Engineering Papers⌕ Search

Engineering topics

Barnwell, R. W.

Publications and source records attributed to Barnwell, R. W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Natural laminar flow and laminar flow control

The present volume discusses the development history and basic concepts of laminar flow control, laminar flow flight experiments, subsonic laminar-flow airfoils, and a design philosophy for long-range laminar flow-control commercial transports with advanced supercritical airfoils. Also discussed are the relationship of wave-interaction theory to laminar flow control, supersonic laminar flow control, and the NASA-Langley 8-ft Transonic Pressure Tunnel.

Barnwell, R. W.↗
NASA NTRS1987

A finite-difference outer layer and integral inner layer method for the solution of the turbulent boundary layer equations

A new turbulent boundary-layer method is developed which models the inner region with the law of the wall while the outer region uses Clauser's eddy viscosity in Matsuno's finite-difference method. The match point between the inner and outer regions as well as the wall shear stress are determined at each marching step during the computation. Results obtained for incompressible, two-dimensional flow over flat plates and ellipses are compared with solutions from a baseline method which uses a finite-difference method for the entire boundary layer. Since the present method used the finite-difference method in the outer region only, the number of grid points required was about half that needed for the baseline method. Accurate displacement and momentum thicknesses were predicted for all cases. Skin friction was predicted well for the flat plate, but the accuracy decreased significantly for the ellipses. Adding a wake functions to the law of the wall allows some of the pressure gradient effect to be taken into account thereby increasing the accuracy of the method.

Barnwell, R. W.↗
NASA NTRS1986

Optimum transonic wind tunnel

The optimum facility to complement existing high Reynolds number transonic wind tunnels is discussed. It is proposed that the facility be cryogenic, have a total pressure of five atmospheres or less, and have a test section on the order of 4- to 5-meters square. The large size is to accommodate complicated models such as those used in propulsion testing. It is suggested that magnetic suspension and wall interference minimization and correction procedures be used. Simplicity of initial design is stressed as a means of providing for future growth opportunities.

Barnwell, R. W.↗
NASA NTRS1984

Effect of sidewall suction on flow in two-dimensional wind tunnels

A closed-form analysis of flow in a two-dimensional subsonic wind tunnel which uses sidewall suction around the model to reduce sidewall boundary-layer effects is presented. The model problem which is treated involves a flat plate airfoil in a tunnel with a suction window shaped to permit an analytic solution. This solution shows that the lift coefficient depends explicitly on the porosity parameter of the suction window and implicitly on the suction pressure differential. For a given sidewall displacement thickness, the lift coefficient increases as the suction-window porosity decreases.

Barnwell, R. W.↗
NASA NTRS1984

Effect of boundary layers on solid walls in three-dimensional subsonic wind tunnels

A solution for the tunnel wall boundary layer effects for three-dimensional subsonic tunnels is presented. The model potentials are represented with simple singularities placed on the centerline of the tunnel and Laplace's equation in cylindrical coordinates is solved for either the conventional homogeneous slotted-wall boundary condition, the solid-wall viscous boundary condition, or a combination of them. The most pronounced wall boundary layer effect is on solid blockage for completely closed wind tunnels. Boundary layers on the wall reduce the blockage from the solid-wall, no-boundary-layer case in a manner similar to opening slots in a solid wall. Additionally, for solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, whereas the lift interference factor at the model station does not depend on the boundary layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.

Adcock, J. B.↗
NASA NTRS1983

Effect of boundary layers on solid walls in three-dimensional subsonic wind tunnels

A linear method is developed which accounts for the effects of boundary layers on solid walls in subsonic three-dimensional wind tunnels. The streamwise gradient of the displacement thickness for a solid-wall boundary layer is expressed in terms of the von Karman momentum integral. The growth of the boundary layer due to the wall shearing stress is small compared to the variation caused by the model-induced pressure gradient. The viscous boundary condition can be expressed in terms of the edge velocity gradient and the gradient of the inviscid velocity potential function at the wall. Utilizing this analysis on the solid walls of several three-dimensional wind tunnel configurations shows that the most pronounced wall boundary-layer effect is on solid blockage for completely closed wind tunnels. For solid-wall tunnel configurations, the streamline curvature interference factor is reduced by a significant amount, while the lift interference factor at the model station does not depend on the boundary-layer parameter. For combination wall configurations, the slot effect of the horizontal walls dominates the viscous effect of the solid sidewalls.

Adcock, J. B.↗
NASA NTRS1982

Similarity rules for effects of sidewall boundary layer in two-dimensional wind tunnels

A simple analysis of the interaction of the model pressure field with the boundary layer on an unventilated wind tunnel wall is presented. It is shown that the effects of this interaction are similar to compressibility effects for sidewall boundary layers in two dimensional wind tunnels. This similarity is used to derive modified forms of the Prandtl Glauert rule for subsonic flow and the von Karman rule for transonic flow which are validated by comparison with experimental data. The three dimensional interaction problem is discussed, and it is shown that model pressure field/wall boundary layer interaction effects are not similar to compressibility effects in three dimensional wind tunnels.

Barnwell, R. W.↗
NASA NTRS1982

The simulation of time varying ascent loads on arrays of Shuttle tiles in a large transonic tunnel

A large variety of tests were made to determine the strength, fatigue and thermal characteristics of the thermal-protection system of the Shuttle orbiter. The present paper describes first-launch-critical tests which were conducted in the Langley 8-Foot Transonic Pressure Tunnel (8'TPT) which simulated the time histories of Shuttle ascent loads on tile arrays bonded to structures which accurately duplicated those of the Shuttle. The time varying free-stream conditions were provided by controlling the deflection angle history of diffuser spoiler flaps in an automated way. Time histories of the critical-load parameters imposed on the tile arrays in the tunnel are compared in the paper to those expected in flight. In addition, the effect of repeated load pulses on the smoothness of the surface and condition of the tiles is discussed briefly.

