Engineering Papers⌕ Search

Engineering topics

Chen, J. C.

Publications and source records attributed to Chen, J. C..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A comparison of measured spacecraft modal damping values

The prediction and the measurement of modal damping values of spacecrafts for use in the determination of design loads were summarized. Realistic transient forcing functions were used. The solution of complex eigenvalue response solutions resulting from modal synthesis of subsystems in which each subsystem is assigned modal damping values is discussed. Damping data on both the Voyager and the Galileo spacecrafts using up to eight different types of techniques to analyze modal data are presented. It is concluded that it is difficult to estimate the true damping of a structure and the measured damping values which are dependent on the analysis method of the data.

Wada, B. K.↗
NASA NTRS1984

Application of multiple input random and polyreference analysis techniques to the Galileo spacecraft modal test

An experimental modal analysis of the Galileo spacecraft was required to verify a finite element model used in loads analysis. Multiple input random and polyreference analysis techniques were applied in this program to demonstrate their effectiveness in determining the modal characteristics of a complex space structure. The methods were successful in determining an accurate set of modal data from two days of data acquisition. A complete set of results was available within 24 hours of test completion. Final analysis shows the modes from the multiple input random tests to be more complete and orthogonal than those obtained from classical sine dwell methods.

Chen, J. C.↗
NASA NTRS1983

Methods for Estimating Payload/Vehicle Design Loads

Several methods compared with respect to accuracy, design conservatism, and cost. Objective of survey: reduce time and expense of load calculation by selecting approximate method having sufficient accuracy for problem at hand. Methods generally applicable to dynamic load analysis in other aerospace and other vehicle/payload systems.

Chen, J. C.↗
NASA NTRS1983

Modal test and analysis correlation

Modal testing plays a significant role in experimentally measuring the modal parameters used directly for response analysis of spacecraft or indirectly to update a mathematical model for use in response analysis. Developments in modal testing and correlation of results to analytical models are discussed. Several procedures to semi-automate correlation of resonant frequency and mode shape test data to the model have been shown to be valid for hypothetical problems but have not been successful in practice. Improving the correlation of frequencies and mode shapes does not necessarily improve the correlation of modal force coefficients. The paper discusses other parameters, such as kinetic energy and strain energy, which may be more significant in the correlation process. Because the most demanding requirement of a modal test is in determining dynamic loads, the authors asssume that objective, minimally discussing theoretical developments, summarizing their results, and giving sample data.

Wada, B. K.↗
NASA NTRS1981

A survey of load methodologies for shuttle orbiter payloads

Loads methods currently being used to design planetary spacecraft to be launched on the shuttle orbiter are summarized. Experiences gained from expendable launch vehicle payloads are used to develop methodologies for the space shuttle orbiter payloads. The objectives for the development of a new methodology for the shuttle payloads are to reduce the cost and schedule for the payload load analysis by decoupling the payload analysis from the launch vehicle to the maximum extent possible. Methods are described for payload member load estimation or obtaining upper bounds for dynamic loads, as well as load prediction or calculating actual transient member load time histories.

Chen, J. C.↗
NASA NTRS1980

A survey of load methodologies for shuttle orbiter payloads

Loads methods currently being used to design shuttle orbiter payloads are summarized. Methods used for the design of payloads launched by expendable launch vehicles are described in historical perspective. Experiences gained from expendable launch vehicle payloads are used to develop methodologies for the space shuttle orbiter payloads. The objectives for the development of a new methodology for the shuttle payloads are to reduce the cost and schedule for the payload load analysis by decoupling the payload analysis from the launch vehicle to the maximum extent possible. Methods are described for payload member load estimation or obtaining upper bounds for dynamic loads, as well as load prediction or calculating actual transient member load time histories.

Chen, J. C.↗
NASA NTRS1980

Recovered transient load analysis for payload structural systems

A recovered transient analysis technique is proposed wherein the results of a previous launch vehicle/payload system can be used to obtain the information on a new payload structure to be launched by an identical launch vehicle. The advantage of the proposed method is that the complete analysis can be performed within the payload organization with the same accuracy as that of a full scale, multiorganizational loads analysis. Also, the flight measured interface accelerations can be used as the forcing functions for more realistic representations of the dynamic environments.

Chen, J. C.↗
NASA NTRS1980

Spacecraft loads methodology - Transient vs. shock spectra method

The methodology for the establishment of spacecraft loads is strongly influenced by project constraints which include the cost, schedule and allowable weight. The most rigorous approach is the transient loads analysis which requires a composite mathematical model of the spacecraft and launch vehicle. The structural member loads for the entire composite structure are computed by applying the forcing functions, which represent various dynamic environments during the mission, to the composite model. Although this method ideally leads to a lightweight design, it is costly and time consuming due to complex interfaces involving many organizations. To reduce complexity and cost a shock spectra method has been used to design spacecraft structures. This method utilizes envelopes of shock spectra of launch vehicle accelerations obtained from analysis and/or flight measurements. Since only limited information on the launch vehicle model is involved in this process the design loads iteration cycle can be rapidly performed within the payload organization. In the present paper, these two methods will be evaluated by comparing the loads for several spacecraft. Flight measured loads will also be used in the evaluation.

Chen, J. C.↗
NASA NTRS1979

Voyager design and flight loads comparison

Estimates of flight loads for Voyager 1 and Voyager 2 are summarized. These member loads are obtained by using the measured flight accelerations at the launch vehicle/spacecraft interface as forcing functions for the Voyager mathematical model. The flight loads are compared to the Voyager design loads obtained from the shock spectra/impedance method and to the loads obtained using space vehicle transient loads analysis. Finally, based on these data, an assessment of the shock spectra/impedance loads method used for Voyager is presented.

