Engineering Papers⌕ Search

Engineering topics

Bhattacharya, Sumit

Publications and source records attributed to Bhattacharya, Sumit.

36 records · Page 2

Improving stability of ALD ZrN thin film coatings over U-Mo dispersion fuel

Atomic layer deposition (ALD) of ZrN is a candidate technology for coating U-Mo dispersion fuel as a diffusion barrier coating. During the early development stages of the coating the ZrN deposition showed to be mechanically unstable and ultimately resulted in spalling. Based on experimental outcomes it was found that instabillity can be eliminated through the introduction of a thin amorphous (a) Al 2 O 3 interlayer coating deposited in between the ~1-μm thick ZrN and the U-Mo. substrate. To elucidate these findings simulations were performed with density functional theory (DFT) to measure work of adhesions at different interfaces while finite element modeling (FEM) was performed to measure the residual stress distribution. DFT indicated that the ZrN coating deposited over (a)-Al 2 O 3 is ~2.5 times stronger when compared to direct deposition over U or UO 2 substrate. While calculations from FEM recognized; (1) large stress concentrations can originate from the irregularly distributed native surface oxides (UO 2 ) over U-Mo and (2) stress concentrations can be reduced if those surface UO 2 can be modified to a uniform layer (achieved after application of a 8 nm (a)-Al 2 O 3 interlayer). These results provided explanations and confirmed the role played by interlayer in eliminating the original mechanical instability of the ZrN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nanocrystalline ZrN thin film development via atomic layer deposition for U-Mo powder

Zirconium nitride (ZrN) thin film deposited via thermal atomic layer deposition (ALD) has been recently chosen as a candidate technology for application of a diffusion barrier coating on the low enriched uranium alloy powder considered in the NNSA research reactor conversion program. Reported here is the first instance of using ALD for coating actinide materials. For this study, a modified ALD system was constructed to produce one micron thick zirconium nitride (ZrN) coating over spherical particulate of natural uranium-molybdenum (U-Mo) based fuel. The ALD system was designed to have a rotating drum system, with provisions for facilitating sequential exposures of chemicals such as tetrakis dimethyl amido zirconium (TDMAZr) and ammonia (NH 3 ) in order to deposit ZrN. The ALD system was successful in developing a highly conformal ZrN coating covering every individual U-7Mo particle. This article describes the ZrN film synthesis details and reports the produced microstructure and composition of the ALD ZrN as deposited on fuel particulates. The as-fabricated coating was determined to have a nanocrystalline structure in the cubic-ZrN (cF8) phase. It exhibited a dense microstructure with adequate interfacial bonding. TEM-EELS characterization demonstrated that the coating contains a very low amount of oxygen impurity. To understand the potential microstructural evolution for ALD ZrN during reactor operation, an in-situ heavy ion (Kr) irradiation experiment was performed at the IVEM-Tandem facility. A total fluence of 7.5 x 10 15 ions/cm 2 (similar to 10 dpa) was achieved, and apart from minor grain coarsening in the ALD ZrN coating, no significant radiation effects were observed.

36 MATERIALS SCIENCE↗

Composite matrix using a hybrid deposition technique

Provided herein are methods of forming a composite matrix on a porous substrate or a non-porous substrate, the methods including subjecting the substrate to a first deposition method to apply a first coating including first ceramic or metallic particles and form a coated substrate and subjecting the coated substrate to atomic layer deposition to apply a second coating and form the composite matrix, wherein the second coating includes second ceramic or metallic particles.

