Engineering Papers⌕ Search

Engineering topics

Carlos Malpica

Publications and source records attributed to Carlos Malpica.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

A Modeling Approach for Handling Qualities and Controls Safety Analysis of Electric Air Taxi Vehicles

The combination of modern advances in electric propulsion, fly-by-wire controls, autonomy, and increasing demand for short range air taxi operations, is currently producing an outburst of vehicle designs more diverse than ever before. Advanced software tools are needed to support the rapid and safe introduction of any design into the airspace, including the safety of the deployed flight control system and vehicle handling qualities. This paper presents a methodology for building air taxi vehicle models with distributed electric propulsion for use in analyzing flight control system safety at the conceptual design level.The approach builds on existing software tools capable of outputting aeromechanics-based linear perturbation models for Vertical Take-off and Landing vehicles with multiple rotors. Rotor torque inputs are then converted into equivalent voltage control inputs, and the linear state and input dynamics matrices are modified to include electric motor dynamics with common parameters for direct-current electric motors. The linear perturbation dynamics are then stitched across multiple operating points into a quasi-Linear Parameter Varying model that covers the full flight envelope. A Model Predictive Controller is developed for use with the full envelope model, and a tradeoff analysis between handling quality and motor requirements is demonstrated using a six passenger NASA air taxi reference design.

Urban Air Mobility↗
NASA NTRS2020

Mars Science Helicopter Conceptual Design

Robotic planetary aerial vehicles increase the range of terrain that can be examined, compared to traditional landers and rovers, and have more near-surface capability than orbiters. Aerial mobility is a promising possibility for planetary exploration as it reduces the challenges that difficult obstacles pose to ground vehicles. The first use of a rotorcraft for a planetary mission will be in 2021, when the Mars Helicopter technology demonstrator will be deployed from the Mars 2020 rover. The Jet Propulsion Laboratory and NASA Ames Research Center are exploring possibilities for a Mars Science Helicopter, a second-generation Mars rotorcraft with the capability of conducting science investigations independently of a lander or rover (although this type of vehicle could also be used assist rovers or landers in future missions). This report describes the conceptual design of Mars Science Helicopters. The design process began with coaxial-helicopter and hexacopter configurations, with a payload in the range of two to three kg and an overall vehicle mass of approximately twenty kg. Initial estimates of weight and performance were based on the capabilities of the Mars Helicopter. Rotorcraft designs for Mars are constrained by the dimensions of the aeroshell and lander for the trip to the planet, requiring attention to the aircraft packaging in order to maximize the rotor dimensions and hence overall performance potential. Aerodynamic performance optimization was conducted, particularly through airfoils designed specifically for the low Reynolds number and high Mach number inherent to operation on Mars. Rotor structural designs were developed that met blade frequency and weight targets, subject to material stress limits. The final designs show a substantial capability for science operations on Mars: a 31 kg hexacopter that fits within a 2.5 m diameter aeroshell could carry a 5 kg payload for 10 min of hover time or over a range of 5 km.

Wayne Johnson↗
NASA NTRSDate not supplied

Multirotor Configuration Trades Informed by Handling Qualities for Urban Air Mobility Application

Many contemporary Advanced Air Mobility (AAM), and more specifically, urban air mobility (UAM) vehicle designers are attracted to variable rotor speed-controlled designs with multiple rotors because of the great potential for mass savings compared to more traditional, variable blade pitch-controlled vehicles. These designs are based on the assumption that the stability and control of recreation or basic utility-sized drones can be scaled to larger passenger-sized vehicles. Previous work had shown the challenges in stabilizing passenger-sized quadcopters. In this study, power constraints were made less restrictive and varied, allowing more control power. Motor parameters such as efficiency, nominal voltage and current operating point, and rise time of the rotor speed controller step response were studied. By fixing the efficiency of the motor to 95% and assuming a motor voltage to current ratio of 2.0 (previously, assumed to be 1.0), the authors were able to stabilize the quadcopter in the roll axis because this allowed the vehicle to achieve adequate rise times between 0.4 and 0.8 s. This motor optimization was extended to a hexacopter and octocopter designed to the same payload size and mission as the quadcopter. The three vehicle configurations and their motor speed controllers were compared. It was found that while hexacopter and octocopter required more mass and overall power; all three configurations had similar margins required for control. However, the hexacopter and octocopter were able to use this power margin to achieve lower rise times (i.e. the vehicle responded more quickly to pilot inputs) than the quadcopter, with the octocopter having the lowest rotor response rise time of the three vehicle configurations studied.

