Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “weld speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Unveiling mechanisms and onset threshold of humping in high-speed laser welding

The fabrication of fuel cells relies on a rapid laser welding process. However, challenges arise with the occurrence of humping when the welding speed surpasses a critical threshold, which poses difficulties in achieving a smooth surface finish and a consistent weld strength. This study aims to elucidate the humping mechanisms by analyzing the morphology of molten pool and the characteristics of melt flow at varying welding speeds via in situ synchrotron high-speed X-ray imaging and computational fluid dynamics simulations. Our findings indicate that the short keyhole rear wall, the high backward melt velocity, and the prolonged tail of molten pool are the primary factors contributing to the onset of humping. Furthermore, a dimensionless humping index (π h ) was introduced, which successfully captured the onset threshold of humping across different literatures. This index not only provides a quantitative description of the humping formation tendency but also serves as a valuable tool for optimizing the laser welding process.

42 ENGINEERING↗
DOE OSTI2025

Effects of shielding gas and spot reduction on humping suppression in high-speed laser welding

High-speed laser welding is a crucial process to enhance the production rate of fuel cell fabrication. However, exceeding a critical welding speed leads to defect formation such as humps and root concavities, which degrade weld quality and mechanical performance. This study employed shielding gas and spot reduction approaches to suppress these defects. The relationships between individual defect types and their influence on weld strength were systematically examined. Moreover, in situ high-speed synchrotron X-ray imaging was employed to comprehend the mechanisms of humping mitigation by shielding gas through analysis of instantaneous keyhole and melt pool dynamics. The observations reveal that shielding gas mitigates humping by shortening the molten pool through enhanced surface heat convection and by altering surface tension to prevent melt flow collisions. The effects of shielding gas and spot reduction were further incorporated into the dimensionless humping index (π h ) that describes the humping formation tendency. These findings provide mechanistic insights and quantitative guidance for defect control strategies in high-speed laser welding.

08 HYDROGEN↗
DOE OSTI2026

Molten pool dynamics and humping suppression in high-speed laser welding via tailored beam configurations

High-speed laser welding is essential for increasing the production rate of fuel cell fabrication. However, when the welding speed exceeds a critical limit, humping occurs and reduces the weld quality. In this study, two tailored beam configurations, including an adjustable ring mode and a dual-beam configuration, were employed to suppress humping. Computational fluid dynamics simulations were performed to elucidate the underlying suppression mechanisms. Here, the results show that, in the adjustable ring mode, humping mitigation arises from a reduced backward cross-sectional melt flow rate and a more stable molten pool. In the dual-beam configuration, humping suppression is attributed to the deceleration of melt flow, the conduction-mode behavior of the trailing beam, and the widening of the molten pool induced by the trailing laser. Furthermore, because the dual-beam configuration directly modifies the trailing molten pool dynamics, it achieves more effective humping suppression, extending the welding speed limit to 1.50 m/s, compared with 1.00 m/s for the adjustable ring mode.

08 HYDROGEN↗
DOE OSTI2023

High-speed friction stir butt welding of 25.4 mm thick 7175-T79 aluminum alloy

This presents the first experimental demonstration of friction stir butt welding of 25.4 mm thick high-strength, precipitate-strengthened 7XXX aluminum alloy at a welding speed above 500 mm/min and penetration depth greater than 10 mm. Tool pin threads that terminate away from the shoulder region, helped mitigate nearby stress concentration during tool traversing, enabling a higher welding speed while avoiding pin fracture near shoulder. Two kinds of welds—one-sided with full penetration of the plate thickness and double-sided with partial penetration of the plate thickness—were conducted. Significant grain refinement (grain size 1.3 ± 0.8 µm) was evident at the junction of double-sided friction stir welding (FSW) compared to other regions of weld-nugget or base material. Cross-weld tensile testing with digital image correlation revealed high local strains at the junction of double-sided FSW before macro-yield. This strain concentration impeded the typical early necking on advancing/retreating sides of FSW joints, improving the yield strength of as-welded double-sided FSW by 20–24% over slow- to medium-speed one-sided FSW. In conclusion, the joint efficiency of as-welded, double-sided high-speed FSW was about 76% with respect to the base material’s ultimate tensile strength.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Technique for the Quantitative Characterization of Weld Microstructure and Application to Mo Welds

