Engineering topics

Choi, Sung R.

Publications and source records attributed to Choi, Sung R..

At least 91 records · Page 5

NASA NTRS1996

"Inert" Strengths of Silicon Nitride Ceramics at Elevated Temperatures

An attempt to determine high temperature "inert" strengths of several silicon nitride ceramics was made by using dynamic fatigue testing at the very high stressing rate of 2 x 106 MPa/min. The fatigue strengths of all the silicon nitride materials exhibited a well-defined convergence to the corresponding room-temperature inert strengths as stressing rate was increased. The result showed that the high temperature Inert" strength of a ceramic material can be obtained by using sufficiently high stressing rates (greater or = 2 x 10(exp 6) MPa/min) at which fatigue strength converges to a specific value. The specific value can be close to the room-temperature strength of the material.

Choi, Sung R.↗

NASA NTRS1996

Free-Roller Versus Fixed-Roller Fixtures in Flexure Testing of Advanced Ceramic Materials

The error associated with strength measurements made with fixed-roller and V-grooved roller figures was studied with a variety of roller and figure material combinations. Both the fixed-roller and the V-grooved fixtures yielded an error in stress of about 4 to 7%. They also exhibited an appreciable amount of load strain hysteresis. Dynamic fatigue testing of 96 wt.% alumina verified the error: the fatigue strength was overestimated by 7 to 9% for the fixed roller configuration. The source of error is exclusively attributed to friction between the rollers and the specimen surface, as verified by previous investigators.

Salem, Jonathan A.↗

NASA NTRS1995

Reliability Analysis of Uniaxially Ground Brittle Materials

The fast fracture strength distribution of uniaxially ground, alpha silicon carbide was investigated as a function of grinding angle relative to the principal stress direction in flexure. Both as-ground and ground/annealed surfaces were investigated. The resulting flexural strength distributions were used to verify reliability models and predict the strength distribution of larger plate specimens tested in biaxial flexure. Complete fractography was done on the specimens. Failures occurred from agglomerates, machining cracks, or hybrid flaws that consisted of a machining crack located at a processing agglomerate. Annealing eliminated failures due to machining damage. Reliability analyses were performed using two and three parameter Weibull and Batdorf methodologies. The Weibull size effect was demonstrated for machining flaws. Mixed mode reliability models reasonably predicted the strength distributions of uniaxial flexure and biaxial plate specimens.

Salem, Jonathan A.↗

NASA NTRS1995

Effect of Preloading on Fatigue Strength in Dynamic Fatigue Testing of Ceramic Materials at Elevated Temperatures

Previously derived solutions of fatigue strength as a function of preloading were verified by applying preloads to elevated temperature dynamic fatigue tests of 96 wt% alumina at 1000 C and NC 132 silicon nitride at 1100 C. The technique was found very useful in identification and control of the governing failure mechanism when multiple failure mechanisms, such as slow crack growth, creep and oxidation occurred simultaneously at elevated temperatures.

Choi, Sung R.↗

NASA NTRS1995

High Temperature Slow Crack Growth of Si3N4 Specimens Subjected to Uniaxial and Biaxial Dynamic Fatigue Loading Conditions

The slow crack growth of a hot-pressed silicon nitride was determined at 1300 C in air using dynamic fatigue testing under both uniaxial and biaxial stress states. Good agreement in fatigue parameter exists between the data obtained from uniaxial and biaxial loading conditions. A reasonable prediction of dynamic fatigue from one stress state to another was made using the recently developed CARES/LIFE computer code.

Choi, Sung R.↗

NASA NTRS1994

Thermal Shock Behavior of Silicon Nitride Flexure Beam Specimens with Indentation Cracks

The experimental results of thermal shock testing of silicon nitride flexure beam specimens containing indentation cracks are presented. The thermal stress induced by water quenching is much greater in the transverse direction than in the longitudinal direction, resulting in an insensitivity of residual bend strength to temperature differences up to 580 C. This result indicates that a flexure beam configuration is not an appropriate geometry for thermal shock testing when thermal shock behavior is to be evaluated from residual bend strength data.