36 MATERIALS SCIENCE↗

Adhesion of ZrN and Al 2 O 3 coatings on U metal from first-principles

To understand the role of alumina layer in the adhesion of ZrN coating on U-Mo surface using atomic layer deposition (ALD) technique, we investigate the interfaces of ZrN/U, Al 2 O 3 /U, and ZrN/Al 2 O 3 using first-principles density-functional theory calculations. The preferred interfacial plane orientation relationships and terminations for all the interfaces are predicted. Calculations show that both lattice mismatch and interfacial bonding play crucial roles in determining the adhesion strength of ZrN and Al 2 O 3 coatings on U metal surface. The strength of Al 2 O 3 /U and ZrN/Al 2 O 3 interfaces are found to be substantially higher than that of ZrN/U interface. The strong interfacial adhesion of Al 2 O 3 /U and ZrN/Al 2 O 3 interfaces is ascribed to the formation of ionic bonds at the interface, as compared to weak metallic bonds formed in ZrN/U interface. Furthermore, the formation of metal-oxygen ionic bonds at interface explains the role of alumina layer in the improved adhesion of ZrN coating on U-Mo surface.

36 MATERIALS SCIENCE↗

First-principles study of fracture toughness enhancement in transition metal nitrides

Due to its superior thermophysical properties, ZrN thin film has been studied as a diffusion barrier for a variety of applications. However, cracks and delamination of ZrN coating takes place because of its brittleness. To identify new diffusion barrier materials with improved fracture toughness, we systematically studied the mechanical properties, surface energies and fracture toughness of IVB, VB and VIB transition metal mononitrides using first-principles calculations. TiN and HfN show slightly better toughness than ZrN. To improve the toughness of ZrN, we investigated the fracture toughness of ZrN alloyed with 25% IVB, VB and VIB transition metal nitrides. TiN, HfN and TaN was found to be able to increase the fracture toughness of ZrN through alloying. Meanwhile, we predicted the interfacial fracture toughness of ZrN/TiN and ZrN/HfN interfaces to evaluate the fracture toughness of ZrN/TiN and ZrN/HfN multilayer structures. Both ZrN/TiN and ZrN/HfN films exhibit higher interfacial fracture toughness than that of ZrN single film. Furthermore, alloying and multilayer structures are promising approaches to enhance the toughness of brittle ZrN film.

36 MATERIALS SCIENCE↗

Interaction between Al and atomic layer deposited (ALD) ZrN under high-energy heavy ion irradiation

Uranium-molybdenum (U-Mo) particles dispersed in an aluminum matrix is the most promising candidate fuel to convert high-power research and test reactors in Europe from using high-enriched to using low-enriched fuel. However, chemical interaction between the U-Mo and the Al matrix leads to undesirable fuel behavior. Zirconium nitride (ZrN) is used as a diffusion barrier between the U-Mo fuel particles and the Al matrix. To understand the potential microstructural evolution of ZrN during irradiation, a high-energy heavy ion (84 MeV Xe) irradiation experiment was performed on atomic layer deposited (ALD) nanocrystalline ZrN deposited on an Al plate. A fluence of 1.86 x 10 17 ions/cm 2 , or 90.3 dpa was reached during this experiment. Both analytic transmission electron microscopy (TEM) and synchrotron microbeam X-ray diffraction (ARD) techniques were utilized to investigate the kinetics of radiation-induced grain growth of ZrN at various radiation doses based on the Williamson-Hall analyses. The grain growth kinetics can be described by a power law expression, D n - D$n\atop{0}$ = K phi, with n = 5.1. The Al-ZrN interaction products (Al 3 Zr and AIN) created by radiation-induced ballistic mixing/radiation-enhanced diffusion and their corresponding formation mechanism were determined from electron diffraction and elemental composition analysis. These experimental results were confirmed by first principle thermodynamic density functional theory (DFT) calculations. The results from this ion irradiation study were also compared to in-pile irradiation data from physical vapor deposited (PVD) ZrN samples for a comprehensive evaluation of the interaction between Al and ZrN and its influence on diffusion barrier performance.