Multirotor↗
NASA NTRSDate not supplied

Mars Science Helicopter: Conceptual Design of the Next Generation of Mars Rotorcraft

Robotic planetary aerial vehicles increase the range of terrain that can be examined, compared to traditional landers and rovers, and have more near-surface capability than orbiters. Aerial mobility is a promising possibility for planetary exploration as it reduces the challenges that difficult obstacles pose to ground vehicles. The first use of a rotorcraft for a planetary mission will be in 2021, when the Ingenuity Mars helicopter technology demonstrator will be deployed via the Perseverance rover. NASA’s Jet Propulsion Laboratory and NASA Ames Research Center are exploring possibilities for a Mars Science Helicopter, a second-generation Mars rotorcraft with the capability of conducting science investigations independently of a lander or rover (although this type of vehicle could also be used to assist rovers or landers in future missions). Two, large rotorcraft configurations are described: a hexacopter and a co-axial helicopter with a payload in the range of two to three kilograms and an overall vehicle mass of approximately twenty kilograms. Additionally, advancements in technology over the course of the study are applied to a rotorcraft of the same size and form as Ingenuity. Initial estimates of weight and performance were based on the capabilities of Ingenuity. Rotorcraft designs for Mars are constrained by the dimensions of the aeroshell and lander for the trip to the planet, constraining maximum rotor dimensions and, hence, overall performance potential. The effects of airfoils designed specifically for the low Reynolds number and high Mach number inherent to operation on Mars were studied. Rotor structural designs were developed that met blade frequency and weight targets, subject to material stress limits. The final designs are representative of the vehicle configurations required for a large range of future missions and will require relatively minor adaptations once science tasks are chosen. These designs will be compared to Ingenuity to demonstrate technology advancements developed during the study.

Mars Science Helicopter↗
NASA NTRSDate not supplied

Impact of Handling Qualities on Motor Sizing for Multirotor Aircraft with Urban Air Mobility Missions

Control models of three NASA Urban Air Mobility (UAM) reference vehicles (the quadrotor, octocopter, and Lift+Cruise (LPC)) were created and compared to determine the effect of rotor number and disk loading on control margin and design. The heave and yaw axes demand more actuator usage than the roll and pitch axes. Between heave and yaw, heave was the more demanding of the two because of the dependence of heave on the engine speed controller (ESC). When the feedback gains for all three vehicles were optimized to Level 1 handling qualities (HQs) specifications using CONDUIT, the ESC for the octocopter was the most stable and had the highest rise time (time for the rotor to respond to an input), while the LPC ESC was the least stable and had the smallest rise time. Rise time corresponds to the time required for rotor response. When actuator usage was translated to current margin, torque margin, and power margin, heave was the most demanding axis, followed by yaw, roll, and then pitch for all three vehicles. The results emphasize the importance of an accurate motor model within the control system architecture.

Impact↗
NASA NTRSDate not supplied

A Gaussian Process Enhancement to Linear Parameter Varying Models

Simulation and analysis for modern engineering systems now routinely requires the merging of multiple disciplines, physical-domains, time-scales, and data sets — all at ever increasing levels. These capabilities are especially needed in the domain of Advanced Air Mobility, where rapidly emerging vehicle designs are significantly more complex, while having to be both cost-effective and safe. To meet these engineering challenges, machine learning methods are an attractive option for merging models and data across multiple areas while providing uncertainty quantification and maintaining computational efficiency. This paper examines the use of Gaussian process machine learning to generalize and enhance the commonly used class of quasi-Linear Parameter Varying models for fast full-envelope simulation while also supporting control system design and analysis with model uncertainty. Gaussian process machine learning is selected because it: can fuse multiple data sets, enables an easy trade-off between data fitting and smoothing, provides model uncertainty quantification, scales well with increasing complexity, and does not generally require starting from a large training data set. To demonstrate the benefits of the approach, a robust stability analysis with Gaussian process uncertainty is shown for a NASA reference design of an electric quad-rotor air-taxi concept vehicle with motor parameter uncertainty.

Gaussian Process↗
NASA NTRSDate not supplied

Pilot Workload Rating Predictions Using Image Data and Recurrent Neural Networks

In this work, we augmented existing methods for estimating pilot workload ratings with deep neural networks trained using data from simulated flight tests in the Vertical Motion Simulator (VMS). We used an existing method, Spare Capacity Operations Estimator (SCOPE), along with a recurrent neural network and conducted comparison studies between the two methods individually, and when used together. We found that using both methods together can improve the result over using either approach alone. In our first test case, we achieved an improved linear correlation coefficient of 0.409 over that of SCOPE alone at 0.352 on the training dataset. Through cross validation, we also found that the results may be dependent on the split of training vs. validation data, and that further investigation should be conducted to understand what additional inputs to the neural network model should be made.