The choice of weld parameters determines the size, shape, and curvature of grains in the fusion zone (FZ) and heat-affected zone (HAZ) of welds while the mechanical properties of the welds are correlated to this microstructure. Here, a new technique to quantitatively evaluate these microstructural characteristics in both zones of welds has been applied to molybdenum gas tungsten arc welds fabricated using different weld parameters. Trends in microstructural characteristics in the FZ and HAZ were evaluated and correlated with changes to heat input, weld speed, and weld technique. The use of this approach showed that a 20 pct decrease in heat input caused a 20 pct decrease in the number of FZ grains with aspect ratios ≥ 4. The orientations of the FZ grain segments as a function of distance from the FZ centerline were significantly affected by the weld speed and its effect on weld pool shape. A 50 pct increase in weld speed caused a 20 pct decrease in grain segments orientated 60 to 90 deg from the normal to the direction of welding. This technique also captured differences in grain sizes and grain size anisotropy in the FZ between welds made with a constant current, pulsed current, and use of a 4-pole-magnetic oscillator.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the quantitative characterization of weld microstructures

Here, a new technique to quantify grain shape and grain boundary curvature in the fusion zone (FZ) and the heat-effected zone (HAZ) of refractory metals and alloys has been developed. The application of this technique to quantify the effect of welding speed on these microstructural characteristics in simulated molybdenum welds is highlighted in this study. A 50% increase in weld speed more than doubles the fraction of grain segments in the fusion zone with orientations between 00 to 300 to the normal to the welding direction, with a corresponding 50% decrease in the fraction of grain segments oriented along the welding direction. This increase in weld speed also results in a reduction in grain size from approximately 120 µm to 84 µm along the WD at the FZ centerline. Grain boundary curvature is negative near the weld centerline and the edge of the fusion zone, indicating that with increasing distance from the weld centerline, the grain segments progressively rotate towards a direction normal to the welding direction at both locations. Presence of regions with relatively straight grain segments indicated by curvatures close to zero were identified in between the weld centerline and the edge of the FZ at all weld speeds.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High speed butt joining of 1” thick 2139-T8

Thick plate (=1”) butt joining of Al alloys is challenging due to high tool forces, uneven material flow, and heat distribution in the through-thickness direction. Tool design and welding parameters used for executing thick plate butt joining have remained mostly static over the past decade. Reported welding speeds that produce viable joint strength (mostly on 6xxx alloys) typically range below 100 mm/min (4inches /min). Researchers at Pacific Northwest National Laboratory (PNNL) in association with Ground Vehicle Systems Center (US Army GVSC) have been working to demonstrate greater joining efficiency at higher welding speeds in a 1” thick AA2139-T8 plate. Using innovative tool features and effective force and temperature control a joint efficiency of 80% was demonstrated at a welding speed of 7 inches /min (178mm/min).

Das, Hrishikesh↗
DOE OSTI2025

Derivation of physical equations for high-speed laser welding using large language models

It is challenging to formulate complex physical phenomena that occur in a manufacturing process, particularly when the available data are limited, rendering conventional data-driven approaches ineffective. This study aims to predict humping onset in high-speed laser welding by introducing a novel framework, namely text-to-equations generative pre-trained transformer (T2EGPT). This method leverages the capabilities of large language models (LLMs), in combination with sparse experimental data and enriched literature data, to derive an interpretable and generalizable equation for predicting humping initiation. By capturing key correlations among physical parameters, T2EGPT generates a compact and dimensionless expression that accurately predicts hump formation. The equation reveals that humping arises from the interplay between inertia-driven backward melt flow and capillary-driven surface stabilization, where inertial forces drive molten metal backward and capillary forces resist surface deformation. Furthermore, compared to traditional data-driven models, T2EGPT demonstrates enhanced predictive accuracy and cross-material transferability. More broadly, this study highlights the potential of LLMs to integrate textual information with data-driven discovery, enabling the extraction of physical laws in data-scarce scientific domains.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Towards High-Speed friction stir welding of 25 mm Thick AA2139-T8: tool innovation and process development

Joining thick plates (≥ 12 mm) of aluminum (Al) alloys is challenging due to high tool forces, uneven material flow, and non-uniform heat distribution through the material’s thickness. Recent advancements in tool design and welding parameters for friction stir welding (FSW) in thick plates butt joining have encountered a developmental plateau, highlighting the need for innovative approaches to overcome existing limitations. Here, this study focuses on the systematic development of single-pass and double-pass FSW processes for high-strength aluminum alloy AA2139-T8, to improve joint efficiency and enable high-speed welding capabilities. Experimental evidence is presented for a novel tool design with opposing pin threads, enabling high-speed (178 mm/min) single-pass friction stir butt welding of 25 mm thick AA2139-T8. A series of FSW trials was conducted both in air and with a trailing water spray, using steel backing plates (BPs) to investigate the impact of quenching and cooling rates on process response and joint performance. A joint efficiency of 83% was attained using the novel tool features and effectively controlling process forces and thermal boundary conditions.