Bobbitt, P. J.↗
NASA NTRS1981

A potential-flow/boundary-layer method for calculating subsonic and transonic airfoil flow with trailing-edge separation

The development of a potential-flow/boundary-layer method for calculating subsonic and transonic turbulent flow past airfoils with trailing-edge separation is reported. A moment-of-momentum integral boundary-layer method is used which employs the law-of-the-wall/law-of-the-wake velocity profile and a two-layer eddy-viscosity model and ignores the laminar sublayer. All integrals across the boundary layer are obtained in closed form. Separation is assumed to occur when the shearing-stress velocity vanishes. A closed-form solution is derived for separated-flow regions where the shearing stress is negligible. In the potential-flow method, the exact form of the airfoil boundary condition is used, but it is applied at the chord line rather than the airfoil surface. This allows the accurate computation of flow about airfoils at large angles of attack but permits the use of body-oriented Cartesian computational grids. The governing equation for the perturbation velocity potential contains several terms in addition to the classical small-disturbance terms.

Barnwell, R. W.↗
NASA NTRS1979

Design and calibration of slotted walls for transonic airfoil wind tunnels

The traditional procedure for estimating the performance of slotted walls for airfoil wind tunnels is reviewed, and a modification which improves the accuracy of this procedure is described. Unlike the traditional procedure, the modified procedure indicates that the design of airfoil wind-tunnel walls which induce minimal blockage and streamline-curvature effects is feasible. The design and testing of such a slotted wall is described. It is shown experimentally that the presence of a model can affect the plenum pressure and thus make the use of the plenum pressure as a calibration reference questionable. Finally, an ONERA experiment which shows the effect of the sidewall boundary layer on the measured model normal force is discussed.

Barnwell, R. W.↗
NASA NTRS1979

A similarity rule for compressibility and sidewall-boundary-layer effects in two-dimensional wind tunnels

The effect of the sidewall boundary layer on flow in two-dimensional wind tunnels is determined. The small-disturbance and isentropic approximations are made, and the sidewall-boundary-layer dynamics are modeled with the von Karman momentum-integral equation. The effects of the edge-velocity-gradient term in the sidewall momentum integral, which is usually dominant near the model, and the compressibility term are shown to be similar. It is shown that the effect of sidewall suction around the model is not similar to two-dimensional flow. Comparisons with experiment are made to verify the similarity rule.

Barnwell, R. W.↗
NASA NTRS1978

Low-speed aerodynamic characteristics of a 16-percent-thick variable-geometry airfoil designed for general aviation applications

Tests were conducted in the Langley low-turbulence pressure tunnel to determine the aerodynamic characteristics of climb, cruise, and landing configurations. These tests were conducted over a Mach number range from 0.10 to 0.35, a chord Reynolds number range from 2.0 x 1 million to 20.0 x 1 million, and an angle-of-attack range from -8 deg to 20 deg. Results show that the maximum section lift coefficients increased in the Reynolds number range from 2.0 x 1 million to 9.0 x 1 million and reached values of approximately 2.1, 1.8, and 1.5 for the landing, climb, and cruise configurations, respectively. Stall characteristics, although of the trailing-edge type, were abrupt. The section lift-drag ratio of the climb configuration with fixed transition near the leading edge was about 78 at a lift coefficient of 0.9, a Mach number of 0.15, and a Reynolds number of 4.0 x 1 million. Design lift coefficients of 0.9 and 0.4 for the climb and cruise configurations were obtained at the same angle of attack, about 6 deg, as intended. Good agreement was obtained between experimental results and the predictions of a viscous, attached-flow theoretical method.

Barnwell, R. W.↗
NASA NTRS1978

Design and Performance Evaluation of Slotted Walls for Two-Dimensional Wind Tunnels

A procedure for designing slotted walls for two dimensional wind tunnels is is presented. The design objective is the minimization of blockage of streamline curvature or the reduction of both. The slotted wall boundary condition is derived both for flow from the tunnel into the plenum and vice versa, and the procedure for evaluating wall interference is described. A correlation of experimental data for the slotted wall boundary condition is given. Results are given for several designs and evaluations of slotted wind tunnel walls.

Barnwell, R. W.↗
NASA NTRS1978

A parametric experimental study of the interference effects and the boundary-condition coefficient of slotted wind-tunnel walls

An experimental study of slotted upper and lower walls in a two-dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data are pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary-condition coefficient, which relates the pressure and streamline curvature near the wall, is determined from the wall pressure measurements. The measured wall-induced interference is correlated with the experimental values for the boundary-condition coefficient. This correlation is compared with theory.

Everhart, J. L.↗
NASA NTRS1978

A parametric experimental study of the slotted-wall boundary condition

An experimental study of slotted upper and lower walls in a two dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data were pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary condition coefficient, which related the pressure and streamline curvature near the wall, was determined from the wall pressure measurements. The measured wall-induced interference was correlated with the experimental values for the boundary condition coefficient. This correlation was compared with theory.

Everhart, J. L.↗
NASA NTRS1976

Two inviscid computational simulations of separated flow about airfoils

Two inviscid computational simulations of separated flow about airfoils are described. The basic computational method is the line relaxation finite-difference method. Viscous separation is approximated with inviscid free-streamline separation. The point of separation is specified, and the pressure in the separation region is calculated. In the first simulation, the empiricism of constant pressure in the separation region is employed. This empiricism is easier to implement with the present method than with singularity methods. In the second simulation, acoustic theory is used to determine the pressure in the separation region. The results of both simulations are compared with experiment.

Barnwell, R. W.↗