Engineering topics
Publications and source records attributed to Dorsch, R. G..
Noise tests were conducted using simulated mixer-type nozzles and a small scale model of an externally blown flap, lift augmentation system. The mixer nozzles were simulated with orifice plates.
Explore the source record for details and available documents.
NASA research and development work on the noise of aircraft engines suitable for use on conventional take-off and landing subsonic cruise airplanes is reviewed. The work discussed was part of the NASA Quiet Engine program. Salient results in the areas of fan, jet and complete propulsion system noise are presented and briefly discussed.
Preliminary acoustic tests of the engine-over-the-wing concept as a method for reducing the aerodynamic noise created by conventional and short takeoff aircraft are discussed. Tests were conducted with a small wing section model having two flaps which can be set for either the landing or takeoff positions. Data was acquired with the flaps set at 10 degrees and 20 degrees for takeoff and 30 and 60 degrees for landing. The engine exhaust was simulated by an air jet from a convergent nozzle. Far field noise data are presented for nominal pressure ratios of 1.25, 1.4 and 1.7 for both the flyover and sideline modes.
Noise data were obtained with a model of an externally blown flap of the type that is currently being considered for STOL aircraft. The noise caused by impingement of the jet on the flap is much louder than the nozzle jet noise. It is especially so directly below the wing. The noise level increases as the jet velocity and flap angle are increased. The sound power level increased with the sixth power of velocity. Several physical variations to the STOL model configuration were also tested. Two such variations, a large board and a slotless curved plate wing, had the same power spectra density (Strouhal number curve) as the model.
The results of preliminary acoustic tests of the engine over the wing concept are summarized. The tests were conducted with a small wing section model (32 cm chord) having two flaps set at the landing position, which is 30 and 60 deg respectively. The engine exhaust was simulated by an air jet from a convergent nozzle having a nominal diameter of 5.1 centimeters. Factors investigated for their effect on noise include nozzle location, wing shielding, flap leakage, nozzle shape, exhaust deflectors, and internally generated exhaust noise.
A summary is given of the noise suppression tests conducted for the STOL aircraft. The tests were made using a large scale mixer nozzle and externally blown flap model. Data were obtained over a range of nozzle exhaust velocities (172 to 284 m/sec) and flap angles. Comparisons were made between the results of the mixer nozzle and those obtained with a standard single convergent nozzle. The resulting conclusions show that a reduction in noise level did occur using the mixer nozzle system.
Noise data were obtained with a large externally blown flap model. A fan-jet engine exhaust was simulated by a 1/2-scale bypass nozzle supplied by pressurized air. The nozzle was pylon mounted on a wing section having a double-slotted flap for lift augmentation. Noise radiation patterns and spectra were obtained for nozzle exhaust velocities between 400 and 1150 ft/sec. The blown flap noise data are in good agreement with previous small model results extrapolated to test conditions by Strouhal scaling. The results indicate that blown flap noise must be suppressed to meet STOL aircraft noise goals.
Noise data were obtained with a large externally blown flap model. A fan-jet engine exhaust was simulated by a 1/2-scale bypass nozzle supplied by pressurized air. The nozzle was pylon mounted on a wing section having a double-slotted flap for lift augmentation. Noise radiation patterns and spectra were obtained for nozzle exhaust velocities between 400 and 1150 ft/sec. The blown flap noise data are in good agreement with previous small model results extrapolated to test conditions by Strouhal scaling. The results indicate that blown flap noise must be suppressed to meet STOL aircraft noise goals.
The noise caused by the interaction of the jet exhaust and a wing was measured under static conditions for several versions of a small-scale STOL engine-over-the-wing configuration. Three basic nozzles were used in the tests; a circular nozzle, a 5:1 aspect ratio slot nozzle and a 10:1 aspect ratio slot nozzle. Various flow attachment devices were included in the study. The wing included a flap that could be positioned for nominal takeoff or approach flap settings. Far field noise data are presented for the flyover mode. The data are discussed in terms of sound power and sound pressure spectra. Implications of extending the small-scale model acoustic data to full-scale aircraft are discussed briefly and indicate a sizeable flyover noise attenuation may be achieved due to shielding by the wing.
Externally-blown-flap noise research can be summarized by the following remarks: With lower-surface blowing, the sources of the flap noise are begining to be understood and the noise scaling laws have been established. Further, progress has been made on suppressing the flap interaction noise at the large flap deflections used during landing. Recent small-scale noise tests of configurations using external upper-surface blowing indicate that engine-over-the-wing configurations may be promising.
Screening tests of upper surface blowing on externally blown flaps configurations were conducted. Noise and turning effectiveness data were obtained with small-scale, engine-over-the-wing models. One large model was tested to determine scale effects. Nozzle types included circular, slot, D-shaped, and multilobed. Tests were made with and without flow attachment devices. For STOL applications the particular multilobed mixer and the D-shaped nozzles tested were found to offer little or no noise advantage over the round convergent nozzle. High aspect ratio slot nozzles provided the quietest configurations. In general, upper surface blowing was quieter than lower surface blowing for equivalent EBF models.
Noise tests of externally blown flaps with the engine under the wing and engine over the wing configurations were conducted. Flap noise data obtained on a TF-34 aircraft are discussed. Noise data obtained during a free-jet forward-speed-effect analysis are presented. Noise sources associated with upper surface flap blowing are described. Results of a small scale configuration screening study and some large scale model test data are analyzed. The noise data for the engine over wing configurations are compared with the engine under the wing configurations.
Noise measurement data on various types of blown flap configurations for STOL aircraft, discussing integration effects between jet and flap assembly
Noise data with models of both internally and externally blown jet flaps designed for STOL aircraft
Noise reduction effectiveness of mixer nozzle for increasing lift capability in STOL aircraft
Space Rankine cycle power systems technology applied to ground-based power systems
Boiler inlet impedance frequency response in single tube heat exchanger when pump-fed with oscillating flow