Engineering topics

Bauer, Steven X. S.

Publications and source records attributed to Bauer, Steven X. S..

42 records · Page 3

NASA NTRS1989

A natural flow wing design employing 3-D nonlinear analysis applied at supersonic speeds

A wing-design study has been conducted on a 65-deg-swept leading-edge delta wing in which a near-conical geometry was employed to take advantage of the naturally occurring conical flow which arises over such a wing in a supersonic flow field. Three-dimensional nonlinear analysis methods were used in the study. In preliminary design, wing planform, design conditions, and near-conical concept were derived and a baseline standard wing (conventional airfoil distribution) and a baseline near-conical wing were chosen. During the initial analysis, a full-potential solver was employed to determine the aerodynamic characteristics of the baseline standard delta wing and the near-conical delta wing. Modifications due to airfoil thickness, leading-edge radius, and camber were then applied to the baseline near-conical wing. The final design employed a Euler solver to analyze the best wing configurations found in the initial design, and to extend this study to develop a more refined wing. Benefits due to each modification are discussed, and a final natural flow wing geometry is chosen and its aerodynamic characteristics are compared with the baseline wings.

Bauer, Steven X. S.↗

NASA NTRS1989

Influence of wing geometry on leading-edge vortices and vortex-induced aerodynamics at supersonic speeds

An assessment of the influence of wing geometry on wing leading-edge vortex flows at supersonic speeds is discussed as well as the applicability of various aerodynamic codes for predicting these results. A series of delta-wing wind-tunnel models were tested in the NASA Langley Research Center Unitary Plan Wind Tunnel over a Mach number range from 1.6 to 4.6. The data show that wing airfoil has a significant impact on the localized loading on the wing. The experimental data for the flat wings were compared with results from full-potential, Euler, and Parabolized Navier-Stokes (PNS) computer codes. The theoretical evaluation showed that the full-potential analysis predicted accurate results for the attached-flow (alpha = 0 deg) conditions and that the Euler and PNS analyses made reasonable predictions for both attached and separated flow conditions.

Wood, Richard M.↗

NASA NTRS1988

Configuration trade and code validation study on a conical hypersonic vehicle

A study has been conducted on a generic wing-cone transatmospheric vehicle at Mach numbers form 2.5 to 4.5. The objectives of the study were to experimentally define the aerodynamic characteristics of the vehicle and evaluate several computational aerodynamic prediction methods through comparison with the experimental results. The baseline wing-cone configuration fuselage consisted of a 5 deg half-angle cone forebody, cylindrical midbody, and 9 deg truncated cone afterbody. The 4-percent-thick diamond airfoil wing had an aspect ratio of 1. Several configuration variables were investigated to provide trade information on canard, wing-position and incidence, vertical tail, and nose bluntness effects. Results of the study show that wing-position and wing-incidence effects on the longitudinal aerodynamic characteristics can be significantly influenced by wing-body interference. The use of positive wing incidence to provide favorable forebody orientation for possible inlet performance improvement is accompanied by trim drag and lift-drag ratio penalties. The lateral-directional stability characteristics were strongly influenced by the location of the vertical tails. The higher-order full-potential method provided better estimates of the aerodynamic characteristics than either the linearized supersonic potential method or the tangent-cone/tangent-wedge/shock-expansion on method.

Covell, Peter F.↗

NASA NTRS1988

Reduction of crossflow shock-induced separation with a porous cavity at supersonic speeds

The effectiveness of wing surface porosity in reducing boundary-layer separation induced by a cross flow shock on a conical wing in a supersonic flow was investigated in tests conducted in the NASA Langley Research Center Unitary Plan Wind Tunnel, at a Reynolds number of 2 mln/ft at Mach numbers 1.62, 1.70, 1.86, and 2.00 and with the angle of attack varying between -2 and 10 deg. A porous cavity was installed in a 57 deg swept conical wing at a location where a cross flow shock had been observed in previous tests. The porosity was varied from 11 to 22 percent, the pore hole diameter was varied from 0.025 to 0.050 in., and the cavity depth varied from 0.067 to 0.255 in. It was found that a hole of 0.025 in. in diameter is more effective than a 0.050-in. hole. However, the effectiveness of the larger holes could be increased by reducing the cavity depth, causing a closed-cavity type flow condition.

Bauer, Steven X. S.↗

NASA NTRS1988

Evaluation of a three-dimensional empirically derived wing at supersonic speeds

A novel wing design concept is introduced which takes advantage of the existence of conical flow at supersonic speeds. The present wing design concept is to create a near conical wing geometry by redistributing airfoils in a spanwise direction. In addition, a set of graphs which review the supersonic aerodynamics of delta wings have been employed to select a design wing sweep and Mach number. An iteration through the wing design logic resulted in the selection of a 65 deg swept delta wing and a design Mach number of 1.62. Theoretical analysis was performed with a nonlinear full-potential analysis method to assess the merits of the wing design approach. The analysis showed large reductions in drag due to lift compared to delta wings configured with traditional thickness and airfoil distributions.

Wood, Richard M.↗

NASA NTRS1988

Experimental and theoretical study of the effects of wing geometry on a supersonic multibody configuration

An experimental and theoretical investigation of planform effects on a low-fineness ratio multibody configuration was conducted in NASA-Langley Research Center's Unitary Plan Wind Tunnel at Mach number of 1.6, 1.8, 2.0 and 2.16. Experimental and theoretical values of lift, drag, and pitching moment as well as surface pressures were obtained on several configurations which varied in both outboard-wing panel and inboard-wing panel planforms. The three outboard-wing panels were a 65 -deg delta and two trapezoidal wing planforms. An unswept and a 60-deg swept inboard-wing panels were also tested. The purpose of the study was to determine the effect of wing planform on the supersonic aerodynamics. The large trapezoidal wing provided increased performance over the small trapezoidal wing primarily due to a reduction in the zero-lift drag coefficient. The swept inboard-wing panel planforms provided a slightly higher L/D than the unswept inboard-wing panel due to a minimal improvement in zero-lift drag. Linear-theory aerodynamic codes were used to analyze the effect of planform on the supersonic aerodynamics and were found to generally produce adequate results.

Bauer, Steven X. S.↗