SEARCH · Engineering Papers

Results for “wide angle scans”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

3D Printing ofThermally Responsive Shape Memory LiquidCrystalline Epoxy Networks

Abstract A two-component liquid crystalline epoxy network (LCEN) with shape memory behavior was developed and evaluated as a candidate material for 3D printing. The cure kinetics of the uncured material and the shape memory properties of the cured LCEN were investigated by using parallel plate rheology and dynamic mechanical analysis, respectively. A commercially available fumed silica additive was introduced to the neat, uncured material to improve the rheological properties for 3D printing. The addition of fumed silica was found to increase the yield stress, shear-thinning behavior, and toughness of the uncured epoxy ink. Polarized light microscopy, differential scanning calorimetry, and wide-angle X-ray scattering measurements between the neat and additive-modified LCEN suggested a reduction in liquid crystalline alignment in the modified LCEN, owing to interactions between crystalline domains and fumed silica, which in turn influenced the mechanical behavior. Overall, the additive was found to be successful in preserving the shape memory properties of LCEN while improving its printability.

Chemistry↗

DOE OSTI2024

Correlation of Processing and Structure in an Ethylene‐Glycol Side‐Chain Modified Polythiophene via Combined X‐Ray Scattering and 4D Scanning Transmission Electron Microscopy

The results of a combined grazing incidence wide-angle X-ray scattering (GIWAXS) and 4D scanning transmission microscopy (4D-STEM) analysis of the effects of thermal processing on poly(3[2-(2-methoxyethoxy)ethoxy]-methylthiophene-2,5-diyl) are reported, a conjugated semiconducting polymer used as the active layer in organic electrochemical transistor devices. GIWAXS provides a measure of overall crystallinity in the film, while 4D-STEM produces real-space maps of the morphology and orientation of individual crystallites along with their spatial extent and distribution. The sensitivity of the 4D-STEM detector allows for collection of electron diffraction patterns at each position in an image scan while limiting the imparted electron dose to below the damage threshold. In conclusion, the effects of heat treatment on the distribution and type of crystallites present in the films is determined.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Revisiting the Anisotropic Complex Refractive Indices of Sodium Nitrate for Interpretation of the Reflectance Spectrum of Pressed Pellets

Reflectance spectroscopy is notoriously confounding in that the measured spectral response is highly dependent upon the morphology of the sample. Fortunately, all such perturbations are neatly encoded by the complex refractive index of the sample. Herein, we seek to quantitatively model the measured infrared reflectance spectrum of a specularly flat pressed pellet sample of the birefringent compound, sodium nitrate. Single crystals of sodium nitrate were synthesized via a slow evaporation process and spectroscopically analyzed using polarization-dependent infrared single-angle reflectance spectroscopy. The anisotropic complex refractive index was measured from 7500 to 300 cm-1 (1.33 to 33.33 µm). The deduced anisotropic optical constants were found to be consistent with those previously reported. Once measured and validated, the optical constants were applied to model the pressed pellet reflectance spectrum. It was evident that an average of the anisotropic refractive indices was insufficient to account for the measured pellet reflectance. In order to account for contributions of all possible microcrystalline orientations within the pellet, the Python package PYELLI was used to calculate a basis set of orientation-dependent reflection spectra spanning the distinct ? and ? Euler rotations of the uniaxial crystal. When the population of orientations was allowed to vary freely in a spectral fit analysis, the fit-deduced orientations were tightly clustered along f = 45º, hinting at residual anisotropy in the pressed pellet sample. Conversely, an equally valid spectral fit (with marginally worse fit metric) was obtained when the population was constrained to an isotropic distribution of orientations. Subsequent non-zero cross-polarization reflectance measurements likewise suggested anisotropy in the pellet. However, both grazing incidence wide-angle x-ray scattering and scanning electron microscopy measurements revealed that the microcrystal orientations at the surface of the pressed pellet sample were isotropically distributed (and that the average crystallite size was larger than ?/10). Application of the measured complex refractive indices for modeling the reflectance spectrum of the pressed pellet, and rectification of these seemingly contradictory observations will be discussed.

