Engineering topics
Cui, Yi
Publications and source records attributed to Cui, Yi.
A New Class of Ionically Conducting Fluorinated Ether Electrolytes with High Electrochemical Stability
Increasing battery energy density is greatly desired for applications such as portable electronics and transportation. However, many next-generation batteries are limited by electrolyte selection because high ionic conductivity and poor electrochemical stability are typically observed in most electrolytes. For example, ether-based electrolytes have high ionic conductivity but are oxidatively unstable above 4 V, which prevents the use of high-voltage cathodes that promise higher energy densities. In contrast, hydrofluoroethers (HFEs) have high oxidative stability but do not dissolve lithium salt. Here, we synthesize a new class of fluorinated ether electrolytes that combine the oxidative stability of HFEs with the ionic conductivity of ethers in a single compound. We show that conductivities of up to 2.7 × 10 –4 S/cm (at 30 °C) can be obtained with oxidative stability up to 5.6 V. The compounds also show higher lithium transference numbers compared to typical ethers. Furthermore, we use nuclear magnetic resonance (NMR) and molecular dynamics (MD) to study their ionic transport behavior and ion solvation environment, respectively. Finally, we demonstrate that this new class of electrolytes can be used with a Ni-rich layered cathode (NMC 811) to obtain over 100 cycles at a C/5 rate. The design of new molecules with high ionic conductivity and high electrochemical stability is a novel approach for the rational design of next-generation batteries.
Electrode roughness dependent electrodeposition of sodium at the nanoscale
Na metal is an attractive anode material for rechargeable Na ion batteries, however, the dendritic growth of Na can cause serious safety issues. Along with modifications of solid-electrolyte interphase (SEI), engineering the electrode has been reported to be effective in suppressing Na dendritic growth, likely by reducing localized current density accumulation. However, fundamental understanding of Na growth at the nanoscale is still limited. Here, we report an in-situ study of Na electrodeposition in electrochemical liquid cells with the electrodes in different surface roughness, e.g., flat or sharp curvature. Real time observation using transmission electron microscopy (TEM) reveals the Na electrodeposition with remarkable details. Relatively large Na grains (in the micrometer scale) are achieved on the flat electrode surface. The local SEI thickness variations impact the growth rate, thus the morphology of individual grains. In contrast, small Na grains (in tens of nanometers) grow explosively on the electrode at the point with sharp curvature. The newly formed Na grains preferentially deposit at the base of existing grains close to the electrode. Further studies using continuum-based computational modeling suggest that the growth mode of an alkali metal (e.g. Na) is strongly influenced by the transport properties of SEI. Our direct observation of Na deposition in combination with the theoretical modeling provides insights for comprehensive understanding of electrode roughness and SEI effects on Na electrochemical deposition.
Resolving Nanoscopic and Mesoscopic Heterogeneity of Fluorinated Species in Battery Solid-Electrolyte Interphases by Cryogenic Electron Microscopy
The stability of lithium batteries is tied to the physicochemical properties of the solid-electrolyte interphase (SEI). Owing to the difficulty in characterizing this sensitive interphase, the nanoscale distribution of SEI components is poorly understood. Here, we use cryogenic scanning transmission electron microscopy (cryo-STEM) to map the spatial distribution of SEI components across the metallic Li anode. We reveal that LiF, an SEI component widely believed to play an important role in battery passivation, is absent within the compact SEI film (~15 nm); instead, LiF particles (100–400 nm) precipitate across the electrode surface. We term this larger length scale as the indirect SEI regime. On the basis of these observations, we conclude that LiF cannot be a dominant contribution to anode passivation nor does it influence Li+ transport across the compact SEI film. We refine the traditional SEI structure derived from ensemble-averaged characterizations and nuance the role of SEI components on battery performance.
A novel battery scheme: Coupling nanostructured phosphorus anodes with lithium sulfide cathodes
Lithium-ion batteries are approaching their theoretical limit and can no longer keep up with the increasing demands of human society. Lithium-sulfur batteries, with a high theoretical specific energy, are promising candidates for next generation energy storage. However, the use of Li metal in Li-S batteries compromises both safety and performance, enabling dendrite formation and causing fast capacity degradation. Previous studies have probed alternative battery systems to replace the metallic Li in Li-S system, such as a Si/Li2S couple, with limited success in performance. Recently, there is a focus on red P as a favorable anode material to host Li. In this work, we establish a novel battery scheme by utilizing a P/C nanocomposite anode and pairing it with a Li 2 S coated carbon nanofiber cathode. We find that red P anode can be compatible in ether-based electrolyte systems and can be successfully coupled to a Li 2 S cathode. Our proof of concept full-cell displays remarkable specific capacity, rate and cycling performances. We expect our work will provide a useful alternative system and valuable insight in the quest for next generation energy storage devices.