Choi, Sung R.↗

NASA NTRS1994

Elevated Temperature Slow Crack Growth of Silicon Nitride Under Dynamic, Static and Cyclic Flexural Loading

The slow crack growth parameters of a hot-pressed silicon nitride were determined at 1200 and 1300 C in air by statically, dynamically and cyclicly loading bend specimens. The fatigue parameters were estimated using the recently developed CARES/Life computer code. Good agreement exists between the flexural results. However, fatigue susceptibility under static uniaxial tensile loading, reported elsewhere, was greater than in flexure. Cyclic flexural loading resulted in the lowest apparent flexural fatigue susceptibility.

Choi, Sung R.↗

NASA NTRS1993

Processing and testing of high toughness silicon nitride ceramics

High toughness silicon nitride ceramics were processed with the addition of small quantities of beta-Si3N4 whiskers in a commercially available alpha-Si3N4 powder. These whiskers grew preferentially during sintering resulting in large, elongated beta-grains, which acted to toughen the matrix by crack deflection and grain pullout. The fracture toughness of these samples seeded with beta-Si3N4 whiskers ranged from 8.7 to 9.5 MPa m(exp 0.5) depending on the sintering additives.

Tikare, Veena↗

NASA NTRS1993

Combined mode I and mode II fracture of monolithic ceramics

The mode I, mode II, and combined mode I-mode II fracture behaviors of a coarse-grained silicon nitride, a fine-grained silicon nitride, and an alumina were investigated. These ceramics were fractured from two types of fracture initiating flaws: small surface flaws and large single edge precracks. The small surface flaws were introduced by Knoop indentation in flexural samples at various angles to the tensile stress direction and fractured in four-point bending. The samples with large precracks were fractured in the asymmetric four-point-bend geometry. The mixed-mode fracture toughness values obtained from the two flaw configurations were in good agreement with each other. All three ceramics displayed very similar mixed-mode fracture behavior, although their microstructures were not similar. Comparison of experimental data to mixed-mode fracture theories revealed that the minimum strain energy density theory best described the mixed-mode fracture behavior of all three ceramics.

Tikare, Veena↗

NASA NTRS1993

Effect of environment on fracture toughness of 96 wt pct alumina

An effort is made to deepen understanding of environmental effects on the fracture toughness of an alumina composition that contains a residual glassy phase, by ascertaining the fracture toughness under atmospheric conditions in such varied environments as air distilled water, silicone oil, and liquid nitrogen. Fracture toughness was determined via the single-edge-precracked beam technique. Weibull strength parameters are compared for polished specimens tested both in air and silicone environments.

Choi, Sung R.↗

NASA NTRS1992

Indentation flaw formation and strength response of silicon nitride ceramics at low indentation loads

The configuration and the strength response of indentation flaws in silicon nitrides are described as a function of indentation loads primarily near the threshold level. Test materials under consideration include 30 vol percent SiC whisker-reinforced composite silicon nitride and similar monolithic silicon nitride. The results of strength testing show that, at indentation loads less than or equal to 1.96, a number of the specimens fail from the intrinsic flaws of the materials rather than from the indent sites, causing a distinct trend to reach a plateau, at a level corresponding to the as-received strength of the material. The ratio of the mirror constant to the fracture toughness for the composite and monolithic materials is found to be 1.44 and 1.51, respectively.

Choi, Sung R.↗

NASA NTRS1992

Analysis of precracking parameters and fracture toughness for ceramic single-edge-precracked-beam specimens

The single-edge-precracked-beam (SEPB) method involves creation of a straight-through crack from an indentation crack. The straight-through crack is developed by applying a controlled bending load to a specimen via a precracking fixture. The fixture induces the following sequence: (1) stable growth of the indentation crack; (2) pop-in; and finally, (3) arrest-thereby forming a straight-through precrack. The effects of indentation load on precracking load as well as precrack size were studied for experimental variables such as specimen width, fixture span, and material. Finite element analysis was used to obtain the stress distribution and stress intensity factor, thus providing a quantitative prediction of the precracking load and precrack size for silicon nitride, alumina, silicon cabide, and two SiC whisker-reinforced silicon nitrides. Fracture toughness values obtained from the SEPB method were compared with those obtained from other methods.