Chen, J. C.↗
NASA NTRS1979

Matrix perturbation for analytical model improvement

A matrix perturbation method is proposed to calculate the Jacobian matrix and to compute the new eigendata for the parameter estimation procedure. The advantages of the method are the applicability to large complex structures without knowing the analytical expressions for the mass and stiffness matrices, and a cost effective approach for the re-computation of the eigendata. This method also allows the use of other measurements such as modal forces, kinetic energy distribution, and strain energy distributions in the estimation procedure. A realistic sample problem is presented to demonstrate the effectiveness of the proposed method.

Chen, J. C.↗
NASA NTRS1978

Summary of Voyager Design and Flight Loads

Estimates of flight loads for Voyager 1 and Voyager 2 are summarized and compared to the Voyager design loads obtained from the shock spectra/impedance method and to the loads obtained using space vehicle transient loads analysis. These estimates were obtained by using the measured flight accelerations at the launch vehicle/spacecraft interface as forcing functions for the Voyager mathematical model. Based on these data, an assessment of the shock spectra/impedance loads method used for Voyager is presented. The following conclusions were reached: (1) the shock spectra approach provided reasonable conservative design loads for Voyager, (2) care has to be executed to insure that all critical events are accounted for in constructing shock spectra envelopes, (3) the selection of critical events is not always obvious, especially for those flight events wherein the spacecraft dynamic characteristics are important, and (4) the success of the method is strongly dependent on the analysts' experience and judgement.

Chen, J. C.↗
NASA NTRS1978

Estimation of payload loads using rigid body interface accelerations

In the design/analysis process of a payload structural system, the accelerations at the payload/launch vehicle interface obtained from a system analysis using a rigid payload are often used as the input forcing function to the elastic payload to obtain structural design loads. Such an analysis is at best an approximation since the elastic coupling effects are neglected. This paper develops a method wherein the launch vehicle/rigid payload interface accelerations are modified to account for the payload elasticity. The advantage of the proposed method, which is exact to the extent that the physical system can be described by a truncated set of generalized coordinates, is that the complete design/analysis process can be performed within the organization responsible for the payload design. The method requires the updating of the system normal modes to account for payload changes, but does not require a complete transient solution using the composite system model. An application to a real complex structure, the Viking Spacecraft System, is given.

Chen, J. C.↗
NASA NTRS1977

Finite-element solutions for geothermal systems

Vector potential and scalar potential are used to formulate the governing equations for a single-component and single-phase geothermal system. By assuming an initial temperature field, the fluid velocity can be determined which, in turn, is used to calculate the convective heat transfer. The energy equation is then solved by considering convected heat as a distributed source. Using the resulting temperature to compute new source terms, the final results are obtained by iterations of the procedure. Finite-element methods are proposed for modeling of realistic geothermal systems; the advantages of such methods are discussed. The developed methodology is then applied to a sample problem. Favorable agreement is obtained by comparisons with a previous study.

Chen, J. C.↗
NASA NTRS1977

On the launch vehicle payload interface response

A method has been developed by which an estimate of the launch vehicle/payload interface response is derived from the interface responses obtained from missions with the identical launch vehicle but different payloads. This method requires knowledge of the launch vehicle eigenvalues, interface modal displacements, and the dynamic characteristics of the payloads. No other launch vehicle information is required. The organization responsible for the payload is able to perform loads and responses analysis resulting from a payload change without interfacing with the launch vehicle organization.

Chen, J. C.↗
NASA NTRS1976

Matrix perturbation for structural dynamic analysis

The objective of the effort was to investigate methodologies to reduce the cost of evaluating changes in dynamic loads when small modifications are made in the structure. A matrix perturbation technique has been developed to calculate the dynamic responses of a structural system that has been modified from the original design. The calculation is based on the results of the original design and the assumption that the structural modification is small. The advantage of the method is an update of the dynamic response due to design changes without performing an entire analysis. This procedure can be used in a design load analysis cycle in which the structural design is subject to frequent changes. A sample problem is given to demonstrate the validity of the technique.

Chen, J. C.↗
NASA NTRS1975

Nonlinear vibration of cylindrical shells

The large amplitude vibration of a thin-walled cylindrical shell is analyzed. A perturbation method is used to solve the steady-state forced vibration problem. The simply-supported boundary conditions and the circumferential periodicity condition are satisfied. The resulting solution indicates that in addition to the fundamental mode, the response contains asymmetric modes as well as axisymmetric modes with the frequency twice that of the fundamental mode. Vibrations involving a single driven mode response are investigated. The results indicate that the nonlinearity is either softening or hardening depending on the mode. The vibrations involving both a driven mode and a companion mode are also investigated. An experimental investigation is conducted, and the results are in qualitative agreement with the theory. 'Nonstationary' response is detected at some frequencies for large amplitude response in which the amplitude drifts from one value to another. Various nonlinear phenomena are observed and comparisons with the theoretical results are made.

Chen, J. C.↗
NASA NTRS1975

Experiences in using modal synthesis within project requirements

Modal synthesis methods were developed for use by engineers for cost-effective solutions of large structural dynamics problems. Different methods were proposed by various investigators based upon comparative solutions of relatively simple structures using different forms of displacement functions. The application of modal synthesis methods to a large complex structure in a project environment is described. The considerations include analysis, hardware interfaces, schedules, tests, resources, and other project requirements. Good technical results were obtained through the use of an integrated analysis/test modal synthesis on both substructures and systems.

Garba, J. A.↗