Engineering topics
Publications and source records attributed to Bauer, Steven X. S..
The goal in this effort is to analyze the baseline TCA concept at transonic and supersonic cruise, then apply the natural flow wing design concept to obtain multipoint performance improvements. Analyses are conducted with OVERFLOW, a Navier-Stokes code for overset grids, using PEGSUS to compute the interpolations between the overset grids.
A device for controlling pressure loading of a member caused by a fluid moving past the member or the member moving through a fluid. The device consists of a porous skin mounted over the solid surface of the member and separated from the solid surface by a plenum. Fluid from an area exerting high pressure on the member may enter the plenum through the porous surface and exit into an area exerting a lower pressure on the member, thus controlling pressure loading of the member. A transpirational control device controls the conditions within the plenum thus controlling the side force and yaw moment on the forebody.
A 1990 research program that focused on the development of advanced aerodynamic control effectors (AACE) for military aircraft has been reviewed and summarized. Data are presented for advanced planform, flow control, and surface contouring technologies. The data show significant increases in lift, reductions in drag, and increased control power, compared to typical aerodynamic designs. The results presented also highlighted the importance of planform selection in the design of a control effector suite. Planform data showed that dramatic increases in lift (greater than 25%) can be achieved with multiple wings and a sawtooth forebody. Passive porosity and micro drag generator control effector data showed control power levels exceeding that available from typical effectors (moving surfaces). Application of an advanced planform to a tailless concept showed benefits of similar magnitude as those observed in the generic studies.
A 1990 research program that focused on the development of advanced aerodynamic control effectors (AACE) for military aircraft has been reviewed and summarized. Data are presented for advanced planform, flow control, and surface contouring technologies. The data show significant increases in lift, reductions in drag, and increased control power, compared to typical aerodynamic designs. The results presented also highlighted the importance of planform selection in the design of a control effector suite. Planform data showed that dramatic increases in lift (greater than 25%) can be achieved with multiple wings and a sawtooth forebody. Passive porosity and micro drag generator control effector data showed control power levels exceeding that available from typical effectors (moving surfaces). Application of an advanced planform to a tailless concept showed benefits of similar magnitude as those observed in the generic studies.
A discussion of knowledge and Knowledge- Based design as related to the design of aircraft is presented. The paper discusses the perceived problem with existing design studies and introduces the concepts of design and knowledge for a Knowledge- Based design system. A review of several Knowledge-Based design activities is provided. A Virtual Reality, Knowledge-Based system is proposed and reviewed. The feasibility of Virtual Reality to improve the efficiency and effectiveness of aerodynamic and multidisciplinary design, evaluation, and analysis of aircraft through the coupling of virtual reality technology and a Knowledge-Based design system is also reviewed. The final section of the paper discusses future directions for design and the role of Knowledge-Based design.
Commercial transports as well as fighter aircraft of the future are being designed with very low drag (friction and pressure). Concurrently, commuter airports are being built or envisioned to be built in the centers of metropolitan areas where shorter runways and/or reduced noise footprints on takeoff and landing are required. These requirements and the fact that drag is lower on new vehicles than on older aircraft have resulted in vehicles that require a large amount of braking force (from landing-gear brakes, spoilers, high-lift flaps, thrust reversers, etc.). Micro-drag generators (MDGs) were envisioned to create a uniformly distributed drag force along a vehicle by forcing the flow to separate on the aft-facing surface of a series of deployable devices, thus, generating drag. The devices are intended to work at any speed and for any type of vehicle (aircraft, ground vehicles, sea-faring vehicles). MDGs were applied to a general aviation wing and a representative fuselage shape and tested in two subsonic wind tunnels. The results showed increases in drag of 2 to 6 times that of a "clean" configuration.
A device for controlling drag on a ground vehicle is presented. The device consists of a porous skin mounted on the trailing surface of the ground vehicle. The porous skin may be separated from the vehicle surface by a distance of at least two times the boundary layer formed on the surface. Alternately, the trailing surface of the ground vehicle may be porous. The device minimizes the strength of the separation in the base and wake regions of the ground vehicle, thus reducing drag.
Despite the extensive experimental and computational data base in the literature on passive porosity, no clear explanation of the governing flow physics exists. It is theorized that the positive porosity concept modifies the external pressure loading by allowing communication between high- and low-pressure regions on the external surface. This study determines the dominant flow phenomena that govern the effectiveness of passive porosity. It aims to assess the contribution of each phenomenon as related to a porous slender axisymmetric forebody. To assess the influence of the mass transfer and pressure equalization phenomena on the effectiveness of passive porosity on slender axisymmetric forebodies, strakes were attached to the 5.0-caliber solid and porous forebodies to force crossflow separation. Longitudinal force and moment data were obtained at a Mach number of 0.1 over an angle-of-attack range of 0 to 55 deg.
Passive device reduces asymmetries in flows and aerodynamic loads. Porous forebody is passive mechanical device, significantly enhancing flight characteristics of all aircraft by minimizing influences of aerodynamics of forebodies upon those characteristics. Leads to safer and better-handling aircraft. Also useful on fast land vehicles and structures or devices subject to high wind.
Quasi-active porous surface used to control pressure loading on aerodynamic surface of aircraft or other vehicle, according to proposal. In transpiration control, one makes small additions of pressure and/or mass to cavity beneath surface of porous skin on aerodynamic surface, thereby affecting rate of transpiration through porous surface. Porous skin located on forebody or any other suitable aerodynamic surface, with cavity just below surface. Device based on concept extremely lightweight, mechanically simple, occupies little volume in vehicle, and extremely adaptable.
