Engineering topics

Dominek, A.

Publications and source records attributed to Dominek, A..

12 records

NASA NTRS1995

Material Measurements Using Groundplane Apertures

A technique for material parameter determination using an aperture in a groundplane is studied. The material parameters are found by relating the measured reflected field in the aperture to a numerical model. Two apertures are studied which can have a variety of different material configurations covering the aperture. The aperture cross-sections studied are rectangular and coaxial. The material configurations involved combinations of single layer and dual layers with or without a resistive exterior resistive sheet. The resistivity of the resistive sheet can be specified to simulate a perfect electric conductor (PEC) backing (0 Ohms/square) to a free space backing (infinity Ohms/square). Numerical parameter studies and measurements were performed to assess the feasibility of the technique.

Komisarek, K.↗

NASA NTRS1992

A high-frequency ray analysis of the electromagnetic backscattering by a two-dimensional ogive

The electromagnetic backscattering from a two-dimensional ogive is examined, including a mechanism-by-mechanism account for the scattered field. The uniform theory of diffraction is used in conjunction with a simple creeping wave representation to yield a solution which provides an accurate and continuous backscattering result for a wide range of ogive geometry parameters. Although not a rigorous derivation of higher-order diffraction ceofficients, this solution provides insight into the relative contributions of the various creeping waves which are generated and propagate around the two-dimensional ogive. Comparisons with moment method calculations are used to demonstrate the range of applicability of this high-frequency asymptotic solution.

Shamansky, H.↗

NASA NTRS1991

Analysis of lossy composite terminating structures

A finite element solution and computer code for the electromagnetic scattering of inhomogeneous penetrable bodies is presented. The application for the code is for the analysis and design of leading and trailing edge terminations when conducting and nonconducting materials are used. Examples of simple triangular shaped terminations are also presented.

Andre, R.↗

NASA NTRS1991

Constitutive parameter extraction for heated materials

The focus is the determination of the electrical constitutive paramaters of materials with general complex epsilon and mu values at elevated temperatures. Measurement fixtures and techniques are evaluated for frequencies between 8 and 12 GHz using a rectangular waveguide with the sample completely filling the fixture. Three different measurement techniques are evaluated to obtain the necessary measured quantities for parameter extraction. The most desirable technique used two reflection measurements from material samples of different thickness backed with a short. Temperatures up to 600 F were investigated.

Munk, J.↗

NASA NTRS1989

Electromagnetic properties of material coated surfaces

The electromagnetic properties of material coated conducting surfaces were investigated. The coating geometries consist of uniform layers over a planar surface, irregularly shaped formations near edges and randomly positioned, electrically small, irregularly shaped formations over a surface. Techniques to measure the scattered field and constitutive parameters from these geometries were studied. The significance of the scattered field from these geometries warrants further study.

Beard, L.↗

NASA NTRS1989

Constitutive parameter measurements of lossy materials

The electrical constitutive parameters of lossy materials are considered. A discussion of the NRL arch for lossy coatings is presented involving analytical analyses of the reflected field using the geometrical theory of diffraction (GTD) and physical optics (PO). The actual values for these parameters can be obtained through a traditional transmission technique which is examined from an error analysis standpoint. Alternate sample geometries are suggested for this technique to reduce sample tolerance requirements for accurate parameter determination. The performance for one alternate geometry is given.

Dominek, A.↗

NASA NTRS1989

Electromagnetic properties of ice coated surfaces

The electromagnetic scattering from ice coated structures is examined. The influence of ice is shown from a measurement standpoint and related to a simple analytical model. A hardware system for the realistic measurement of ice coated structures is also being developed to use in an existing NASA Lewis icing tunnel. Presently, initial measurements have been performed with a simulated tunnel to aid in the development.

Dominek, A.↗

NASA NTRS1989

The ogive as a RCS compact range standard

E- and H-plane radar cross section (RCS) patterns at 4 and 10 GHz are provided (based upon moment method calculations) for a perfectly conducting ogive to be used as a compact range verification standard. The dimensions of the ogive are 36 in. and 9.546 in. long with half tip angles of 15 deg and 20 deg, respectively. Comparison between the calculations and measurements are also provided.

Dominek, A.↗

NASA NTRS1988

Measurement of the properties of lossy materials inside a finite conducting cylinder

A computer code was developed to automatically perform swept frequency reflection and transmission measurements using a HP5510B Network Analyzer and computer. This software is used in conjunction with a modified high temperature test rig to obtain reflection measurements from a flat material sample. The software allows data processing to eliminate measurement errors and to obtain a reflection coefficient in the frequency or time domain. A description of the program is presented.

Caldecott, R.↗

NASA NTRS1988

Material parameter determination from scattering measurements

The electrical, macroscopic performance of isotropic material can generally be described through their constitutive scalar parameters, permittivity and permeability which are symbolically represented by epsilon and mu, respectively. These parameters relate the electric and magnetic flux densities to the electric and magnetic fields through the following relationships: (1) D=epsilonE; and (2) B=muH. It is through these parameters that the interaction of electromagnetic waves with material can be quantized in terms of reflection and transmission coefficients, and propagation and attenuation factors.

Dominek, A.↗

NASA NTRS1988

Material parameter measurements at high temperatures

Alternate fixtures of techniques for the measurement of the constitutive material parameters at elevated temperatures are presented. The technique utilizes scattered field data from material coated cylinders between parallel plates or material coated hemispheres over a finite size groundplane. The data acquisition is centered around the HP 8510B Network Analyzer. The parameters are then found from a numerical search algorithm using the Newton-Ralphson technique with the measured and calculated fields from these canonical scatters. Numerical and experimental results are shown.

Dominek, A.↗

NASA NTRS1988

Measurement of the properties of lossy materials inside a finite conducting cylinder

Broadband, swept frequency measurement techniques were investigated for the evaluation of the electrical performance of thin, high temperature material coatings. Reflections and transmission measurements using an HP8510B Network Analyzer were developed for an existing high temperature test rig at NASA Lewis Research Center. Reflection measurements will be the initial approach used due to fixture simplicity even though surface wave transmission measurements would be more sensitive. The minimum goal is to monitor the electrical change of the material's performance as a function of temperature. If possible, the materials constitutive parameters, epsilon and muon will be found.

Dominek, A.↗