Choi, Sung R.↗

NASA NTRS1992

Estimation of crack closure stresses for in situ toughened silicon nitride with 8 wt pct scandia

An 8-wt pct-scandia silicon nitride with an elongated grain structure was fabricated. The material exhibited high fracture toughness and a rising R-curve as measured by the indentation strength technique. The 'toughening' exponent m was found to be m about 0.1. The high fracture toughness and R-curve behavior was attributed mainly to bridging of the crack faces by the elongated grains. The crack closure (bridging) stress distribution in the wake region of the crack tip was estimated as a function of crack size from the R-curve data, with an arbitrarily assumed distribution function.

Choi, Sung R.↗

NASA NTRS1992

Analysis of precracking parameters for ceramic single-edge-precracked-beam specimens

The single-edge-precracked-beam (SEPB) method involves creation of a straight-through crack from an indentation crack. The straight-through crack is developed by applying a controlled bending load to a specimen via a precracking fixture. The fixture induces the following sequence: (1) stable growth of the indentation crack; (2) pop-in; and finally, (3) arrest - thereby forming a straight-through precrack. The effects of indentation load on precracking load as well as precrack size were studied for experimental variables such as specimen width, fixture span, and material. Finite element analysis was used to obtain the stress distribution and stress intensity factor, thus providing a quantitative prediction of the precracking load and precrack size for silicon nitride, alumina, silicon carbide, and two SiC whisker-reinforced silicon nitrides. Fracture toughness values obtained from the SEPB method were compared with those obtained from other methods.

Choi, Sung R.↗

NASA NTRS1991

Elevated temperature mechanical behavior of monolithic and SiC whisker-reinforced silicon nitrides

The mechanical behavior of a 30 volume percent SiC whisker reinforced silicon nitride and a similar monolithic silicon nitride were measured at several temperatures. Measurements included strength, fracture toughness, crack growth resistance, dynamic fatigue susceptibility, post oxidation strength, and creep rate. Strength controlling defects were determined with fractographic analysis. The addition of SiC whiskers to silicon nitride did not substantially improve the strength, fracture toughness, or crack growth resistance. However, the fatigue resistance, post oxidation strength, and creep resistance were diminished by the whisker addition.

Salem, Jonathan A.↗

NASA NTRS1991

Crack healing in silicon nitride due to oxidation

The crack healing behavior of a commercial, MgO-containing, hot pressed Si3N4 was studied as a function of temperature in oxidizing and inert annealing environments. Crack healing occurred at a temperature 800 C or higher due to oxidation regardless of crack size, which ranged from 100 microns (indentation crack) to 1.7 mm (SEPB precrack). The resulting strength and apparent fracture toughness increased at crack healing temperature by 100 percent and 300 percent, respectively. The oxide layer present in the crack plane was found to be highly fatigue resistant, indicating that the oxide is not solely silicate glass, but a mixture of glass, enstatite, and/or cristobalite that was insensitive to fatigue in a room temperature water environment.

Choi, Sung R.↗

NASA NTRS1991

Influence of the Si3N4 microstructure on its R-curve and fatigue behavior

The R-curve and fatigue behavior of a silicon nitride with large, highly elongated grains were compared to those of a silicon nitride with smaller, more equiaxed grains. The former was found to have higher toughness and a slightly rising R-curve which enhanced fatigue resistance, while the latter had constant toughness with crack length. The R-curve was attributed to crack deflection and grain pull-out. The microstructure did not influence the dynamic fatigue properties of the two ceramics, as both had good resistance to dynamic fatigue. The cyclic fatigue resistance of the large-grained Si3N4, however, was surprisingly low.

Tikare, Veena↗

NASA NTRS1991

Dynamic fatigue property of silicon carbide whisker-reinforced silicon nitride

The dynamic fatigue behavior of 30 vol pct SiC whisker-reinforced silicon nitride was determined in flexure as a function of temperature from 1100 to 1300 C in an air environment. The fatigue susceptibility parameter n decreased from 88.1 to 20.1 with increasing temperature from 1100 to 1300 C. A transition in the dynamic fatigue curve occurred at a lowest stressing rate of 2 MPa/min at a temperature of 1300 C, resulting in a considerably lower value of n = 5.8. This transition was primarily due to creep that was enhanced by a combination of high temperature and very slow deformation rate. The fatigue resistance of natural flaws at 1100 C was found to be greater than that of artificial flaws produced by indentation.

Choi, Sung R.↗