Novel scheme developed to contour three-dimensional upper and lower surfaces of wing independently to take maximum advantage of naturally occurring flow and resultant distribution of pressure over broad mach number and lift range. Scheme contours lower and upper surfaces at given cross section to optimize local slopes of upper surface. Sections sheared vertically to create reflexed lower surface. Creates wing nearly flat with mild cumber and minimal twist. Results in design efficient over wide range of lift conditions. Wings for supersonic flight able to provide improved performance at lower speeds without resorting to heavy, complex, and expensive variable-camber devices. Ramifications for both transportation and military systems.
An experimental and theoretical investigation of the effect of the wing planform and bodies on the supersonic aerodynamics of a low-fineness-ratio, multibody configuration has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Force and moment data, flow-visualization data, and surface-pressure data were obtained on eight low-fineness-ratio, twin-body configurations. These configurations varied in inboard wing planform shape, outboard wing planform shape, outboard wing planform size, and presence of the bodies. The force and moment data showed that increasing the ratio of outboard wing area to total wing area or increasing the leading-edge sweep of the inboard wing influenced the aerodynamic characteristics. The flow-visualization data showed a complex flow-field system of shocks, shock-induced separation, and body vortex systems occurring between the side bodies. This flow field was substantially affected by the inboard wing planform shape but minimally affected by the outboard wing planform shape. The flow-visualization and surface-pressure data showed that flow over the outboard wing developed as expected with changes in angle of attack and Mach number and was affected by the leading-edge sweep of the inboard wing and the presence of the bodies. Evaluation of the linear-theory prediction methods revealed their general inability to consistently predict the characteristics of these multibody configurations.
The invention is a natural flow wing and a method for constructing the same. The method comprises contouring a three-dimensional upper surface and a three-dimensional lower surface of the natural flow wing independently of one another into a prescribed shape. Experimental data and theoretical analysis show that flow and pressure-loading over an upper surface of a wing tend to be conical about an apex of the wing, producing favorable and unfavorable regions of performance based on drag. The method reduces these unfavorable regions by shaping the upper surface such that the maximum thickness near a tip of the natural flow wing moves aft, thereby, contouring the wing to coincide more closely with the conical nature of the flow on the upper surface. Nearly constant compressive loading characterizes the flow field over a lower surface of the conventional wing. Magnitude of these compressive pressures on the lower surface depends on angle of attack and on a streamwise curvature of the lower surface of the wing and not on a cross-sectional spanwise curvature. The method, thereby, shapes the lower surface to create an area as large as possible with negative slopes. Any type of swept wing may be used to obtain the final, shaped geometry of the upper and lower surfaces of the natural flow wing.
A wing-design study was conducted on a 65 degree swept leading-edge delta wing in which the wing geometry was modified to take advantage of the naturally occurring flow that forms over a slender wing in a supersonic flow field. Three-dimensional nonlinear analysis methods were used in the study which was divided into three parts: preliminary design, initial design, and final design. In the preliminary design, the wing planform, the design conditions, and the near-conical wing-design concept were derived, and a baseline standard wing (conventional airfoil distribution) and a baseline near-conical wing were chosen. During the initial analysis, a full-potential flow solver was employed to determine the aerodynamic characteristics of the baseline standard delta wing and to investigate modifications to the airfoil thickness, leading-edge radius, airfoil maximum-thickness position, and wing upper to lower surface asymmetry on the baseline near-conical wing. The final design employed an Euler solver to analyze the best wing configurations found in the initial design and to extend the study of wing asymmetry to develop a more refined wing. Benefits resulting from each modification are discussed, and a final 'natural flow' wing geometry was designed that provides an improvement in aerodynamic performance compared with that of a baseline conventional uncambered wing, linear-theory cambered wing, and near-conical wing.
An experimental investigation to determine the effectiveness of porosity for alleviating side forces on forebodies was conducted in the NASA Langley Research Center 7 x 10 ft High-Speed Wind Tunnel. The study consisted of a comparison of experimental force, moment, and surface pressure results obtained on a fineness ratio 5.0 tangent-ogive porous forebody with 0.020 in. hole diameter and 22 percent porosity with results obtained on a solid forebody. The forebodies were tested with cylindrical afterbodies. The solid forebody was tested with transition grit to simulate fully turbulent conditions and without transition grit to simulate free transition conditions. The extent of porosity on the forebody was varied to determine the extent of porosity needed to alleviate side forces. Static longitudinal and lateral-directional stability and surface pressure data were obtained at Mach numbers of 0.2, 0.5, and 0.8. The angle of attack range was from 5 to 45 deg and roll angles from -90 to 180 deg. The solid forebody exhibited large asymmetries at moderate to high angles of attack causing large side forces and yawing moments. The porous forebody exhibited no significant side forces or yawing moments at any angle of attack tested.
Subsonic wind tunnel tests were performed on solid and porous (22 percent) 5.0-caliber forebody models to assess the effect of free and fixed cross-flow separation on the effectiveness of passive porosity. The effectiveness of passive porosity to control the local pressure loading for forced cross-flow separation is found to be similar to that observed for the free cross-flow separation condition. It is also found that the effectiveness of passive porosity is significantly enhanced in the presence of large positive pressures on the porous surface.
Explore the source record for details and available documents.
A device is provided for controlling pressure loading of a member caused by a fluid moving past the member or the member moving through a fluid. The device consists of a porous skin mounted over the solid surface of the member and separated from the solid surface by a plenum. Fluid from an area exerting high pressure on the member may enter the plenum through the porous surface and exit into an area exerting a lower pressure on the member, thus controlling pressure loading of the member.