Wilhelm, Michael J.↗

DOE OSTI2026

Effects of Polymer Morphology on Solvent and Catalyst Accessibility during Polyethylene and Polystyrene Autoxidation

Efficient catalytic deconstruction of plastics requires facile solvent and catalyst access to polymer substrates to minimize mass transfer effects. Autoxidation using Co(II) acetate, Mn(II) acetate, and a radical carrier in acetic acid is a promising strategy to deconstruct mixed plastic waste, yet the role of polymer morphology in governing solvent and catalyst accessibility remains poorly understood. Here, in situ simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS), complemented by X-ray fluorescence (XRF) imaging and high-pressure differential scanning calorimetry (DSC), were used to elucidate interactions between acetic acid, a Co/Mn catalyst solution, and semicrystalline polyethylene (PE) and amorphous polystyrene (PS) from room temperature to 160 °C. In PE, acetic acid and catalyst access were confined to amorphous regions and cryomilled particle interfaces at room temperature, while crystalline lamellae remained intact after soaking for up to 34 h. Increasing temperature enabled solvent uptake into PE, followed by solvent-assisted softening above 100 °C, and a modest melting-point depression that removed lamellar transport barriers upon melting. Conversely for PS, acetic acid penetrated the glassy polymer without inducing chain mobility until the glass transition was reached, above which the observed structural changes were consistent with enhanced segmental mobility which enabled bulk penetration. These results suggest that polymer morphology and thermally activated physical transitions arising from diffusion and polymer–solvent interactions can influence whether autoxidation of plastics is transport-limited or kinetically controlled, providing a framework for aligning reaction conditions with reaction outcomes.

09 BIOMASS FUELS↗

DOE OSTI2025

Crystallization Mechanisms of Poly(vinylidene Fluoride- co -chlorotrifluoroethylene): Nucleation Transitions, Growth Kinetics, and Microstructure Evolution

The crystallization kinetics of FK-800, a commercial semicrystalline copolymer of chlorotrifluoroethylene and vinylidene fluoride (poly(CTFE-co-VDF)), dictate its microstructure and functional performance. Crystallization occurs between the glass transition (T g ≈ 31 °C) and melting point (T m ≈ 110 °C), with grain boundaries playing a key role in applications such as memristors, where they regulate filament growth. This study integrates in situ atomic force microscopy (AFM), grazing-incidence wide-angle X-ray scattering (GIWAXS), and differential scanning calorimetry (DSC) to characterize nucleation, growth, and morphology across the full crystallization window. Hot-stage AFM reveals a transition from homogeneous to heterogeneous nucleation near 45 °C and a shift from reaction-limited to diffusion-limited growth above 60 °C. Kinetics are analyzed using Lauritzen–Hoffman, Turnbull–Fisher, and Avrami models to extract surface free energies and activation barriers. A multiscale modeling framework is developed in which nucleation densities and growth rates measured by AFM are used to reconstruct Avrami kinetics, which are then validated against coverage data, and extrapolated to predict bulk crystallization behavior observed by DSC. GIWAXS confirms a primarily flat-on chain orientation at all temperatures, linking orientation to domain morphology. This integrative approach quantitatively connects nanoscale crystallization dynamics with macroscopic phase evolution, establishing a quantitative framework for modeling crystallization across time, temperature, and length scales.

Crystallization↗

DOE OSTI2026

The evolution of coal porosity during pyrolysis

Gasification of coal, municipal waste, or other organic materials is a potential hydrogen source that entails complex thermal decomposition and transport processes. This study provides a multiscale analysis of these processes for sub-bituminous (Usibelli, Healy, Alaska) and lignite (Center, North Dakota) coals and provides data useful for process design. The chemistry, mineralogy, and pore structures of pyrolyzed coal and their evolution with thermal decomposition are discussed. Samples pyrolyzed at 200–1000 °C were analyzed by small-angle neutron scattering; ultra-small, small-, and wide-angle X-ray scattering; and other complementary techniques. Scanning electron microscopy showed new pores in the high-temperature-pyrolyzed material. Upon heating, the coals became progressively denser, and the concentration of hydrogen decreased. Changes in pore volume fell into three temperature ranges: an initial, low-temperature range that, for the Usibelli coal, involved an increase in overall porosity; a mid-temperature range associated with pore volume loss; and a high-temperature range associated with significant porosity increase and char formation. This transformation was paralleled by changes in fractal dimension and correlation length. The higher the pyrolysis temperature the greater the small-pore-volume fraction and overall surface area became. Pyrolysis increased the lateral size of coal crystallites, decreased the amorphous fraction, and increased the aromatics fraction and overall coal rank. Comparisons of neutron and X-ray scattering data and subsequent water uptake studies showed that pre-dried coals can re-hydrate relatively rapidly upon exposure to air, which can significantly affect the porosity calculated from small-angle-scattering data. Fits to the cumulative porosity curves provide a method for modeling the physical and chemical transformation of hydrogen-containing feedstock during gasification.

