Engineering topics

Dorsch, R. G.

Publications and source records attributed to Dorsch, R. G..

At least 19 records

NASA NTRS1976

Effect of simulated forward airspeed on small-scale-model externally blown flap noise

Noise tests were conducted on a small-scale model of an externally blown flap lift augmentation system. The nozzle/wing model was subjected to external flow that simulated takeoff and landing flight velocities by placing it in a 33-centimeter-diameter free jet. The results showed that external flow attenuated the noise associated with the various configurations tested. The amount of attenuation depended on flap setting. More attenuation occurred with a trailing-flap setting of 20 deg than with one of 60 deg. Noise varied with relative velocity as a function of the trailing-flap setting and the angle from the nozzle inlet.

Goodykoontz, J. H.↗

NASA NTRS1975

Forward velocity effects on under-the-wing externally blown flap noise

Noise tests were conducted with small-scale models of externally blown-flap powered-lift systems that were subjected to simulated takeoff and landing free-stream velocities by placing the nozzle-wing models in a free jet. The nozzle configurations consisted of a conical and an 8-tube mixer nozzle. The results show that the free-stream velocity attenuates the noise from the various configurations, with the amount of attenuation depending on the flap setting. More attenuation was obtained with a flap setting of 20 degrees than with a flap setting of 60 degrees. The dynamic effect on the total attenuation caused by aircraft motion is also discussed.

Goodykoontz, J.↗

NASA NTRS1975

Interim prediction method for externally blown flap noise

An interim procedure for predicting externally blown flap (EBF) noise spectra anywhere below a powered lift aircraft is presented. Both engine-under-the-wing and engine-over-the-wing EBF systems are included. The method uses data correlations for the overall sound pressure level based on nozzle exit area and exhaust velocity along with OASPL directivity curves and normalized one-third-octave spectra. Aircraft motion effects are included by taking into account the relative motion of the source with respect to the observer and the relative velocity effects on source strength.

Dorsch, R. G.↗

NASA NTRS1974

Interim prediction method for low frequency core engine noise

A literature survey on low-frequency core engine noise is presented. Possible sources of low frequency internally generated noise in core engines are discussed with emphasis on combustion and component scrubbing noise. An interim method is recommended for predicting low frequency core engine noise that is dominant when jet velocities are low. Suggestions are made for future research on low frequency core engine noise that will aid in improving the prediction method and help define possible additional internal noise sources.

Huff, R. G.↗

NASA NTRS1974

Acoustic tests of a 15.2 centimeter-diameter potential flow convergent nozzle

An experimental investigation of the jet noise radiated to the far field from a 15.2-cm-diam potential flow convergent nozzle has been conducted. Tests were made with unheated airflow over a range of subsonic nozzle exhaust velocities from 62 to 310m/sec. Mean and turbulent velocity measurements in the flow field of the nozzle exhaust indicated no apparent flow anomalies. Acoustic measurements yielded data uncontaminated by internal and/or background noise to velocities as low as 152m/sec. Finally, no significantly different acoustic characteristics between the potential flow nozzle and simple convergent nozzles were found.

Karchmer, A. M.↗

NASA NTRS1974

Externally blown flap noise research

The Lewis Research Center cold-flow model externally blown flap (EBF) noise research test program is summarized. Both engine under-the-wing and over-the-wing EBF wing section configurations were studied. Ten large scale and nineteen small scale EBF models were tested. A limited number of forward airspeed effect and flap noise suppression tests were also run. The key results and conclusions drawn from the flap noise tests are summarized and discussed.

Dorsch, R. G.↗

NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both 2- and 3-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-inch diameter conical configurations. These nozzles were tested at two positions below the wing. The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗

NASA NTRS1974

Acoustic characteristics of externally blown flap systems with mixer nozzles

Noise tests were conducted on a large scale, cold flow model of an engine-under-the-wing externally blown flap lift augmentation system employing a mixer nozzle. The mixer nozzle was used to reduce the flap impingement velocity and, consequently, try to attenuate the additional noise caused by the interaction between the jet exhaust and the wing flap. Results from the mixer nozzle tests are summarized and compared with the results for a conical nozzle. The comparison showed that with the mixer nozzle, less noise was generated when the trailing flap was in a typical landing setting (e.g., 60 deg). However, for a takeoff flap setting (20 deg), there was little or no difference in the acoustic characteristics when either the mixer or conical nozzle was used.