Image Data↗
NASA NTRSDate not supplied

Evaluation of Heave Disturbance Rejection and Control Response Criteria on the Handling Qualities Evaluation of Urban Air Mobility (UAM) eVTOL Quadrotors Using the Vertical Motion Simulator

The first piloted handling qualities study of an urban air mobility (UAM) vehicle leveraging the Vertical Motion Simulator (VMS) at NASA Ames Research Center was conducted in Spring 2021. The VMS provides a unique capability to reduce risk by assessing and iterating control designs. Minimal sources currently exist to provide performance and handling qualities data for large, rotor speed-controlled vehicles outside of the software environment. The study compares multiple handling qualities performance configurations for rotor speed and blade pitch-controlled variants of a six-passenger quadrotor conceptual design model developed by the NASA Revolutionary Vertical Lift Technology (RVLT) Project. Additionally, both ADS-33 and a tailored set of performance standards (notionally representing the agility required of a UAM mission) are examined under conditions with and without light turbulence. Preliminary results did show significant variation in ratings based on the set of standards utilized, controller tuning to either Level 1 or boundary Level 1/ Level 2 conditions, and presence or lack of turbulence. A custom approach and landing maneuver was also designed to bring these evaluation tasks together in a more comprehensive application.

Handling Qualities↗
NASA NTRSDate not supplied

Analysis of Handling Qualities and Power Consumption for Urban Air Mobility (UAM) eVTOL Quadrotors with Degraded Heave Disturbance Rejection and Control Response

A piloted handling qualities study of urban air mobility (UAM) electric vertical take-off and landing (eVTOL) quadrotors was performed utilizing the Vertical Motion Simulator (VMS) facility at NASA Ames Research Center. Rotor speed and variable pitch-controlled variants of a six-passenger conceptual design vehicle were assessed with different levels of degradation to control response and disturbance rejection bandwidth (DRB) in the heave axis. In previous work, preliminary trends across several handling quality rating categories reflected the effects of these degradations. Additionally, the impact of using different test standards and turbulence on the ratings were discussed. This paper elaborates on those results, but also provides insight into unexpected trends observed during the study including: a disharmony in attitude response, subpar ratings for the baseline Level 1 performance vehicle, and excessive drift and yaw couplings observed in a lateral reposition maneuver. Moreover, shortcomings of the handling quality scales and comparisons of power consumption among the vehicles in the various test conditions are presented.

Handling Qualities↗
NASA NTRSDate not supplied

Handling Qualities Considerations in Control Allocation for Multicopters

Due to multicopters’ role in advanced air mobility, there has been an increasing interest in handling qualities. This paper investigates the effect of control allocation of multicopters on handling qualities. Typically, multicopter aircraft are trimmed with equal speed on each rotor. The force generated by each rotor can be modeled, where thrust and torque of the rotor are related to the square of the rotor speed. The dynamic equations indicate that trimming pairs of motors at different RPM results in an increase of control effectiveness in the associated axis, improving bandwidth and disturbance rejection. A tradeoff occurs where power usage is no longer optimized, but handling qualities are improved in that control axis. A blade element model for multicopter, RMAC, was used to simulate how this off-nominal control allocation would affect the dynamics of a multicopter. System identification flight tests were used to validate the trends seen in RMAC. Control systems were optimized to provide improved disturbance rejection bandwidth in the axis associated with increased rotational speed. Unmanned mission task elements were performed in flight test, showing improved tracking in the lateral axis by using off-nominal mixing to increase trim speed on the rolling motors.

Handling Qualities↗
NASA NTRSDate not supplied

Integrated Handling Qualities Safety Analysis For Conceptual Design of Urban Air Mobility Vehicles

The recent emergence of distributed electric propulsion Vertical Takeoff and Landing (VTOL) aircraft has created a rapid introduction of new design concepts with unique stability and control characteristics. A challenge to realizing the full potential of these vehicles for urban transportation is to gain public acceptance which is largely driven by flight safety. This paper describes ongoing research to address the feasibility of integrating flying qualities safety metrics into conceptual design of VTOL Urban Air Mobility (UAM) vehicles. The discussion is composed of the approach and progress toward a toolbox that integrates with existing NASA rotorcraft design software and processes. Several key challenges are highlighted including modeling requirements for failures, identification of critical failures, and capturing critical failures, with robustness to model uncertainty. A discussion of requirements for safety metrics, specific to UAM vehicles, as well as the effects of the control system design is also included. Results to date have demonstrated the degradation in flying qualities metrics due to propulsion failures.