Anovitz, Lawrence {Larry} [ORNL] (ORCID:0000000226↗

DOE OSTI2025

Enhanced Ion Transport and Molecular Packing Stability in Asymmetric 2D Nanostructured π‐Conjugated Thieno[3,2‐b]Thiophene‐Based Liquid Crystal

Organic semiconductors based on liquid crystal (LC) molecules have attracted increasing interest. Here, in this work, two linear LCs based on 2,5‐bis(thien‐2‐yl)thieno[3,2‐b]thiophene (BTTT) mesogen are designed and synthesized, including BTTT/dEO3 with two symmetrically attached tri(ethylene oxide) groups and BTTT/mEO6 with one asymmetrically attached hexa(ethylene oxide) group. These two molecules have comparable functional‐group compositions but different molecular geometries, leading to their moderately different material performances. Both LCs show smectic mesophases with relatively low transition temperatures as confirmed by differential scanning calorimetry and polarized optical microscopy. A combination of experimental grazing incidence wide‐angle X‐ray scattering and molecular dynamics (MD) simulations reveals a herringbone packing motif of BTTT segments in both LCs while a smaller molecular tilt angle in BTTT/mEO6. Ionic conductivities are measured by doping LCs with different amounts of ionic dopants, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). BTTT/mEO6 shows better smectic phase stability to higher LiTFSI doping ratios. Both LCs exhibit similar ionic conductivities in the smectic phases, but BTTT/mEO6 outperforms BTTT/dEO3 by a factor of three in the amorphous phase at higher temperatures. MD simulations, performed to examine the ion solvation environment, reveal that BTTT/mEO6 is more efficient in coordinating Li‐ions and screening their interactions with TFSI‐ions which further promote ionic transport.

grazing incidence wide-angle X-ray scattering↗

DOE OSTI2024

Characterization of sub-micrometre-sized voids in fixed human brain tissue using scanning X-ray microdiffraction

Using a 5 µm-diameter X-ray beam, we collected scanning X-ray microdiffraction in both the small-angle (SAXS) and the wide-angle (WAXS) regimes from thin sections of fixed human brain tissue from Alzheimer's subjects. The intensity of scattering in the SAXS regime of these patterns exhibits essentially no correlation with the observed intensity in the WAXS regime, indicating that the structures responsible for these two portions of the diffraction patterns, which reflect different length scales, are distinct. SAXS scattering exhibits a power-law behavior in which the log of intensity decreases linearly with the log of the scattering angle. The slope of the log–log curve is roughly proportional to the intensity in the SAXS regime and, surprisingly, inversely proportional to the intensity in the WAXS regime. We interpret these observations as being due to the presence of sub-micrometre-sized voids formed during dehydration of the fixed tissue. The SAXS intensity is due largely to scattering from these voids, while the WAXS intensity derives from the secondary structures of macromolecular material surrounding the voids. The ability to detect and map the presence of voids within thin sections of fixed tissue has the potential to provide novel information on the degradation of human brain tissue in neurodegenerative diseases.

Chemistry↗

DOE OSTI2025

Comparing the Effects of Side Chain Dipole–Dipole Interactions and Hydrogen Bonding on the Mechanical and Electrical Properties of Poly(3-hexylthiophene)

Poly(3-alkylthiophenes) are simple conjugated polymers with good electrical properties, but tend to be brittle, limiting their application. Here, we investigate how side chain modifications can improve their toughness without compromising their charge transport. Specifically, we compare a weak dipole–dipole interaction of ester groups with a stronger hydrogen-bonding interaction of the hydroxyl groups. Two copolymers with targeted 5 and 10 mol % ester-functionalized side chains were synthesized and hydrolyzed in the solid state to introduce hydroxyl groups. Both hydrolyzed polymers became insoluble in most organic solvents, providing a path to layer-by-layer solution processing. All polymers’ optical, thermal, structural, electrical, and mechanical properties were investigated. Optical spectroscopy revealed that functionalization at these low levels did not significantly affect aggregation or π–π stacking. Differential scanning calorimetry indicated reduced crystallinity in the functionalized copolymers compared to that of P3HT. Grazing-incidence wide-angle X-ray diffraction data showed that functionalization led to an increase in lamellar spacing without altering molecular orientation or π–π stacking. Mechanical testing highlighted that at the lower functionalization level, both ester and hydroxyl groups similarly enhanced toughness, suggesting that disorder, rather than the specific nature of the functional group, was responsible for these improvements. At the higher functionalization level, hydroxyl groups significantly increased the elastic modulus while also negatively impacting charge carrier mobility. This study suggests that with stronger hydrogen-bonding groups, only very small amounts can improve P3HT’s toughness. For a wider tunable range, it may be a better strategy to use weak interactions such as dipole–dipole interactions of ester groups.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Counterintuitive Compatibilization of Poly(-Valerolactone) and Poly(L-Lactic Acid) by Statistical Copolymers toward Compostable and Recyclable Packaging