High-purity electrolytic lithium obtained from low-purity sources using solid electrolyte
Lithium (Li) is an important resource for the sustainability of socioeconomic systems given its wide use in various industrial applications. The industrial production of Li metals relies on the electrolysis of a mixture consisting of high-purity lithium chloride (LiCl) and potassium chloride. However, the purification of LiCl is expensive and unsustainable, requiring a substantial amount of energy and the use of noxious chemical reagents, so that producing high-purity Li efficiently and sustainably is a challenge. In this paper we report a new method of producing high-purity electrolytic Li from low-purity LiCl using solid-state electrolyte. Taking advantage of the high Li-ion selectivity of the solid electrolyte, we directly obtained high-purity metallic Li through the electrolysis of low-purity LiCl. Our new method provides two important advantages over conventional methods: (1) the cost of producing high-purity Li is reduced by using low-purity LiCl from low-grade brine, and the simpler purification process reduces the use of energy and chemical reagents; and (2) the operating temperature of the electrolytic process decreases from 400 °C to 240 °C, leading to an additional reduction in energy use.
Silica accelerates the selective hydrogenation of CO 2 to methanol on cobalt catalysts
The reaction pathways on supported catalysts can be tuned by optimizing the catalyst structures, which helps the development of efficient catalysts. Such design is particularly desired for CO 2 hydrogenation, which is characterized by complex pathways and multiple products. Here, we report an investigation of supported cobalt, which is known for its hydrocarbon production and ability to turn into a selective catalyst for methanol synthesis in CO 2 hydrogenation which exhibits good activity and stability. The crucial technique is to use the silica, acting as a support and ligand, to modify the cobalt species via Co-O-SiOn linkages, which favor the reactivity of spectroscopically identified *CH 3 O intermediates, that more readily undergo hydrogenation to methanol than the C-O dissociation associated with hydrocarbon formation. Cobalt catalysts in this class offer appealing opportunities for optimizing selectivity in CO 2 hydrogenation and producing high-grade methanol. By identifying this function of silica, we provide support for rationally controlling these reaction pathways.
Encapsulated sulfur cathodes for rechargeable lithium batteries
A method of forming a sulfur-based cathode material includes: 1) providing a sulfur-based nanostructure; 2) coating the nanostructure with an encapsulating material to form a shell surrounding the nanostructure; and 3) removing a portion of the nanostructure through the shell to form a void within the shell, with a remaining portion of the nanostructure disposed within the shell.
Mechanical rolling formation of interpenetrated lithium metal/lithium tin alloy foil for ultrahigh-rate battery anode
To achieve good rate capability of lithium metal anodes for high-energy-density batteries, one fundamental challenge is the slow lithium diffusion at the interface. Here we report an interpenetrated, three-dimensional lithium metal/lithium tin alloy nanocomposite foil realized by a simple calendering and folding process of lithium and tin foils, and spontaneous alloying reactions. The strong affinity between the metallic lithium and lithium tin alloy as mixed electronic and ionic conducting networks, and their abundant interfaces enable ultrafast charger diffusion across the entire electrode. Furthermore, we demonstrate that a lithium/lithium tin alloy foil electrode sustains stable lithium stripping/plating under 30 mA cm -2 and 5 mAh cm -2 with a very low overpotential of 20 mV for 200 cycles in a commercial carbonate electrolyte. Cycled under 6 C (6.6 mA cm -2 ), a 1.0 mAh cm -2 LiNi 0.6 Co 0.2 Mn 0.2 O 2 electrode maintains a substantial 74% of its capacity by pairing with such anode.
A Fireproof, Lightweight, Polymer–Polymer Solid-State Electrolyte for Safe Lithium Batteries
Safety issues in lithium-ion batteries have raised serious concerns due to their ubiquitous utilization and close contact with the human body. Replacing flammable liquid electrolytes, solid-state electrolytes (SSEs) is thought to address this issue as well as provide unmatched energy densities in Li-based batteries. However, among the most intensively studied SSEs, polymeric solid electrolyte and polymer/ceramic composites are usually flammable, leaving the safety issue unattended. Here, we report the first design of a fireproof, ultralightweight polymer–polymer SSE. The SSE is composed of a porous mechanic enforcer (polyimide, PI), a fire-retardant additive (decabromodiphenyl ethane, DBDPE), and a ionic conductive polymer electrolyte (poly(ethylene oxide)/lithium bis(trifluoromethanesulfonyl)imide). The whole SSE is made from organic materials, with a thin, tunable thickness (10–25 μm), which endorse the energy density comparable to conventional separator/liquid electrolytes. The PI/DBDPE film is thermally stable, nonflammable, and mechanically strong, preventing Li–Li symmetrical cells from short-circuiting after more than 300 h of cycling. LiFePO 4 /Li half cells with our SSE show a high rate performance (131 mAh g –1 at 1 C) as well as cycling performance (300 cycles at C/2 rate) at 60 °C. Most intriguingly, pouch cells made with our polymer–polymer SSE still functioned well even under flame abuse tests.