George Altamirano↗
NASA NTRSDate not supplied

Flying Qualities Analysis and Piloted Simulation Testing of a Lift+Cruise Vehicle with Propulsion Failures in Hover and Low-Speed Conditions

The recent emergence of electric-Vertical Take-Off and Landing (eVTOL) vehicles for Urban Air Mobility (UAM) applications has resulted in a wide variety of configurations with unique stability and control characteristics. NASA is currently conducting research to develop conceptual design tools to accelerate public acceptance of these vehicles which includes requirements for safety during failure scenarios. This paper summarizes progress toward a toolbox for predicting flying qualities of eVTOL vehicles during critical propulsion failures that could impact the allowable design of the vehicle geometry or control system. Key topics include unique vulnerabilities of eVTOL/multirotor vehicles to propulsion failures, relevant flying qualities design metrics, and simulation modeling requirements for assessing flying qualities degradation due to failures. Results of a piloted simulation study conducted in the NASA Ames Vertical Motion Simulator (VMS) are presented. The VMS experiment was designed to assess and validate key handling qualities and safety design metrics for propulsion failures. These results show the correlation between control system design requirements and the degradation in handling qualities for various propulsion failures.

George Altamirano↗
NASA NTRSDate not supplied

Handling Qualities of Multirotor RPM-Controlled Electric-Vertical Take-Off and Landing (eVTOL) Aircraft for Urban Air Mobility (UAM)

A paradigm shift in rotorcraft design is being led by the prospect of propulsive forces being distributed across multiple rotors, such that each rotor can be directly driven by a dedicated electric motor. Crucially, some designers attempt to utilize these direct-drive mechanisms as the sole form of primary flight control. The feasibility of this design choice remains to be proven at the scales required for passenger transport. The paper presents a preliminary handling qualities analysis, for a six-passenger (1,200 lb payload) electric Hexacopter conceptual design, which shows that Level 1 handling qualities for limited agility operations are possible, provided that electric powertrains can deliver transient peak torques twice as high as the rated continuous torque of the conceptual design. Preliminary predictions are then substantiated by the results from a piloted handling qualities evaluation conducted in the NASA-Ames Vertical Motion Simulator (VMS). Three eVTOL configurations (a quadrotor, a hexacopter and a lift+cruise) with flight control laws implementing different levels of stability augmentation (Attitude Command-Attitude Hold and Translational Rate Command response types) were evaluated in four low speed and hover tasks requiring various levels of agility and precision.

UAM↗
NASA NTRSDate not supplied

Enhanced Flight Dynamics Models with Aerodynamic Interference for Real-Time Simulation of VTOL Concept Vehicles

In an effort to establish common models to support the Advanced Air Mobility (AAM) community, NASA has designed a fleet of VTOL configuration reference models. Advanced Rotorcraft Technologies (ART) in cooperation with the NASA Ames Aeromechanics branch has developed FLIGHTLAB simulation models for several of these AAM VTOL concept vehicles. These simulation models are real-time capable while maintaining accurate flight dynamic characteristics with enhanced interference simulation by extracting important modeling parameters from Viscous Vortex Particle Method (VVPM). The focus of this paper is threefold. First, it introduces the simulation models developed and describes their modeling characteristics important to control and flight dynamics simulation. Second, the method for deriving the interference coefficients between model components such as rotors and wings is outlined. Implementation of the method for the lift+cruise and tiltwing models are discussed in detail. Third, the accuracy of the interference enhancement is assessed, with emphasis placed on the impacts to trim and flight dynamic characteristics. The interference enhancement method is further used to evaluate configuration design decisions by quantifying performance aspects of interference. This research effort culminated in simulation models for the AAM VTOL concept vehicles, with proper interference and real-time capability.

Flight Dynamics↗
NASA NTRSDate not supplied

Mars Sample Recovery Helicopter: Rotorcraft to Retrieve the First Samples from the Martian Surface

The Mars Sample Return Mission (MSR) will carry the next set of Mars helicopters, Sample Recovery Helicopters (SRHs), to the Martian surface. After successfully demonstrating extraterrestrial flight in 2021, Ingenuity has acted as a “scout” for the Perseverance rover while the rover gathers samples of Martian soil. In 2028, the MSR mission will launch a lander and two Ingenuity-sized SRHs to retrieve these samples. These will be the first samples of the Martian surface delivered to Earth. The SRH project will maintain heritage from Ingenuity’s design when possible. However, several key changes must be made, including a ground mobility system, a robotic arm for tube manipulation, and the ability to carry the weight of a science payload (the sample tubes). In addition, the onboard software and cameras will be upgraded, and the rotor radius will be increased. Furthermore, new rotor performance and flight dynamics models and thorough characterization of vehicle limits will be required. The new vehicle design will be described, as well as validation and verification efforts to date.

Rotorcraft↗