Engineering Papers⌕ Search

Engineering topics

Feit, M D

Publications and source records attributed to Feit, M D.

At least 19 records

Thermal annealing of laser damage precursors on fused silica surfaces

Previous studies have identified two significant precursors of laser damage on fused silica surfaces at fluences <35 J/cm2: photoactive impurities from polishing and surface fractures. We evaluate isothermal heating as a means of remediating the defect structure associated with surface fractures. Vickers indentations are applied to silica surfaces at loads between 0.5 and 10 N, creating fracture networks. The indentations are characterized before and following thermal annealing under various time and temperature conditions using confocal time-resolved photo-luminescence (CTP) imaging, and R/1 damage testing with 3-ns, 355-nm laser pulses. Improvements in the damage thresholds with reductions in CTP intensity are observed at temperatures well below the glass transition temperature (Tg). The damage threshold on 0.5-N indentations improves from <8 to >35 J/cm2 after annealing at approximately 750°C. Larger fracture networks require longer or higher temperature treatment to achieve similar results. At an annealing temperature >1100°C, optical microscopy indicates morphological changes in some of the fractures surrounding the indentations, although remnants of the original fractures are still observed. In conclusion, we demonstrate the potential of using isothermal annealing to improve the laser damage resistance of silica optics, and provide a means of further understanding the physics of optical damage and mitigation.

36 MATERIALS SCIENCE↗

Searching for optimal mitigation geometries for laser-resistant multilayer high-reflector coatings

Growing laser damage sites on multilayer high-reflector coatings can limit mirror performance. One of the strategies to improve laser damage resistance is to replace the growing damage sites with predesigned benign mitigation structures. By mitigating the weakest site on the optic, the large-aperture mirror will have a laser resistance comparable to the intrinsic value of the multilayer coating. To determine the optimal mitigation geometry, the finite-difference time-domain method was used to quantify the electric-field intensification within the multilayer, at the presence of different conical pits. We find that the field intensification induced by the mitigation pit is strongly dependent on the polarization and the angle of incidence (AOI) of the incoming wave. Therefore, the optimal mitigation conical pit geometry is application specific. Furthermore, our simulation also illustrates an alternative means to achieve an optimal mitigation structure by matching the cone angle of the structure with the AOI of the incoming wave, except for the p-polarized wave at a range of incident angles between 30 deg. and 45 deg.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Assessment of Molecular Dynamic Force Fields for Silica for Use in Simulating Laser Damage Mitigation

We compare force fields (FF's) that have been used in molecular dynamic (MD) simulations of silica in order to assess their applicability for use in simulating IR-laser damage mitigation. Although pairwise FF?s obtained by fitting quantum mechanical calculations such as the BKS and CHIK potentials have been shown to reproduce many of the properties of silica including the stability of silica polymorphs and the densification of the liquid, we show that melting temperatures and fictive temperatures are much too high. Softer empirical force fields give liquid and glass properties at experimental temperatures but may not predict all properties important to laser mitigation experiments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Densification and residual stress induced by CO2 laser-based mitigation of SiO2 surfaces

Knowing the ultimate surface morphology resulting from CO{sub 2} laser mitigation of induced laser damage is important both for determining adequate treatment protocols, and for preventing deleterious intensification upon subsequent illumination of downstream optics. Physical effects such as evaporation, viscous flow and densification can strongly affect the final morphology of the treated site. Evaporation is a strong function of temperature and will play a leading role in determining pit shapes when the evaporation rate is large, both because of material loss and redeposition. Viscous motion of the hot molten material during heating and cooling can redistribute material due to surface tension gradients (Marangoni effect) and vapor recoil pressure effects. Less well known, perhaps, is that silica can densify as a result of structural relaxation, to a degree depending on the local thermal history. The specific volume shrinkage due to structural relaxation can be mistaken for material loss due to evaporation. Unlike evaporation, however, local density change can be reversed by post annealing. All of these effects must be taken into account to adequately describe the final morphology and optical properties of single and multiple-pass mitigation protocols. We have investigated, experimentally and theoretically, the significance of such densification on residual stress and under what circumstances it can compete with evaporation in determining the ultimate post treatment surface shape. In general, understanding final surface configurations requires taking all these factors including local structural relaxation densification, and therefore the thermal history, into account. We find that surface depressions due to densification can dominate surface morphology in the non-evaporative regime when peak temperatures are below 2100K.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fracture Induced Sub-Band Absorption as a Precursor to Optical Damage on Fused Silica Surfaces

The optical damage threshold of indentation induced flaws on fused silica surfaces was explored. Mechanical flaws were characterized by laser damaged testing, SEM, optical, and photoluminescence microscopy. Localized polishing, chemical etching, and the control of indentation morphology were used to isolate the structural features which limit optical damage. A thin defect layer on fracture surfaces, including those smaller than the wavelength of visible light, was found to be the dominant source of laser damage initiation during illumination with 355nm, 3ns laser pulses. Little evidence was found that either displaced or densified material or fluence intensification plays a significant role in optical damage at fluences >35J/cm{sup 2}. Elimination of the defect layer was shown to increase the overall damage performance of fused silica optics.