Comprehensive proteomics analysis of stressed human islets identifies GDF15 as a target for type 1 diabetes intervention
Type 1 diabetes results from the progressive loss of beta cells, a process propagated by pro-inflammatory cytokine signaling that disrupts the balance between the expression of pro- and anti-apoptotic proteins. To identify such proteins, we performed comprehensive proteomics of human pancreatic islets treated with interleukin-1ß and interferon-?, leading to the identification of 11,325 proteins, of which 387 were significantly regulated by treatment. We then tested the function of growth/differentiation factor 15 (GDF15), which was repressed by the cytokine treatment. We found that GDF15 translation was blocked during inflammation, while the addition of exogenous GDF15 inhibited interleukin-1ß/interferon-?-induced apoptosis of human islets and a human beta-cell line. Furthermore, administration of GDF15 significantly decreased insulitis in NOD mice. Our approach provides a unique resource for the identification of the human islet proteins regulated by cytokines and was effective in discovering a potential target for type 1 diabetes therapy.
Membrane-Free Zn/MnO 2 Flow Battery for Large-Scale Energy Storage
The traditional Zn/MnO 2 battery has attracted great interest due to its low cost, high safety, high output voltage, and environmental friendliness. However, it remains a big challenge to achieve long-term stability, mainly owing to the poor reversibility of the cathode reaction. Different from previous studies where the cathode redox reaction of MnO 2 /MnOOH is in solid state with limited reversibility, in this work a new aqueous rechargeable Zn/MnO 2 flow battery is constructed with dissolution–precipitation reactions in both cathodes (Mn 2+ /MnO 2 ) and anodes (Zn 2+ /Zn), which allow mixing of anolyte and catholyte into only one electrolyte and remove the requirement for an ion selective membrane for cost reduction. Impressively, this new battery exhibits a high discharge voltage of ≈1.78 V, good rate capability (10C discharge), and excellent cycling stability (1000 cycles without decay) at the areal capacity ranging from 0.5 to 2 mAh cm -2 . More importantly, this battery can be readily enlarged to a bench scale flow cell of 1.2 Ah with good capacity retention of 89.7% at the 500th cycle, displaying great potential for large-scale energy storage.
A Single‐Ion Conducting Borate Network Polymer as a Viable Quasi‐Solid Electrolyte for Lithium Metal Batteries
Abstract Lithium‐ion batteries have remained a state‐of‐the‐art electrochemical energy storage technology for decades now, but their energy densities are limited by electrode materials and conventional liquid electrolytes can pose significant safety concerns. Lithium metal batteries featuring Li metal anodes, solid polymer electrolytes, and high‐voltage cathodes represent promising candidates for next‐generation devices exhibiting improved power and safety, but such solid polymer electrolytes generally do not exhibit the required excellent electrochemical properties and thermal stability in tandem. Here, an interpenetrating network polymer with weakly coordinating anion nodes that functions as a high‐performing single‐ion conducting electrolyte in the presence of minimal plasticizer, with a wide electrochemical stability window, a high room‐temperature conductivity of 1.5 × 10 −4 S cm −1 , and exceptional selectivity for Li‐ion conduction ( t Li+ = 0.95) is reported. Importantly, this material is also flame retardant and highly stable in contact with lithium metal. Significantly, a lithium metal battery prototype containing this quasi‐solid electrolyte is shown to outperform a conventional battery featuring a polymer electrolyte.
Electrochemical generation of liquid and solid sulfur on two-dimensional layered materials with distinct areal capacities
It has recently been shown that sulfur, a solid material in its elementary form S8, can stay in a supercooled state as liquid sulfur in an electrochemical cell. We establish that this newly discovered state could have implications for lithium–sulfur batteries. Here, through in situ studies of electrochemical sulfur generation, we show that liquid (supercooled) and solid elementary sulfur possess very different areal capacities over the same charging period. To control the physical state of sulfur, we studied its growth on two-dimensional layered materials. We found that on the basal plane, only liquid sulfur accumulates; by contrast, at the edge sites, liquid sulfur accumulates if the thickness of the two-dimensional material is small, whereas solid sulfur nucleates if the thickness is large (tens of nanometres). Correlating the sulfur states with their respective areal capacities, as well as controlling the growth of sulfur on two-dimensional materials, could provide insights for the design of future lithium–sulfur batteries.