Poly(δ-valerolactone) (PVL) and poly(l-lactic acid) (PLLA) are bioderivable, compostable, and chemically recyclable plastics with synergistic properties for addressing plastic waste accumulation in receiving environments. Though recyclable-by-design polymers often fall short of competing with incumbent materials, blending affords a means to leverage individual component strengths toward ideal tunable properties. Polymer blends are often immiscible, but a range of methodologies are available to promote mixing. Here, we report on the compatibilization of 9 immiscible PVL and PLLA blends with three different compatibilization agents: thermoplastic starch, synthesized PVL-co-PLLA statistical copolymers (SCPs), and synthesized PVL-b-PLLA block-type copolymers. Resulting degrees of compatibilization are observed through scanning electron microscopy, corroborated by thermal and mechanical analyses monitoring performance as a function of microdomain size. Small-angle and wide-angle X-ray scattering experiments are conducted to observe the influence of compatibilizers on individual crystalline phases to further elucidate material behavior. Molecular dynamics simulations provide key insights into the interfacial interactions between homopolymers and compatibilizers. Finally, a suite of end-of-life avenues is established by biodegradation in industrial composting conditions, chemical recycling by deconstruction to hydroxymethyl esters, and direct chemical depolymerization to lactone precursors in mixed feed. Overall, we highlight several promising blends and the counterintuitive SCP compatibilization phenomenon toward high-performance, sustainable materials.

Compatibilization, copolymer compatibilizer, bio-b↗

DOE OSTI2024

Interconnected Nanoporous Polysulfone by the Self-Assembly of Randomly Linked Copolymer Networks and Linear Multiblocks

Porous materials have attracted considerable attention due to their versatile applications, especially in water purification. Interconnected nanoporous structures are distinguished by their high degree of porosity and resistance to clogging, as well as their insensitivity to nanostructural orientation. Previous works on randomly linked copolymer systems have shown that they can effectively produce disordered cocontinuous nanostructures, which upon removal of one component yield interconnected nanoporous materials. However, the cocontinuous nanomaterials previously developed using polystyrene (PS) and poly(d,l-lactic acid) (PLA) strands, and the resulting interconnected nanoporous PS monoliths, were far too brittle to enable practical use as membranes. Here, we study the self-assembly of randomly linked copolymer networks prepared using blocks of the engineering polymer polysulfone (PSU). A wide cocontinuous regime (spanning 40 wt %) was found for randomly end-linked copolymer networks (RECNs) constructed from PSU and PLA strands, via a combination of mechanical testing, gravimetry, small-angle X-ray scattering, and scanning electron microscopy. The PSU/PLA cocontinuous nanomaterial with symmetric composition showed 2.4 times higher Young’s modulus and ~100 times greater toughness than the corresponding PS/PLA sample. The interconnected nanoporous PSU fabricated after etching of PLA even exhibited 1.6 times greater toughness than PS/PLA prior to PLA removal. To facilitate the production of thin films of cocontinuous nanomaterials, we applied solution-processable randomly linked linear PSU/PLA multiblock polymers onto ultrafiltration membranes. Here, the interconnected nanoporous PSU thin film generated by etching PLA was found to effectively reject 50 nm diameter particles without significantly compromising permeability. This discovery presents a valuable addition to the existing techniques used to fabricate PSU membranes. In contrast to traditional methods, which are sensitive to processing conditions, produce a wide range of pore sizes, and offer limited adjustability of pore size, the current technique is anticipated to enable interconnected PSU membranes with more uniform and tailorable porosity.

