Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “zinc oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Robust passivation of CdSeTe based solar cells using reactively sputtered magnesium zinc oxide

Magnesium zinc oxide (MZO, Mg x Zn 1-x O) is a leading emitter for CdTe-based solar cells due to its transparency and the ability to tune its conduction band offset with the absorber. Devices employing alloyed cadmium selenide telluride (CST, CdSe y Te 1-y ) absorbers achieved high efficiency (>19%) using MZO deposited by reactive sputtering over a broad composition range (3.68–3.92 eV, x: 0.20–0.35). Minimal differences in implied and measured open circuit voltage indicate that the contacts are well passivated and highly selective across the spectrum of MZO employed. Device performance insensitivity to MZO composition, which is not observed in CdTe devices, is attributed to the formation of an oxygenated interface layer. Se volatility creates a group VI deficiency at the interface that drives O migration from the MZO into the absorber. This introduces conductivity in the emitter not present in its as-deposited state, contributing to the exceptional performance observed. It is shown that the quality of device passivation depends on the oxidation state of the as-deposited MZO such that intelligent control and management of the reactive sputtering process is required.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Entrapped Molecule‐Like Europium‐Oxide Clusters in Zinc Oxide with Nearly Unaffected Host Structure

Abstract Nanocrystalline ZnO sponges doped with 5 mol% EuO 1.5 are obtained by heating metal–salt complex based precursor pastes at 200–900 °C for 3 min. X‐ray diffraction, transmission electron microscopy, and extended X‐ray absorption fine structure (EXAFS) show that phase separation into ZnO:Eu and c ‐Eu 2 O 3 takes place upon heating at 700 °C or higher. The unit cell of the clean oxide made at 600 °C shows only ≈0.4% volume increase versus undoped ZnO, and EXAFS shows a ZnO local structure that is little affected by the Eu‐doping and an average Eu 3+ ion coordination number of ≈5.2. Comparisons of 23 density functional theory‐generated structures having differently sized Eu‐oxide clusters embedded in ZnO identify three structures with four or eight Eu atoms as the most energetically favorable. These clusters exhibit the smallest volume increase compared to undoped ZnO and Eu coordination numbers of 5.2–5.5, all in excellent agreement with experimental data. ZnO defect states are crucial for efficient Eu 3+ excitation, while c ‐Eu 2 O 3 phase separation results in loss of the characteristic Eu 3+ photoluminescence. The formation of molecule‐like Eu‐oxide clusters, entrapped in ZnO, proposed here, may help in understanding the nature of the unexpected high doping levels of lanthanide ions in ZnO that occur virtually without significant change in ZnO unit cell dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Zinc oxide based sorbent and process for preparing same

Zinc oxide-based sorbents, and processes for preparing and using them are provided, wherein the sorbents are preferably used to remove one or more reduced sulfur species from gas streams. The sorbents contain an active zinc component, optionally in combination with one or more promoter components and/or one or more substantially inert components. The active zinc component is a two-phase material, consisting essentially of a zinc oxide (ZnO) phase and a zinc aluminate (ZnAl 2 O 4 ) phase. Each of the two phases is characterized by a relatively small crystallite size of typically less than about 50 nm (500 Angstroms). Preferably the sorbents are prepared by using an alkali metal base to convert a precursor mixture, containing a precipitated zinc oxide precursor and a precipitated aluminum oxide precursor, to the two-phase, active zinc oxide containing component, with the resulting sorbent having a sodium level within a desired range.