36 MATERIALS SCIENCE↗

Nano-crystallization induced by high-energy heavy ion irradiation in UO 2

Here, advanced microstructure investigations of the high-burnup structure (HBS) in UO 2 produced by high-dose 84 MeV Xe ion irradiation are reported. Spark plasma sintered micro-grained UO 2 was irradiated to 1357 dpa at 350 degrees C. The characteristic nano-grains and micro-pores of the HBS were formed. The grain size and grain boundary misorientation distributions of the HBS were measured using transmission electron microscopy based orientation imaging microscopy. Grain polygonization due to accumulation of radiation-induced dislocations was found to be the mechanism of nano-crystallization. The morphology of Xe bubbles was quantitatively investigated. Finally, this study provides crucial references for advanced fuel performance modeling of high-burnup UO 2 .

36 MATERIALS SCIENCE↗

Microstructure Investigations of U{sub 3}Si{sub 2} Irradiated by Heavy Ions at LWR Temperatures

Searching for a nuclear fuel material with enhanced accident tolerance compared to the conventional UO{sub 2} fuel is one of the key objectives of the accident tolerant fuel (ATF) campaign. Having both high thermal conductivity and high uranium load, U{sub 3}Si{sub 2} is expected to provide lower operating temperature/stored energy and advantageous neutron economy as a light water reactor (LWR) fuel material. Therefore, U{sub 3}Si{sub 2} has been regarded as a promising candidate fuel material by the ATF community. To evaluate the qualification of U{sub 3}Si{sub 2} as an ATF fuel in LWRs, its fuel performance during both steady-state operation and power transients must be well understood. As a typical nuclear fuel material applied in research reactors, the fuel performance of U{sub 3}Si{sub 2} at low temperatures (<300 deg. C) has been extensively studied through both experimental and computational approaches. However, under LWR conditions, the temperature of U{sub 3}Si{sub 2} can go beyond 600 deg. C. In that case, the references collected in U{sub 3}Si{sub 2}'s applications in research reactors are inadequate for the validation of U{sub 3}Si{sub 2} as an LWR ATF. Experimental efforts that are dedicated to the LWR conditions must be made to help examine U{sub 3}Si{sub 2}'s qualifications as well as provide valuable references for the development related models in advanced fuel performance code. Gaseous fission products accumulate in nuclear fuel during operation and form fission gas bubbles. The evolution of those fission gas bubbles results in increase of volume (swelling), degradation of thermal conductivity, and eventually fission gas release, compromising the integrity and performance of fuel elements in multiple aspects. Hence, fission gas behavior is one of the most important components of fuel performance. In-pile irradiation and corresponding post-irradiation examinations (PIEs) undoubtedly provide most reliable information on the actual performance of a nuclear fuel. However, the high cost and long lead time involved in in-pile irradiation limit its wide applications. On the other hand, heavy ion irradiation is capable of simulating the neutron effects on materials, especially the behavior of energetic fission fragments in nuclear fuel materials, to a considerable extent. Therefore, heavy ion irradiation was used in this study to investigate the microstructural evolution of U{sub 3}Si{sub 2} under LWR-temperature irradiation, focusing on the difference from low temperature irradiation and fission gas behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In situ synchrotron investigation of grain growth behavior of nano-grained UO 2

Here, we report on the study of grain growth kinetics in nano-grained UO 2 samples. Dense nano-grained UO 2 samples with well-controlled stoichiometry and grain size were fabricated using the spark plasma sintering technique. To determine the grain growth kinetics at elevated temperatures, a synchrotron wide-angle X-ray scattering (WAXS) study was performed in situ to measure the real-time grain size evolution based on the modified Williamson-Hall analysis. The unique grain growth kinetics of nanocrystalline UO 2 at 730 °C and 820 °C were observed and explained by the difference in mobility of various grain boundaries.