Goodykoontz, J. H.↗

NASA NTRS1974

Externally blown flap noise research

Dorsch, R. G.↗

NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both two- and three-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-in.-diam conical configurations. These nozzles were tested at two positions below the wing (19-1/4 and 29-1/4 in.). The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗

NASA NTRS1974

Acoustic characteristics of externally blown flap systems with mixer nozzles

Noise tests were conducted on a large-scale cold-flow model of an engine-under-the-wing externally blown flap lift augmentation system employing a mixer nozzle. The mixer nozzle was used to reduce the flap impingement velocity and, consequently, to try to attenuate the additional noise caused by the interaction between the jet exhaust and the wing flap. Results from the mixer nozzle tests are summarized and compared with the results for a conical nozzle. The comparison showed that, with the mixer nozzle, less noise was generated when the trailing flap was in a typical landing setting (e.g., 60 deg). However, for a takeoff flap setting (20 deg), there was little or no difference in the acoustic characteristics when either the mixer or conical nozzle was used.

Goodykoontz, J. H.↗

NASA NTRS1973

Engine-over-the-wing noise research.

Acoustic measurements for large model engine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdB quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 dB quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗

NASA NTRS1973

Noise tests of a mixer nozzle-externally blown flap system

Noise tests were conducted on a large scale model of an externally blown flap lift augmentation system, employing a mixer nozzle. The mixer nozzle consisted of seven flow passages with a total equivalent diameter of 40 centimeters. With the flaps in the 30 - 60 deg setting, the noise level below the wing was less with the mixer nozzle than when a standard circular nozzle was used. At the 10 - 20 deg flap setting, the noise levels were about the same when either nozzle was used. With retracted flaps, the noise level was higher when the mixer nozzle was used.

Goodykoontz, J. H.↗

NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 feet per second. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise. The total noise power generation was essentially the same for circular, slot, and plug nozzles of good aerodynamic shape. The noise radiation patterns were essentially the same for these nozzle shapes except near the nozzle exhaust axis.

Olsen, W. A.↗

NASA NTRS1973

Engine-over-the-wing noise research

Acoustic measurements for large model eingine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdb quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 db quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗

NASA NTRS1973

Flap noise prediction method for a powered lift system

A method is presented for estimating the noise generated by deflection of the engine exhaust for under-the-wing and over-the-wing versions of an externally blown flap configuration for powered lift. Correlation equations and curves are given for the overall sound pressure level and directivity and for spectra scaled to a high bypass 25,000-pound thrust size engine. Data are taken from TF34 engine tests and from large cold flow model tests. The correlations are empirical, and thus application of this prediction procedure is limited to geometrically similar configurations. Application of the method is illustrated by calculated sample footprints.

Clark, B.↗

NASA NTRS1973

The effect of nozzle inlet shape, lip thickness, and exit shape and size on subsonic jet noise.

Far field noise data were taken for convergent nozzles of various shapes and sizes at subsonic velocities exceeding 400 ft/sec. For a circular nozzle, the nozzle inlet shape and lip thickness had no effect on the noise level, directivity, or spectra when compared at the same nozzle exit diameter and peak exhaust velocity. A sharp edged orifice was one exception to this statement. Coannular nozzles can produce additional high frequency noise. Blunt ended centerbodies, where there is significant base drag, also generate significant additional noise.

Olsen, W. A.↗

NASA NTRS1972

Noise generated by impingement of a jet upon a large flat board

Data were obtained on the noise generated by an air jet impinging on a large flat board. The board was large enough so that the flow leaving the edges of the board generated no significant noise. The impingement angle, nozzle shape and size, jet velocity, and the distance from the nozzle to the board were varied in the experiment. Far-field noise data are presented. The nozzle-alone noise contribution to the total noise was generally small and was subtracted from the total, leaving the impingement-only noise. The impingement-only noise was adequately correlated by eighth power of the peak impingement velocity and first power of the impingement area. The spectral data were correlated by a Strouhal number based on the peak impingement velocity and a characteristic impingement diameter.

Olsen, W. A.↗