Shen, Jian-Ping↗
DOE OSTI2025

Fabrication of nanoporous doped metal oxide coatings via selective infiltration of a block copolymer template: The case of Al-doped zinc oxide

Conductive nanoporous conformal coatings are important for various applications including touchscreens, displays, and electrochromic windows, though design of such coating with controlled porosity and composition remains challenging. We propose a sequential infiltration synthesis (SIS) method for the fabrication of nanoporous conductive aluminum-doped zinc oxide (AZO) films by infiltrating block copolymer (BCP) templates, specifically polystyrene-block-polyvinyl pyridine (PS-b-P4VP), with diethyl zinc and trimethyl aluminum precursors. Tunability of both porosity and electrical conductivity is achieved by precisely controlling the swelling behavior of the polymer templates and adjusting the number of SIS cycles. Further, our results reveal that porosity levels can reach up to 80 %, with resistivity as low as ~7.83 Ωcm. Using conductive atomic force microscopy (C-AFM) and Hall effect measurements, we show that lower concentrations of aluminum doping relative to zinc (around 1: 17) results in higher conductivity of the AZO films. Additionally, AZO is based on zinc oxide (ZnO) which is cost-efficient, abundant and less toxic than commonly used transparent conductive oxides such as indium tin oxide (ITO) and fluorine-doped tin oxide (FTO). Therefore, this novel approach opens new possibilities for creating highly porous, conformal, conductive AZO coatings with customizable porosity and composition, making them ideal candidates for diverse optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Gallium-doped zinc oxide: nonlinear reflection and transmission measurements and modeling in the ENZ region

Abstract Strong nonlinear materials have been sought after for decades for applications in telecommunications, sensing, and quantum optics. Gallium-doped zinc oxide is a II–VI transparent conducting oxide that shows promising nonlinearities similar to indium tin oxide and aluminum-doped zinc oxide for the telecommunications band. Here we explore its nonlinearities in the epsilon near zero (ENZ) region and show n 2,eff values on the order of 4.5 × 10 −3 cm 2 GW −1 for IR pumping on 200–300 nm thin films. Measuring nonlinear changes in transmission and reflection with a white light source probe in the near-IR while exciting in the near-IR provides data in both time and wavelength. Three films varying in thickness, optical loss, and ENZ crossover wavelength are numerically modeled and compared to experimental data showing agreement for both dispersion and temporal relaxation. In addition, we discuss optimal excitation and probing wavelengths occur around ENZ for thick films but are red-shifted for thin films where our model provides an additional degree of freedom to explore. Obtaining accurate nonlinear measurements is a difficult and time-consuming task where our method in this paper provides experimental and modeled data to the community for an ENZ material of interest.

Ball, Adam (ORCID:0000000318167813)↗
DOE OSTI2020

Extraordinarily large permittivity modulation in zinc oxide for dynamic nanophotonics

The dielectric permittivity of a material encapsulates the essential physics of light-matter interaction into the material's local response to optical excitation. Photo-induced modulation of the permittivity can enable an unprecedented level of control over the phase, amplitude, and polarization of light. Therefore, the detailed dynamic characterization of technology-relevant materials with substantially tunable optical properties and fast response times is a crucial step to realize tunable optical devices. This work reports on the extraordinarily large permittivity changes in zinc oxide thin films (up to similar to 3.6 relative change in the real part of the dielectric permittivity at 1600 nm wavelength) induced by optically generated free carriers. We demonstrate broadband reflectance modulation up to 70% in metal-backed oxide mirrors at the telecommunication wavelengths, with picosecond-scale relaxation times. The epsilon near zero points of the films can be dynamically shifted from 8.5 mm to 1.6 mm by controlling the pump fluence. Additionally, the modulation can be selectively enhanced at specific wavelengths employing metal-backed zinc oxide disks while maintaining picosecond-scale switching times. This work provides insights into the free-carrier assisted permittivity modulation in zinc oxide and could enable the realization of novel dynamic devices for beam-steering, polarizers, and spatial light modulators.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Accessibility and Mechanical Stability of Nanoporous Zinc Oxide and Aluminum Oxide Coatings Synthesized via Infiltration of Polymer Templates