36 MATERIALS SCIENCE↗

Short communication on " In-situ TEM ion irradiation investigations on U 3 Si 2 at LWR temperatures"

Here, the radiation-induced amorphization of U 3 Si 2 was investigated by in-situ transmission electron microscopy using 1 MeV Kr ion irradiation. Both arc-melted and sintered U3Si2 specimens were irradiated at room temperature to confirm the similarity in their responses to radiation. The sintered specimens were then irradiated at 350 °C and 550 °C up to 7.2 × 10 15 ions/cm 2 to examine their amorphization behavior under light water reactor (LWR) conditions. U 3 Si 2 remains crystalline under irradiation at LWR temperatures. Oxidation of the material was observed at high irradiation doses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synchrotron Microdiffraction Study of Heavy-Ion-Irradiated Uranium-Molybdenum Dispersion Fuel

There has been an ongoing effort by the Department of Energy Office of Material Management and Minimization to convert research and test reactors from high-enriched to low-enriched uranium fuels. Uranium-molybdenum alloy fuel dispersed in an aluminum matrix (UMo-Al dispersion fuel) has emerged as the leading candidate fuel for converting the remaining high-power research reactors in Europe. One of the primary barriers to using this fuel type is the deleterious reaction of UMo with Al. Depending on the operating temperature of the reactor, this interaction layer can be amorphous under irradiation and allows for the accumulation of fission gas products in large bubbles, leading to unacceptable swelling of the fuel. Therefore, detailed characterization of the phases that form within the fuel and in the interaction layer is critical to understanding, and controlling, UMo-Al dispersion fuel behavior under irradiation. Furthermore, the phase stability of the UMo fuel is of great importance, as the alpha-UMo phase has undesirable swelling compared to the metastable gamma-UMo phase. Heavy ion irradiation was used to reproduce the interaction layer that develops in-reactor. Samples of both the fuel and interaction layer formed under ion irradiation were examined using the high-energy x-ray microdiffraction technique at the Advanced Photon Source (APS) at Argonne National Laboratory to examine the microstructure of the interaction layer. The high-resolution phase information obtained in this experiment provides a valuable basis for understanding the evolution of UMo-Al dispersion fuel under irradiation and as input for computational studies to improve predictive capabilities. Phase information for in-pile fuels can currently be determined from TEM samples (limited sample volume, limiting statistics), or by extrapolation from SEMEDS analysis. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TEM Characterization of U-Mo Irradiated with High-Energy Xe Ions

U-Mo alloys (with 7-10 wt.% Mo) with a low U-235 enrichment (< 20%) have been developed to be used in high-performance research and test reactors, replacing the current highly enriched uranium (HEU) fuels. A number of in-pile irradiation tests of U-Mo fuels show that drastic microstructural changes occurred during reactor irradiation, including the formation of U-Mo-Al interaction products and large gas-filled pores. These microstructural changes might lead to breakaway swelling and deterioration of plate mechanical integrity. Hence, it is critical to understand the underlying mechanisms of these microstructural changes in order to improve the irradiation behavior of UMo fuels. Heavy ion irradiation was employed in this study to investigate separate effects of the irradiation behavior of U-Mo fuels. 1.7 mm diameter disks punched out from UMo/ Al dispersion fuel mini-plates were irradiated with 84 MeV Xe ions at the ATLAS accelerator at Argonne National Laboratory (ANL). This particular ion source was selected for two reasons: (1) to simulate the irradiation response of the fuel to fission fragment bombardments, and (2) to study fission gas behavior, as fission gas bubble formation and growth is the primary cause of U-Mo fuel swelling. The ion-irradiated samples have been characterized with scanning electron microscopy (SEM). This study focuses on the characterization of the samples using transmission electron microscopy (TEM). With the high magnification details, microstructures in U-Mo along the ion penetration depth were revealed. The U-7Mo/Al dispersion fuel sample irradiated with 84 MeV Xe ions to a dose of 2.9 x 10{sup 17} ions/cm{sup 3} was characterized using TEM. The TEM results exhibit that the sample microstructure varies along the ion penetration depth. Near the sample surface (zone A) is a layer of nano-crystalline U-Mo-Al interdiffusion product. After passing through zone A, the Xe ions resided in zone B, where gas bubbles formed in U-Mo. TEM images of this region displayed that large gas bubbles formed on grain boundaries and high-density nano-bubbles lay inside grains. The random distribution of intragranular bubbles indicates that the irradiation conditions of this sample cannot lead to gas bubble superlattice formation. Outside of the Xe penetration depth (zone C), significant amount of α-uranium precipitates were identified. The fact that no α-uranium precipitates were found in zone B suggests that the dose rate in this irradiation is sufficient to facilitate a phase reversal by means of a displacement spike mechanism. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-energy synchrotron study of in-pile-irradiated U–Mo fuels

