Engineering topics

Daniel, I. M.

Publications and source records attributed to Daniel, I. M..

36 records · Page 2

NASA NTRS1981

Development of orthotropic birefringent materials for photoelastic stress analysis

Materials were selected and fabrication procedures developed for orthotropic birefringent materials. An epoxy resin (Maraset 658/558 system) was selected as the matrix material. Fibers obtained from style 3733 glass cloth and type 1062 glass roving were used as reinforcement. Two different fabrication procedures were used. In the first one, layers of unidirectional fibers removed from the glass cloth were stacked, impregnated with resin, bagged and cured in the autoclave at an elevated temperature. In the second procedure, the glass roving was drywound over metal frames, impregnated with resin and cured at room temperature under pressure and vacuum in an autoclave. Unidirectional, angle-ply and quasi-isotropic laminates of two thicknesses and with embedded flaws were fabricated. The matrix and the unidirectional glass/epoxy material were fully characterized. The density, fiber volume ratio, mechanical, and optical properties were determined. The fiber volume ratio was over 0.50. Birefringent properties were in good agreement with predictions based on a stress proportioning concept and also, with one exception, with properties predicted by a finite element analysis.

Daniel, I. M.↗

NASA NTRS1980

Thermal deformations and stresses in composite materials

Residual stresses are induced during curing in angle-ply laminates as a result of anisotropic thermal deformations of the variously oriented plies. Residual strains are measured experimentally using embedded strain gage techniques, and residual stresses are computed using orthotropic stress-strain relations. The results show that, for graphite and Kevlar laminates, residual stresses at room temperature are high enough to cause damage in the plies in the transverse to the fiber direction. It is also shown that residual stresses do not relax appreciably. The ply stacking sequence is found to have no effect on the magnitude of average residual stresses. Residual stresses and susceptibility to cracking during curing depend to a marked extent on ply layup.

Daniel, I. M.↗

NASA NTRS1979

Wave propagation in transversely impacted composite laminates

An experimental study was conducted to determine the wave-propagation characteristics, transient strains and residual properties of unidirectional and angle-ply boron/epoxy and graphite/epoxy laminates impacted with silicon-rubber projectiles at velocities up to 250 m/sec. Results include the following: (1) the predominant wave is the flexural wave propagating at different velocities in different directions; (2) peak strains and strain rates in the transverse to the (outer) fiber direction are much higher than those in the direction of the fibers; (3) strain rates up to 640/sec were measured; and (4) unidirectional laminates under impact showed appreciable modulus and strength degradation in the direction transverse to fibers.

Daniel, I. M.↗

NASA NTRS1979

Fabrication and testing of composite ring specimens

The tooling and techniques used in the fabrication of composite laminate tubes of any desired ply orientation and stacking sequence are described along with techniques for cutting ring specimens under internal pressure. The method consists of laying up the tube on a central circular mandrel, and by means of internal pressure, expanding the prepreg tube against the cavity wall of an external mold tool, which forms the geometric curing envelope for the tube. Tube quality is assessed by laminate wall thickness measurement, by hoop strength measurement on rings cut from the ends of the tube, and by ultrasonic inspection.

Liber, T.↗

NASA NTRS1978

Evaluation of composite flattened tubular specimen

Flattened tubular specimens of graphite/epoxy, S-glass/epoxy, Kevlar-49/epoxy, and graphite/S-glass/epoxy hybrid materials were evaluated under static and cyclic uniaxial tensile loading and compared directly with flat coupon data of the same materials generated under corresponding loading conditions. Additional development for the refinement of the flattened specimen configuration and fabrication was required. Statically tested graphite/epoxy, S-glass/epoxy, and Kevlar 49/epoxy flattened tube specimens exhibit somewhat higher average strengths than their corresponding flat coupons. Flattened tube specimens of the graphite/S-glass/epoxy hybrid and the graphite/epoxy flattened tube specimens failed in parasitic modes with consequential lower strength than the corresponding flat coupons. Fatigue tested flattened tube specimens failed in parasitic modes resulting in lower fatigue strengths than the corresponding flat coupons.

Liber, T.↗

NASA NTRS1978

Edgeless composite laminate specimen for static and fatigue testing

The influence of edge effects on the tensile properties of angle-ply laminate composites can be eliminated by using edgeless (round tubular) specimens. However, uniaxial tests with such specimens, static and fatigue, have been generally unsuccessful because of the differential Poisson effect between the test section and the grips. An edgeless cylindrical specimen, developed to circumvent these difficulties, is examined in the present paper. It is a flattened tube consisting of two flat sides connected by curved sections. It can be handled much like the standard flat coupon. The flat ends of the specimen are provided with crossplied fiberglass gripping tabs, the same as used for flat test coupons. As part of the tabbing, the hollow ends must be plugged with inserts to prevent crushing of the ends. A special insert design was developed to minimize detrimental Poisson effects ordinarily introduced by inserts.