The conformal nanoporous inorganic coatings with accessible pores that are stable under applied thermal and mechanical stresses represent an important class of materials used in the design of sensors, optical coatings, and biomedical systems. Here, we synthesize porous AlO x and ZnO coatings by the sequential infiltration synthesis (SIS) of two types of polymers that enable the design of porous conformal coatings—polymers of intrinsic microporosity (PIM) and block co-polymer (BCP) templates. Using quartz crystal microbalance (QCM), we show that alumina precursors infiltrate both polymer templates four times more efficiently than zinc oxide precursors. Using the quartz crystal microbalance (QCM) technique, we provide a comprehensive study on the room temperature accessibility to water and ethanol of pores in block copolymers (BCPs) and porous polymer templates using polystyrene-block-poly-4-vinyl pyridine (PS75-b-P4VP25) and polymers of intrinsic microporosity (PIM-1), polymer templates modified by swelling, and porous inorganic coatings such as AlO x and ZnO synthesized by SIS using such templates. Importantly, we demonstrate that no structural damage occurs in inorganic nanoporous AlO x and ZnO coatings synthesized via infiltration of the polymer templates during the water freezing/melting cycling tests, suggesting excellent mechanical stability of the coatings, even though the hardness of the inorganic nanoporous coating is affected by the polymer and precursor selections. We show that the hardness of the coatings is further improved by their annealing at 900 °C for 1 h, though for all the cases except ZnO obtained using the BCP template, this annealing has a negligible effect on the porosity of the material, as is confirmed by the consistency in the optical characteristics. These findings unravel new potential for the materials being used across various environment and temperature conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Zinc Oxide–Graphene Nanocomposite-Based Sensor for the Electrochemical Determination of Cetirizine

A nanocomposite electrode of graphene (Gr) and zinc oxide (ZnO) nanoparticles was fabricated to study the electrochemical oxidation behavior of an anti-inflammatory drug, i.e., cetirizine (CET). The voltametric response of CET for bare CPE, Gr/CPE, ZnO/CPE, and the ZnO-Gr nanocomposite electrode was studied. The modifier materials were characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray powder diffraction (XRD) to comprehend the surface morphology of the utilized modifiers. The influence of pH, scan rate, and accumulation time on the electrooxidation of CET was examined. It was found that the electrochemical oxidation of CET was diffusion-controlled, in which two protons and two electrons participated. The detection limit was found to be 2.8 × 10 -8 M in a linearity range of 0.05–4.0 µM. Study of excipients was also performed, and it was found that they had negligible interference with the peak potential of CET. The validation and utility of the fabricated nanocomposite sensor material were examined by analyzing clinical and biological samples. Stability testing of the nanocomposite electrode was conducted to assess the reproducibility, determining that the developed biosensor has good stability and high efficiency in producing reproducible results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Impact of cobalt doping on structural and magnetic properties of zinc oxide nanocomposites synthesized by mechanical ball-milling method

A series of zinc oxide (ZnO) semiconductor nanocomposite samples doped with different concentrations of cobalt (Co) were successfully synthesized via simple and highly effective mechanical ball-milling method using suitable precursors. All doped nanocomposites crystallized in hexagonal wurtzite formation of ZnO. No alteration in the wurtzite structure, with no evidence of any segregated secondary phase(s) was detected with increasing doping concentrations. This result unambiguously verified the substitution of Zn 2+ sites by Co 2+ ions in the ZnO host lattice for different doping concentrations. Moreover, room temperature ferromagnetic behavior was observed in all doped nanocomposite samples in the reported work. Present study clearly shows that mechanical ball-milling is a facile, inexpensive, eco-friendly method to synthesize crystalline and magnetic Co doped ZnO nanocomposites for next generation spin-based devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Stable magnesium zinc oxide by reactive Co-Sputtering for CdTe-based solar cells

Magnesium zinc oxide (MZO) is a promising front contact material for CdTe solar cells. Due to its higher band gap than traditional CdS, MZO can reduce parasitic absorption to significantly increase short-circuit current density while also providing a benefit of conduction band offset tuning through Mg:Zn ratio optimization. MZO has been successfully implemented into CdTe devices, however its stability has been of concern. The MZO stability issue has been attributed to the presence of oxygen in the CdTe device processing ambient, leading to double-diode behavior (S-kink) in the current density-voltage curves. Here we report on MZO thin films deposited by reactive co-sputtering. The reactively co-sputtered MZO thin films have encouraging stability, show no significant variation in work function of the surface over a period of 6 months, as measured by Kelvin probe. Energy conversion efficiencies of around 16% have been achieved both with and without presence of oxygen in device processing ambients across multiple research facilities. Finally, these efficiencies should be possible to increase further by tuning of the thin film deposition and device processing parameters, especially through optimization of the back contact.