36 MATERIALS SCIENCE↗

DOE OSTI2025

In‐Plane Anisotropy in van der Waals NiTeSe Ternary Alloy

Abstract The anisotropic properties of materials profoundly influence their electronic, magnetic, optical, and mechanical behaviors and are critical for a wide range of applications. In this study, the anisotropic characteristics of Ni‐based van der Waals materials, specifically NiTe 2 and its alloy NiTeSe, utilizing a combination of comprehensive scanning tunneling microscopy (STM), angle‐resolved photoemission spectroscopy (ARPES), and density functional theory (DFT) calculations, are explored. Unlike 1T‐NiTe 2 , which exhibits trigonal in‐plane symmetry, the substitution of Te with Se in NiTe 2 (resulting in the NiTeSe alloy) induces a pronounced in‐plane anisotropy. This anisotropy is clear in the STM topographs, which reveal a distinct linear order of charge distribution. Corroborating these observations, ARPES measurements and DFT calculations reveal an anisotropic Fermi surface centered at the point, which is notably elongated along the k y direction, leading to directional variations in in‐plane carrier velocities. Consequently, the Fermi velocity is highest along the k x direction where the linear charge distribution aligns in real space and is lowest along the k y direction. These findings offer valuable insights into the tunability of anisotropic properties in ternary transition metal dichalcogenide systems, highlighting their potential applications in the development of anisotropic electronic and optoelectronic devices.

Chemistry↗

DOE OSTI2025

A Spatially Resolved Evaluation of Accelerated Environmental Aging on Emerging Polypropylene-Based Photovoltaic Backsheets Using Raman Spectroscopy

For this work, accelerated aging was used to assess environmental degradation in emerging co-extruded polypropylene (PP)-based backsheets under three different environmental conditions (65°C/20% relative humidity (RH), 75°C/20% RH, and 75°C/50% RH). Although differential scanning calorimetry did not measure crystallinity changes with exposure, spatially resolved Raman spectroscopy identified crystallinity increases in the core layer of aged samples, indicating a heterogeneous postcrystallization process. The Raman results were in agreement with synchrotron-based microfocused wide-angle X-ray scattering measurements. Cross-sectional nanoindentation was used to correlate localized crystallinity shifts with changes in Young's modulus. A similar trend was found where increased modulus was measured in the core layer, supporting the relationship between modulus and crystallinity. Finally, dielectric characterization was used to assess the impact of these material property changes on performance. While changes in the backsheet material properties and dielectric performance were observed with accelerated aging, these shifts generally equilibrated with time, indicating overall stability in response to environmental stressors. Additionally, the identified heterogeneous material property changes indicate that spatially resolved crystallinity measurements may be a valuable early failure indicator to be used in the assessment of PV backsheet long-term durability.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Nanoscale structural evolution and phase transformation of geopolymers: In situ SAXS/WAXS investigation under uniaxial tension at elevated temperatures

This investigation delves into the degradation mechanisms of high-density polyethylene geomembranes (PE GMXs) under a spectrum of conditions, replicating real-world scenarios within a rigorously controlled laboratory setting. The treatment protocols applied induced a notable increase in the crystallinity of the treated specimens relative to the untreated controls. Small-angle x-ray scattering (SAXS) analysis identified an initial long period (interlamellar distance) of 16.9 nm for the untreated polymer, which expanded by 19.5% at a strain of 16.7 percent. Conversely, the treated PE GMXs exhibited a more gradual elongation of the long period, with an increase of merely 10.6% at a strain of 23.3 percent. At an elevated temperature of 65°C, both samples exhibited pronounced strain hardening, with the treated PE GMXs demonstrating superior stability even at a strain of 150 percent. Wide-angle x-ray scattering (WAXS) experiments corroborated these observations, revealing that the diffraction patterns of the untreated PE remained stable up to a strain of 16.7%, whereas those of the treated PE remained distinct up to a strain of 46.1 percent. Scanning electron microscopy (SEM) images substantiated the formation of a shish–kebab structure in the treated samples. The study concludes that the geopolymer underwent oxidation and material degradation as a result of the chemical and mechanical treatments, transitioning to a more crystalline state and concomitantly losing its initial elasticity.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Formation of the {gamma}ʹʹʹ-Ni2(Cr, Mo, W) phase during a two-step aging heat treatment in HAYNES® 244® Alloy

Precipitation hardening is the dominant method of achieving high strength in most Ni-based superalloys. The formation of nanoscale precipitates during thermal exposure is often studied to determine the optimal methods of attaining high strength. The commercial Ni-based superalloy, HAYNES® 244® alloy, is strengthened through a novel -Ni2(Cr, Mo, W) intermetallic phase that forms during a two-step aging cycle. The precipitation kinetics of this intermetallic phase are sluggish for single-step aging in comparison to the γʹ phase in precipitation-strengthened Ni-based alloys, but a two-step aging treatment has shown to reliably harden the alloy and improve high-temperature properties compared to a single-step aging heat treatment. To investigate the formation and coarsening of this phase, heat-treated samples of the 244 alloy were analyzed with high-energy in situ and ex situ X-ray techniques such as small angle X-ray scattering and wide angle X-ray scattering as well as Vickers micro-hardness, electron microscopy, and atom probe tomography. The relationship between hardness, aging parameters, and microstructure evolution is discussed. The enthalpy of formation and precipitate solvus temperature were determined with high-temperature differential scanning calorimetry and dilatometry analysis.