Liber, T.↗

NASA NTRS1978

Testing of fiber composites at high strain rates

An experimental investigation was conducted to determine strain rate effects in fiber composites. Unidirectional composite specimens of boron/epoxy, graphite/epoxy, S-glass/epoxy and Kevlar/epoxy were tested at tensile strain rates of up to 27 m/m/sec. Longitudinal, transverse and in-plane shear properties, including modulus, Poisson's ratio, strength and ultimate strain, were determined by testing 0-, 90and 10-degree unidirectional coupons. Strains were measured by means of strain gages bonded on the coupons and loads were measured by means of a strain gage load cell. All specimens were loaded in an electrohydraulic loading system. The 0-degree properties which are governed by the fibers do not vary much with strain rate except for the Kevlar/epoxy material which shows an increase in both modulus and strength. The strain rate effects on 90-degree properties were small with a general trend toward higher strength with increasing strain rate. The most noticeable effect was on in-plane shear properties with shear strength values at high strain rates approximately fifteen percent higher than static values.

Daniel, I. M.↗

NASA NTRS1977

Mechanical loader for testing composites

Device applies constant preload to environmentally cycled specimens. Loading spring for each specimen has sufficiently large deflection to insure insignificant degree of change in specimen load during thermal cycling.

Daniel, I. M.↗

NASA NTRS1977

Static behavior and the effects of thermal cycling in hybrid laminates

Static stiffness, strength and ultimate strain after thermal cycling were investigated for graphite/Kevlar 49/epoxy and graphite/S-glass/epoxy angle-ply laminates. Tensile stress-strain curves to failure and uniaxial tensile properties were determined, and theoretical predictions of modulus, Poisson's ratio and ultimate strain, based on linear lamination theory, constituent ply properties and measured strength, were made. No significant influence on tensile stress properties due to stacking sequence variations was observed. In general, specimens containing two 0-degree Kevlar or S-glass plies were found to behave linearly to failure, while specimens containing 4 0-degree Kevlar or S-glass plies showed some nonlinear behavior.

Liber, T. M.↗

NASA NTRS1977

Lamination residual strains and stresses in hybrid laminates

An investigation is conducted of the effects of hybridization on the magnitude of lamination residual stresses. Eight-ply graphite/Kevlar 49/epoxy and graphite/S-glass/epoxy laminates were studied. The same matrix resin was selected for all basic materials to ensure compatibility and uniform curing of the various plies. The specimens, with inserted strain gages and thermocouples, were subjected to curing and postcuring cycles in an autoclave. Subsequently, the specimens were subjected to a thermal cycle from room temperature to 444 K and down to room temperature. It was found that hydridizing reduces apparently residual strains and stresses in the graphite plies. However, these strains were not affected much by the type and degree of hybridization.

Daniel, I. M.↗

NASA NTRS1977

Effects of mechanical and thermal cycling on composite and hybrid laminates with residual stresses

The effects of tensile load cycling and thermal cycling on residual stiffness and strength properties of the following composite and hybrid angle-ply laminates were studied: boron/epoxy, boron/polyimide, graphite/low-modulus epoxy, graphite/high-modulus epoxy, graphite/polyimide, S-glass/epoxy, graphite/Kevlar 49/epoxy, and graphite/S-glass/epoxy. Specimens of the first six types were mechanically cycled up to 90% of static strength. Those that survived 10 million cycles were tested statically to failure, and no significant changes in residual strength and modulus were noted. Specimens of all types were subjected to thermal cycling between room temperature and 411 K for the epoxy-matrix composites and 533 K for the polyimide-matrix composites. The residual strength and stiffness remained largely unchanged, except for the graphite/low-modulus epoxy, which showed reductions in both of approximately 35%. When low-temperature thermal cycling under tensile load was applied, there was a noticeable reduction in modulus and strength in the graphite/low-modulus epoxy and some strength reduction in the S-glass/epoxy.

Daniel, I. M.↗

NASA NTRS1976

Lamination residual stresses in hybrid composites, part 1

An experimental investigation was conducted to study lamination residual stresses for various material and loading parameters. The effects of hybridization on residual stresses and residual properties after thermal cycling under load were determined in angle-ply graphite/Kevlar/epoxy and graphite/S-glass/epoxy laminates. Residual strains in the graphite plies are not appreciably affected by the type and number of hybridizing plies. Computed residual stresses at room temperature in the S-glass plies reach values up to seventy-five percent of the transverse strength of the material. Computed residual stresses in the graphite plies exceed the static strength by approximately ten percent. In the case of Kevlar plies, computed residual stresses far exceed the static strength indicating possible early failure of these plies. Static testing of the hybrids above indicates that failure is governed by the ultimate strain of the graphite plies. In thermally cycled hybrids, in general, residual moduli were somewhat lower and residual strengths were higher than initial values.