14 SOLAR ENERGY↗
DOE OSTI2024

Effect of Solvent Composition on Non-DLVO Forces and Oriented Attachment of Zinc Oxide Nanoparticles

Oriented attachment (OA) occurs when nanoparticles in solution align their crystallographic axes prior to colliding and subsequently fuse into single crystals. Traditional colloidal theories such as DLVO provide a framework for evaluating OA but fail to capture key particle interactions due to the atomistic details of both the crystal structure and the interfacial solution structure. Using zinc oxide as a model system, we investigated the effect of the solvent on short-ranged and long-ranged particle interactions and the resulting OA mechanism. In situ TEM imaging showed that ZnO nanocrystals in toluene undergo long-range attraction comparable to 1kT at separations of 10 nm and 3kT near particle contact. These observations were rationalized by considering non-DLVO interactions, namely dipole-dipole forces and torques between the polar ZnO nanocrystals. Langevin dynamics simulations showed stronger interactions in toluene compared to methanol solvents, consistent with the experimental results. Concurrently, we performed atomic force microscopy measurements using ZnO-coated probes for the short-ranged interaction. Our data provided valuable insights into another type of non-DLVO interaction, namely the repulsive solvation force. Specifically, the solvation force was stronger in water compared to ethanol and methanol, due to the stronger hydrogen bonding and denser packing of water molecules at the interface. In conclusion, our results highlight the importance of non-DLVO forces in a general framework for understanding and predicting particle aggregation and attachment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effect of proton irradiation temperature on persistent photoconductivity in zinc oxide metal-semiconductor-metal ultraviolet photodetectors

The electrical and structural characteristics of 50-nm-thick zinc oxide (ZnO) metal-semiconductor-metal ultraviolet (UV) photodetectors subjected to proton irradiation at different temperatures are reported and compared. The devices were irradiated with 200 keV protons to a fluence of 1016 cm−2. Examination of the x-ray diffraction (XRD) rocking curves indicates a preferred (100) orientation prior to irradiation, with decrease in crystal quality afterward. Additionally, peak shifts in XRD and Raman spectra of the control sample relative to well-known theoretical positions are indicative of tensile strain in the as-deposited ZnO films. Shifts toward theoretical unstrained positions are observed in the irradiated films, which indicates partial relaxation. Raman spectra also indicate increase in oxygen vacancies (VO) and zinc interstitial defects (Zni) compared to the control sample. Additionally, transient photocurrent measurements performed on each sample at different temperatures showed up to 2× increase in photocurrent decay time constants for irradiated samples vs the control. This persistent photoconductive behavior is linked to the activation of electron and hole traps near the surface, and to the desorption and reabsorption of O2 molecules on the ZnO surface under the influence of UV light. Using an Arrhenius model, trap activation energies were extracted and, by comparing with known energies from the literature, the dominant defects contributing to persistent photoconductivity for each irradiation condition were identified. The persistence of differences in photocurrent transients between different samples months after irradiation indicates that the defects introduced by the suppression of thermally activated dynamic annealing processes have a long-term deleterious effect on device performance.