36 MATERIALS SCIENCE↗

HF-based etching processes for improving laser damage resistance of fused silica optical surfaces

The effect of various HF-based etching processes on the laser damage resistance of scratched fused silica surfaces has been investigated. Conventionally polished and subsequently scratched fused silica plates were treated by submerging in various HF-based etchants (HF or NH{sub 4}F:HF at various ratios and concentrations) under different process conditions (e.g., agitation frequencies, etch times, rinse conditions, and environmental cleanliness). Subsequently, the laser damage resistance (at 351 or 355 nm) of the treated surface was measured. The laser damage resistance was found to be strongly process dependent and scaled inversely with scratch width. The etching process was optimized to remove or prevent the presence of identified precursors (chemical impurities, fracture surfaces, and silica-based redeposit) known to lead to laser damage initiation. The redeposit precursor was reduced (and hence the damage threshold was increased) by: (1) increasing the SiF{sub 6}{sup 2-} solubility through reduction in the NH4F concentration and impurity cation impurities, and (2) improving the mass transport of reaction product (SiF{sub 6}{sup 2-}) (using high frequency ultrasonic agitation and excessive spray rinsing) away from the etched surface. A 2D finite element crack-etching and rinsing mass transport model (incorporating diffusion and advection) was used to predict reaction product concentration. The predictions are consistent with the experimentally observed process trends. The laser damage thresholds also increased with etched amount (up to {approx}30 {micro}m), which has been attributed to: (1) etching through lateral cracks where there is poor acid penetration, and (2) increasing the crack opening resulting in increased mass transport rates. With the optimized etch process, laser damage resistance increased dramatically; the average threshold fluence for damage initiation for 30 {micro}m wide scratches increased from 7 to 41 J/cm{sup 2}, and the statistical probability of damage initiation at 12 J/cm{sup 2} of an ensemble of scratches decreased from {approx}100 mm{sup -1} of scratch length to {approx}0.001 mm{sup -1}.

42 ENGINEERING↗

Modeling of light intensification by conical pits within multilayer coatings

Removal of laser-induced damage sites provides a possible mitigation pathway to improve damage resistance of coated multilayer dielectric mirrors. In an effort to determine the optimal mitigation geometry which will not generate secondary damage precursors, the electric field distribution within the coating layers for a variety of mitigation shapes under different irradiation angles has been estimated using the finite difference time domain (FDTD) method. The coating consists of twenty-four alternating layers of hafnia and silica with a quarter-wave reflector design. A conical geometrical shape with different cone angles is investigated in the present study. Beam incident angles range from 0{sup o} to 60{sup o} at 5{sup o} increments. We find that light intensification (square of electric field, |E|{sup 2}) within the multilayers depends strongly on the beam incident direction and the cone angle. By comparing the field intensification for each cone angle under all angles of incidence, we find that a 30{sup o} conical pit generates the least field intensification within the multilayer film. Our results suggest that conical pits with shallow cone angles ({le} 30{sup o}) can be used as potential optimal mitigation structures.

42 ENGINEERING↗

Ultra-fast photoluminescence as a diagnostic for laser damage initiation

Using high-sensitivity confocal time-resolved photoluminescence (CTP) techniques, we report an ultra-fast photoluminescence (40ps-5ns) from impurity-free surface flaws on fused silica, including polished, indented or fractured surfaces of fused silica, and from laser-heated evaporation pits. This fast photoluminescence (PL) is not associated with slower point defect PL in silica which has characteristic decay times longer than 5ns. Fast PL is excited by the single photon absorption of sub-band gap light, and is especially bright in fractures. Regions which exhibit fast PL are strongly absorptive well below the band gap, as evidenced by a propensity to damage with 3.5eV ns-scale laser pulses, making CTP a powerful non-destructive diagnostic for laser damage in silica. The use of CTP to provide insights into the nature of damage precursors and to help develop and evaluate new damage mitigation strategies will be presented.

42 ENGINEERING↗