Here synchrotron scattering analysis results on U–7wt.%Mo fuel specimens irradiated in the Advanced Test Reactor to three burnup levels (3.0, 5.2, and 6.3 × 1021 fission/cm3) are reported. Mature fission gas bubble superlattice was observed to form at intermediate burnup. The superlattice constant was determined to be 11.7 and 12.0 nm by wide-angle and small-angle scattering respectively. Grain sub-division takes place throughout the irradiation and causes the collapse of the superlattice at high burnup. The bubble superlattice expands the U–Mo lattice and acts as strong sink for radiation-induced defects. The evolution of dislocation loops was, therefore, suppressed until the bubble superlattice collapsed.

metallic nuclear fuel↗

Experimental studies of Micro- and Nano-grained UO 2 : Grain Growth Behavior, Sufrace Morphology, and Fracture Toughness

This activity is supported by the US Nuclear Energy Advanced Modeling and Simulation (NEAMS) Fuels Product Line (FPL) and aims at providing experimental data for the validation of the mesoscale simulation code MARMOT. MARMOT is a mesoscale multiphysics code that predicts the coevolution of microstructure and properties within reactor fuel during its lifetime in the reactor. It is an important component of the Moose-Bison-Marmot (MBM) code suite that has been developed by Idaho National Laboratory (INL) to enable next generation fuel performance modeling capability as part of the NEAMS Program FPL. In order to ensure the accuracy of the microstructure-based materials models being developed within the MARMOT code, extensive validation efforts must be carried out. In this report, we summarize the experimental efforts in FY16 including the following important experiments: (1) in-situ grain growth measurement of nano-grained UO 2 ; (2) investigation of surface morphology in micrograined UO 2 ; (3) Nano-indentation experiments on nano- and micro-grained UO 2 . The highlight of this year is: we have successfully demonstrated our capability to in-situ measure grain size development while maintaining the stoichiometry of nano-grained UO 2 materials; the experiment is, for the first time, using synchrotron X-ray diffraction to in-situ measure grain growth behavior of UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of current density on microstructure of pulse electrodeposited tin coatings

Pulse electrodeposited tin coatings on copper substrate have been synthesized from an aqueous solution containing sodium stannate (Na{sub 2}SnO{sub 3}.3H{sub 2}O) and sodium hydroxide (NaOH). The effect of current density on surface morphology of the deposits has been investigated. As deposited coatings are characterized by X-ray diffraction, scanning electron microscopy, electron backscatter diffraction, and line profile analysis. The X-ray diffraction analysis shows that the deposits consist of tetragonal ({beta}-Sn) structure with microcrystalline grains. The deposits plated at lower current density exhibit (110) texture which decreases with increasing current densities. The effects of current density on Cu-Sn diffusion and whisker growth of the electrodeposited tin coatings are also reported here. - Highlights: Black-Right-Pointing-Pointer Pulse electrodeposition of Sn from aqueous alkaline solution without adding any organic additive. Black-Right-Pointing-Pointer Effect of current density on morphology and whisker growth in tin coatings aged for 1 year. Black-Right-Pointing-Pointer Solution bath is stable and can be operated over a wide range of current density.

36 MATERIALS SCIENCE↗