Heuser, Thomas A. (ORCID:0000000225642400)↗
DOE OSTI2024

Identifying biochemical constituents involved in the mycosynthesis of zinc oxide nanoparticles

Filamentous fungi are known to secrete biochemicals that drive the synthesis of nanoparticles (NPs) that vary in composition, size, and shape; a process deemed mycosynthesis. Following the introduction of precursor salts directly to the fungal mycelia or their exudates, mycosynthesis proceeds at ambient temperature and pressure, and near neutral pH, presenting significant energy and cost savings over traditional chemical or physical approaches. The mycosynthesis of zinc oxide (ZnO) NPs by various fungi exhibited a species dependent morphological preference for the resulting NPs, suggesting that key differences in the biochemical makeup of their individual exudates may regulate the controlled nucleation and growth of these different morphologies. Metabolomics and proteomics of the various fungal exudates suggest that metal chelators, such as hexamethylenetetramine, present in high concentrations in exudates of Aspergillus versicolor are critical for the production dense, well-formed, spheroid nanoparticles. Further, the results also corroborate that the proteinaceous material in the production of ZnO NPs serves as a surface modifier, or protein corona, preventing excessive coagulation of the NPs. Collectively, these findings suggest that NP morphology is regulated by the small molecule metabolites, and not proteins, present in fungal exudates, establishing a deeper understanding of the factors and mechanism underlying mycosynthesis of NPs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Mycosynthesis of Zinc Oxide Nanoparticles Exhibits Fungal Species Dependent Morphological Preference

Filamentous fungi can synthesize a variety of nanoparticles (NPs), a process referred to as mycosynthesis that requires little energy input, do not require the use of harsh chemicals, occurs at near neutral pH, and do not produce toxic byproducts. While NP synthesis involves reactions between metal ions and exudates produced by the fungi, the chemical and biochemical parameters underlying this process remain poorly understood. Here, the role of fungal species and precursor salt on the mycosynthesis of zinc oxide (ZnO) NPs is investigated. This data demonstrates that all five fungal species tested are able to produce ZnO structures that can be morphologically classified into i) well-defined NPs, ii) coalesced/dissolving NPs, and iii) micron-sized square plates. Further, species-dependent preferences for these morphologies are observed, suggesting potential differences in the profile or concentration of the biochemical constituents in their individual exudates. This data also demonstrates that mycosynthesis of ZnO NPs is independent of the anion species, with nitrate, sulfate, and chloride showing no effect on NP production. Finally, these results enhance the understanding of factors controlling the mycosynthesis of ceramic NPs, supporting future studies that can enable control over the physical and chemical properties of NPs formed through this “green” synthesis method.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Thermomechanical properties of stereolithographic 3D-printed zinc oxide nanocomposites

Stereolithography (SLA) is a highly versatile additive manufacturing technique that utilizes various ink formulations to fabricate 3D-printed nanocomposite structures with desired properties. Zinc oxide (ZnO) is a promising candidate due to its excellent mechanical and thermal stability, and compatibility with various polymeric matrices. Here, in this work, varying ink formulations containing ZnO nanoparticles, along with employing appropriate post-printing curing parameters to fabricate SLA 3D-printed acrylate-based nanocomposites with improved mechanical and thermal properties, were reported. This study can significantly contribute to expanding its potential use in practical applications such as biomedical and structural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electro-Optical Stability in Gallium Magnesium Zinc Oxide Layers for CdTe Solar Cells

In CdTe solar cells, the emitter electron density, bandgap, and band alignment can be tuned by adjusting alloy composition and stoichiometry in gallium magnesium zinc oxide (GMZO) layers, thereby allowing for critical front interface engineering. For example, computational modeling indicates efficiency can change from 7% to 25% by adjusting these buffer properties even with fixed CdSeTe and CdTe material properties. However, the GMZO as-deposited electro-optical properties can shift during subsequent CdTe deposition, CdCl 2 annealing, and solar cell operation. Here, we examine these changes by sputtering GMZO films on glass, and measuring the electron density before and after post-deposition treatments over a range of temperatures and different ambients. We then compare GMZO to SnO 2 and MZO. The addition of Ga to MgZnO is found to have profound effects on both the electron density and electro-optical stability that should be advantageous for CdTe solar cells.

41 EE - Solar Energy Technologies Office (EE-4S)↗