Ni-based Superalloys↗

DOE OSTI2024

Reconstructing the reflectivity of liquid surfaces from grazing incidence X-ray off-specular scattering data

The capillary wave model of a liquid surface predicts both the X-ray specular reflection and the diffuse scattering around it. A quantitative method is presented to obtain the X-ray reflectivity (XRR) from a liquid surface through the diffuse scattering data around the specular reflection measured using a grazing incidence X-ray off-specular scattering (GIXOS) geometry at a fixed horizontal offset angle with respect to the plane of incidence. With this approach the entire Q z -dependent reflectivity profile can be obtained at a single, fixed incident angle. This permits a much faster acquisition of the profile than with conventional reflectometry, where the incident angle must be scanned point by point to obtain a Q z -dependent profile. The XRR derived from the GIXOS-measured diffuse scattering, referred to in this paper as pseudo-reflectivity, provides a larger Q z range compared with the reflectivity measured by conventional reflectometry. Transforming the GIXOS-measured diffuse scattering profile to pseudo-XRR opens up the GIXOS method to widely available specular XRR analysis software tools. Here the GIXOS-derived pseudo-XRR is compared with the XRR measured by specular reflectometry from two simple vapor–liquid interfaces at different surface tension, and from a hexadecyltrimethylammonium bromide monolayer on a water surface. For the simple liquids, excellent agreement (beyond 11 orders of magnitude in signal) is found between the two methods, supporting the approach of using GIXOS-measured diffuse scattering to derive reflectivities. Pseudo-XRR obtained at different horizontal offset angles with respect to the plane of incidence yields indistinguishable results, and this supports the robustness of the GIXOS-XRR approach. The pseudo-XRR method can be extended to soft thin films on a liquid surface, and criteria are established for the applicability of the approach.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Microphase Separation of Randomly Linked Branched Polystyrene/Polylactic Acid for Formation of Cocontinuous Nanostructures

Cocontinuous polymeric nanomaterials have gained attention for their ability to preserve distinct properties of constituent microphases within a single material. Randomly linked copolymer networks have shown very wide stability windows for disordered cocontinuous phases (extending over ≈ 30 wt % in composition), but the reliance on a network architecture prevents subsequent solution- or melt-processing. Furthermore, the key factors contributing to cocontinuity have remained unclear. We recently found that randomly linked star copolymers (RSCs) can exhibit a cocontinuous window as wide as 25 wt % in the case of 4-arm stars, suggesting that while a network architecture is not essential for the formation of disordered cocontinuous phases, the presence of random elastic forces in such architectures may indeed facilitate their formation. In addition, the behavior was found to be highly sensitive to arm number, with 6-arm RSCs exhibiting almost no cocontinuous phase. These results raised a key mechanistic question regarding the contribution of random elastic forces, originating from strands that bridge between junctions, in stabilizing disordered cocontinuous phases. In the current study, we synthesized randomly linked branched copolymers (RBCs) of polystyrene (PS) and poly(D,L-lactic acid) (PLA), which represent an intermediate architecture between networks and stars. This approach allows for the introduction of elastic contributions from strands bridging between different junctions, while still maintaining the processability advantages of a non-network architecture. The cocontinuous regions of the PS/PLA RBCs, with varying polymer and linker functionalities (f p and f l , respectively), were characterized by small-angle X-ray scattering, gravimetry, and scanning electron microscopy. We found that the cocontinuous windows of RBCs typically expanded with increasing elastic contributions and exhibited reduced sensitivity to junction-functionality compared to RSCs. Notably, RBCs with f p = 1.50 and f l = 3, which had large molecular weights due to proximity to the gel point, achieved a cocontinuous window of ≈ 34 wt %, which is almost twice as wide as analogous 3-arm RSCs and comparable to randomly linked networks. Leveraging this robust cocontinuity and solution-processability, we fabricated a film of interconnected nanoporous PS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