AA2139-T8↗
DOE OSTI2021

Three Sheet Al alloy assembly for automotive application

An update on joint characterization of three sheet friction stir lap welds (FSLW) in three aluminum alloys (7xxx, 5xxx, and 6xxx) for automotive assembly application is presented. Welding speed of 0.3-2.9m/min was used with pin length >5mm with the aim to reduce upturn hooking on the retreating side and avoid wormhole defect on the advancing side. Joints were also made in to enable T peel and U peel testing. Stitch welds were used to understand effects of weld length and ramp length on T peel performance. Hat sections were joined for 3-point bending and axial crush testing and tested with promising results. Several key issues that require further investigations are identified including flash management near the trim edge, weld quality with limited clamping, tool failures at speeds greater than 0.5m/min, and propensity of incipient melting for 7xxx stack-up.

Upadhyay, Piyush↗
DOE OSTI2023

Friction stir welding of thick 7175 aluminium alloy plates for deepwater riser applications

To substantially reduce the cost of extracting petroleum from ultra-deepwater sources, manufacturing risers from 7175 aluminium (Al) alloys rather than steels is being considered. Friction stir welding (FSW), a solid-phase joining technique, is widely applied to 7XXX Al alloys because its mechanical properties are retained within the nugget zone. And, the primary technical objective of the current study is the development of high-strength, corrosion-resistant weldments that connect 7175 Al riser flanges and pipes. However, as the welding thickness increases, the welding speed can be greatly impeded, which lowers the manufacturing efficiency and weakens the mechanical properties in the heat affected zone (next to the nugget). Therefore, obtaining high-performance thick plate 7175 Al alloy joints via FSW is challenging. To overcome this dilemma, the current work optimises the tool design and welding parameters for achieving high-performance joints between 25.4 mm thick 7175 Al alloy plates in butt joint configuration.

Wang, Tianhao↗
DOE OSTI2021

Characterization of fusion welded ceramics in the SiC-ZrB 2 -ZrC system

Various SiC-ZrB 2 -ZrC ceramics were joined by fusion welding to determine the maximum silicon carbide content that could be joined. Commercial powders were hot pressed, machined, and preheated to 1450 °C before joining with a tungsten inert gas welding torch at 160–200 A. Resulting welds were cross-sectioned and analyzed to determine which compositions were weldable and to characterize microstructural evolution in welded samples. As compositions approached the ternary eutectic, the welds had smaller SiC grains and exhibited better weldability. Penetration depth of welds was controlled by a combination of current input and welding speed. Here, the ternary eutectic in the system was found at 36.9 ± 1.3 vol% SiC, 42.7 ± 1.5 vol% ZrB 2 , and 20.4 ± 1.9 vol% ZrC and its melting temperature was 2330 ± 23 °C. A ternary phase diagram for the SiC-ZrB 2 -ZrC was constructed and proposed via microstructural analysis of arc melted pellets on binary joins between each binary eutectic and the ternary eutectic in the system.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of Backing Plate and Thermal Boundary Conditions for High-Speed Friction Stir Welding of 25-mm Thick Aluminum Alloy 7175-T79

Here this study demonstrates high-speed (150 mm/min) single pass friction stir butt joining of 25 mm thick aluminum alloy 7175-T79. To understand the impact of quenching and cooling rate on process responses, joint strength, and grain size distributions across the weld thickness, we performed a series of friction stir welding (FSW) trials in air and with a trailing water spray using steel and composite backing plates (BP). Welds made in air and trailing water spray exhibit significantly different hardness distributions across the nugget, heat affected zone (HAZ), and HAZ minimum hardness as evidenced by detailed microhardness mapping. The effect of trailing water spray (TWS) on joint efficiency overshadows the influence of BP composition due to the vastly different contribution to quenching. TWS also resulted in a multifaceted effect on FSW such as lowering processing temperature, increasing X and Z forces while lowering Y force, and narrow heat affecting zone. Finally, digital image correlation (DIC)-based fracture mode analysis and grain size measurements correlate with the hardness distribution.