Daniel, I. M.↗

NASA NTRS1976

Wave propagation in fiber composite laminates, part 2

An experimental investigation was conducted to determine the wave propagation characteristics, transient strains and residual properties in unidirectional and angle-ply boron/epoxy and graphite/epoxy laminates impacted with silicone rubber projectiles at velocities up to 250 MS-1. The predominant wave is flexural, propagating at different velocities in different directions. In general, measured wave velocities were higher than theoretically predicted values. The amplitude of the in-plane wave is less than ten percent of that of the flexural wave. Peak strains and strain rates in the transverse to the (outer) fiber direction are much higher than those in the direction of the fibers. The dynamics of impact were also studied with high speed photography.

Daniel, I. M.↗

NASA NTRS1976

Strain rate effects on mechanical properties of fiber composites, part 3

An experimental investigation was conducted to determine the strain rate effects in fiber composites. Unidirectional composite specimens of boron/epoxy, graphite/epoxy, S-glass/epoxy and Kevlar/epoxy were tested to determine longitudinal, transverse and intralaminar (in-plane) shear properties. In the Longitudinal direction the Kevlar/epoxy shows a definite increase in both modulus and strength with strain rate. In the transverse direction, a general trend toward higher strength with strain rate is noticed. The intralaminar shear moduli and strengths of boron/epoxy and graphite/epoxy show a definite rise with strain rate.

Daniel, I. M.↗

NASA NTRS1976

Effect of laminate construction on residual stresses in composites

The effects of ply stacking sequence and ply orientation on the magnitude of lamination residual stresses in graphite/polyimide angle-ply laminates was studied. Embedded strain gage techniques were used to measure thermal strains in laminates of different layup, and residual strains were determined by comparing thermal strains in the angle-ply laminates with those of a unidirectional laminate. The ply stacking sequence did not have an effect on the magnitude of residual strains.

Daniel, I. M.↗

NASA NTRS1976

Evaluation of hybrid composite materials in cylindrical specimen geometries

Static and fatigue properties of three composite materials and hybrids were examined. The materials investigated were graphite/epoxy, S-glass/epoxy, PRD-49 (Kevlar 49)/epoxy, and hybrids in angle-ply configurations. A new type of edgeless cylindrical specimen was developed. It is a flattened tube with two flat sides connected by curved sections and it is handled much like the standard flat coupon. Special specimen fabrication, tabbing, and tab region reinforcing techniques were developed. Axial modulus, Poisson's ratio, strength, and ultimate strain were obtained under static loading from flattened tube specimens of nine laminate configurations. In the case of graphite/epoxy the tubular specimens appeared to yield somewhat higher strength and ultimate strain values than flat specimens. Tensile fatigue tests were conducted with all nine types of specimens and S-N curves obtained. Specimens surviving 10 million cycles of tensile loading were subsequently tested statically to failure to determine residual properties.

Liber, T.↗

NASA NTRS1975

Lamination residual stresses in fiber composites

An experimental investigation was conducted to determine the magnitude of lamination residual stresses in angle-ply composites and to evaluate their effects on composite structural integrity. The materials investigated were boron/epoxy, boron/polyimide, graphite/low modulus epoxy, graphite/high modulus epoxy, graphite/polyimide and s-glass/epoxy. These materials were fully characterized. Static properties of laminates were also determined. Experimental techniques using embedded strain gages were developed and used to measure residual strains during curing. The extent of relaxation of lamination residual stresses was investigated. It was concluded that the degree of such relaxation is low. The behavior of angle-ply laminates subjected to thermal cycling, tensile load cycling, and combined thermal cycling with tensile load was investigated. In most cases these cycling programs did not have any measurable influence on residual strength and stiffness of the laminates. In the tensile load cycling tests, the graphite/polyimide shows the highest endurance with 10 million cycle runouts at loads up to 90 percent of the static strength.

Daniel, I. M.↗

NASA NTRS1975

Measurement of residual strains in boron-epoxy and glass-epoxy laminates

Embedded-strain-gage techniques were developed and used for measuring strains in composite angle-ply laminates during curing and thermal cycling. The specimens were 2.54 by 22.9 cm eight-ply boron-epoxy and S-glass-epoxy laminates. Unidirectional specimens were used for control purposes. Strain readings were corrected for the purely thermal output of the gages obtained from an instrument quartz reference specimen. The strains measured during the cooling part of the curing cycle were in agreement with those recorded during subsequent thermal cycling, indicating that residual stresses induced during curing are primarily caused by differential thermal expansions of the various plies. Restraint strains were computed for the 0-deg and 45-deg plies of the angle-ply laminates tested, and the residual stresses obtained using the anisotropic constitutive relations and taking into account the temperature dependence of stiffnesses and strains.

Daniel, I. M.↗