable without the use of either of these damping means. The analytical distinctions between the parameters derived and those in prior literature are discussed. An analytically derived circuit component that stabilizes an otherwise unstable regulator and its experimental verification is described.
Explore the source record for details and available documents.
Reduction in the complexity of gas turbine fuel controls without loss of control accuracy, reliability, or effectiveness as a method for reducing engine costs is discussed. A description and analysis of hydromechanical approach are presented. A computer simulation of the control mechanism is given and performance of a physical model in engine test is reported.
Cost reduction in aircraft turbine engines may be obtained through performance reductions that are acceptable for ranges that are considerably shorter than the range for which current and costly engines were developed. Cost reduction in the fuel control for these cost engines must be achieved without significant performance reduction. This paper describes a fuel control approach that appears to meet this requirement and reviews the work that has been performed on it over the past few years.
A hydromechanical approach to the problem of reducing the compexity and cost of turbine fuel controls without impairing performance and reliability is described and analyzed. The study applies to the modification of long-range high-performance turbine engines to meet short-range missile requirements. The generalized acceleration and deceleration control parameters are studied, and variable-orifice relations for acceleration and deceleration limits are derived. The hydromechanical speed-sensing and multiplying circuit and the fuel control schematic diagram are discussed.
Considerable interest has been generated recently in low cost jet propulsion systems. One of the more complicated components of jet engines is the fuel control. Results of an effort to develop a simpler hydromechanical fuel control are presented. This prototype fuel control was installed on a J85-GE-13 jet engine. Results show that the fuel control provided satisfactory engine performance at sea level static conditions over its normal nonafterburning operating range, including startup. Results of both bench and engine tests are presented; the difficulties encountered are described.
The results of analog and digital computer studies of a low-pressure-ratio turbojet engine system for use in a drone vehicle are presented. The turbojet engine consists of a four-stage axial compressor, single-stage turbine, and a fixed area exhaust nozzle. Three simplified fuel schedules and a generalized parameter fuel control for the engine system are presented and evaluated. The evaluation is based on the performance of each schedule or control during engine acceleration from a windmill start at Mach 0.8 and 6100 meters to 100 percent corrected speed. It was found that, because of the higher acceleration margin permitted by the control, the generalized parameter control exhibited the best dynamic performance.
Cost reduction concepts in gas turbine engine design and fabrication for general aviation aircraft
Cost reduction procedures for aircraft turbine engines used in civil aviation
Development and characteristics of low cost engines for general aviation aircraft
Computer and engine performance study of jet engine generalized parameter fuel control
Flight test of WASP rocket to study slosh dynamics in near zero gravity
Ion thrustor flight test using SERT I spacecraft flown into trajectory by Scout Launch vehicle