42 ENGINEERING↗
DOE OSTI2023

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Weldability of irradiated Stainless Steel 304 materials harvested from the National Research Universal (NRU) reactor

In this work, the weldability of the neutron-irradiated Stainless Steel 304 (SS 304) materials containing estimated helium levels of 12 to 44 appm has been studied through a Collaborative Research and Development Agreement between the Canadian Nuclear Laboratories and Oak Ridge National Laboratory. The work utilizes a SS 304 component harvested from the National Research Universal reactor. Laser beam welding was used to explore suitable welding conditions and associated parameters, to determine helium concentration limits for successful welding of irradiated stainless-steels. The experimental results show that maximum fusion zone void sizes, fusion zone void quantity and total heat affected zone helium-induced crack length generally increased with increasing He levels and effective weld heat input. A proper combination of welding parameters with low effective heat input, such as, laser power, weld travel speed and wire feed speed, were shown to improve the welding quality, and potentially reduce the length and probability of the formation of grain boundary helium-induced cracking and voids of irradiated SS 304 even with He concentrations as high as about 44 appm.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-Speed and High-Quality Field Welding Repair Based on Advanced Non-Destructive Evaluation and Numerical Modeling

Creep strength-enhanced ferritic (CSEF) steels such as Grade 91 (9Cr-1Mo-V) and Grade 92 (Fe-9Cr-2W-0.5Mo) steels are widely used in the fossil-fuel-fired and nuclear power plants. The weld integrity of these steels is crucial for power plants' safe and reliable operations. Due to harsh service conditions, the steel weld can become susceptible to environmental degradation. Field welding repair is used to restore the degraded weld’s performance where a controlled temper-bead welding technique is commonly used to temper the freshly formed martensite during welding. However, knowledge of weld repairability is limited and experimental trial and error optimization to achieve desired microstructure and joint properties is expensive and time-consuming. Many existing computational models, e.g., finite element models, are limited to solving heat conduction equation and ignoring convective heat transfer due to molten metal flow. These models can result in over-prediction of peak temperatures of weld pool and heat-affected zone (HAZ), which in turn can affect the accuracy of tempering prediction. Moreover, these finite element models require an input of the deposit profiles in advance and thus limits the usability of these models. Here, a molten pool-based, multi-pass multi-layer model has been developed based on computational fluid dynamics (CFD) approach with the Volume of Fluid (VOF) method. The model calculates the bead formation, thereby eliminating the need for pre-determined bead profiles required by finite element models. For computational efficiency, a coordinate system attached to the moving heat source is utilized. A subroutine is developed to convert the temperature profiles in the reference frame stationary to the heat source to that stationary to the workpiece. The converted thermal cycles are then imported into a microstructure model to compute the tempering kinetics and resultant hardness using a Johnson-Mehl-Avrami-Kolmogorov (JMAK), and modified Grange-Baughman parameter. The modeling approach is first developed and validated on single- and multi-pass deposition of stainless steel filler metal onto a SA-533 high strength steel substrate. The models are then applied to a multi-pass V-groove repair weld of Grade 91 steel plate as well as directed energy deposition of Grade 92 steel. Non-destructive characterization of microstructures was performed on Grade 91 and 92 steel welds. Two welding processes, cold metal transfer (CMT) and flux-cored arc welding (FCAW), were investigated for the Grade 91 steel weld samples. For the Grade 92 weld samples, three different heat inputs (low, medium, and high) of gas tungsten arc welding (GTAW) were utilized to replicate traditional field welding processes. The non-destructive evaluation (NDE) method used for this research was immersion ultrasonic testing (UT) using a micro-resolution ultrasonic imaging methodology specifically designed to operate in the through-transmission configuration operating at 20 MHz of frequency. The system used a focused ultrasonic beam spot size diameter between 250-300 μm, and a 6 μm laser vibrometer spot size for detection, to produce highly defined images with longitudinal and mode-converted shear waves. From the micro-resolution ultrasonic C-scan images, three microstructural regions, i.e., weld metal (WM), HAZ, and base metal (BM), were clearly identifiable. Various levels of ultrasonic amplitudes distributed over the three regions were correlated with electron beam backscattered diffraction (EBSD) images using grain size, grain boundaries, and dislocation densities. The results showed that areas with relatively higher ultrasonic amplitude levels were associated with smaller grains and higher dislocation densities, while areas with lower amplitude levels were associated with larger grains and lower dislocation densities. In addition, ultrasonic velocity data obtained across the three different weld microstructural regions of Grade 91 test samples were correlated with optical metallographic images and hardness measurements. The results showed distinctive decreases in ultrasonic velocity and hardness over the HAZ region, where weld failures often occur during service.

36 MATERIALS SCIENCE↗