Molybdenum disulfide and related materials for water treatment
Catalytic water treatment is provided using an active material driven with an optical and/or electrical excitation. The active material is MoS2, MoSe2, WS2, WSe2, MoxW1-xS2, MoxW1-xSe2, MoSySe2-y, WSySe2-y, or MoxW1-xSySe2-y; wherein 0 < x < 1 and 0 < y < 2. The active material is configured as one or more layered nanostructures having exposed layer edges. A metal catalyst is disposed on the active material. The combined structure of active material and metal catalyst is disposed in the water to be treated. The excitation is provided to the active material to generate one or more reactive oxygen species by dissociation of water, wherein the reactive oxygen species provide water treatment.
Efficient synthesis of high-sulfur-content cathodes for high-performance Li–S batteries based on solvothermal polysulfide chemistry
A novel solvothermal polysulfide (PS) chemistry enables a facile and highly efficient process for synthesizing sulfur-carbon (S–C) composite powders containing up to 90 wt% S for high-performance Li–S batteries. Molecular dynamics calculations and experimental analyses reveal the formation of PSs upon dissolution of elemental S in N-methyl-2-pyrrolidone (NMP) at elevated temperatures and efficient infiltration of the PSs into the carbon host driven by the strong coupling with the C surfaces. The coupling enables extensive contact between S and C in the composite, leading to promising electrochemical properties for Li–S battery applications. In the power-type configuration, the composite cathodes having medium-to-high S contents (55 and 75%) demonstrate stable capacity at high current densities up to 100C (1C = 1670 mA g -1 -S) and no capacity fade up to 1000 cycles at 2C. In the energy-type configuration, a high-S-content and high-loading (90%-S, 4.2 mAh cm -2 ) cathode shows a specific capacity of 1440 mAh g -1 (86% S utilization) and 90% capacity retention after 300 cycles. This synthesis method enables significant advancement in realizing large-scale applications of Li–S batteries.
Theoretical Calculation Guided Design of Single-Atom Catalysts toward Fast Kinetic and Long-Life Li–S Batteries
Lithium–sulfur (Li–S) batteries are enticing next-generation energy storage technologies due to their high theoretical energy density, environmental friendliness, and low cost. Yet, low conductivity of sulfur species, dissolution of polysulfides, poor conversion from sulfur reduction, and lithium sulfide (Li 2 S) oxidation reactions during discharge–charge processes hinder their practical applications. Herein, under the guidance of density functional theory calculations, we have successfully synthesized large-scale single atom vanadium catalysts seeded on graphene to achieve high sulfur content (80 wt % sulfur), fast kinetic (a capacity of 645 mAh g –1 at 3 C rate), and long-life Li–S batteries. Both forward (sulfur reduction) and reverse reactions (Li 2 S oxidation) are significantly improved by the single atom catalysts. This finding is confirmed by experimental results and consistent with theoretical calculations. The ability of single metal atoms to effectively trap the dissolved lithium polysulfides (LiPSs) and catalytically convert the LiPSs/Li 2 S during cycling significantly improved sulfur utilization, rate capability, and cycling life. Our work demonstrates an efficient design pathway for single atom catalysts and offers solutions for the development of high energy/power density Li–S batteries.
High-temperature, spectrally-selective, scalable, and flexible thin-film Si absorber and emitter
Solar thermal technologies have great potential to provide low-cost storage for solar energy. However, their efficiencies are limited by a lack of scalable, mechanically flexible, durable, yet highly-efficient spectrally-selective solar absorbers suitable for high temperatures at low solar concentrations. Here, we overcome these challenges by fabricating a scalable free-standing spectrally-selective thin-film Si absorber and emitter (SSTFS) composite. Its high-temperature emittance shows strong spectral selectivity, even at 595 °C. Thermal stability is proven by measuring optical properties before and after thermal cycling equivalent to one day of concentrated sunlight. Despite the use of crystalline Si, the fabricated SSTFS composite exhibits exceptional mechanical flexibility to cover most surface geometries. The SSTFS composite demonstrates the potential of high-temperature, efficient and flexible solar absorbers and thermal emitters to advance renewable solar energy with storage.