SEARCH · Engineering Papers
Results for “water resources engineering”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Field-scale estimation of soil properties from spectral induced polarization tomography
Estimates of soil properties such as Cation Exchange Capacity (CEC), water content, grain size characteristics, and permeability are important in geotechnical engineering, water resources, and agriculture. We develop a non-intrusive approach to estimate these properties in the field using spectral induced polarization (SIP) tomography. This geophysical method provides information about the frequency dependence of the complex electrical conductivity of porous media. Using 18 soil samples collected from a Bordeaux vineyard, we first conducted a laboratory study using SIP over the frequency range 10 mHz-45 kHz. The laboratory data were used to confirm the accuracy of a recently developed dynamic Stern layer petrophysical model. The results are consistent with published values from previous works using soils. A comparison was made by comparing the field complex conductivity spectra and the experimental data at two locations where core samples were obtained. The model was then used in concert with field data to image the spatial distribution of CEC, water content, permeability, and mean grain size along a vineyard transect. For clay and sandy textures found in the field, measured and estimated CEC agree rather well (from 6 to 40% discrepancy). Furthermore, our approach provides an efficient way to estimate important soil properties in a non-invasive manner, in high resolution, and over field-relevant scales of the critical zone of the Earth.
Identifying optimal photovoltaic technologies for underwater applications
Not Available
Mineral Recovery Enhanced Desalination (MRED) process: An innovative technology for desalinating hard brackish water
Desalination of water containing high concentrations of calcium, dissolved carbon dioxide, sulfate, silica and other sparingly soluble salts is difficult because of the scaling potential. An innovative pre-treatment scheme was investigated at bench scale that selectively removes these constituents and produces a soft water to enable desalination with high feed water recovery. The process first removes dissolved carbon dioxide by air stripping at low pH. Magnesium is removed by precipitation at high pH. Calcium is removed by ion exchange (IX), and sulfate is removed by nanofiltration (NF). Cation regenerant from IX, containing calcium, and concentrate from NF, containing sulfate, is combined to precipitate gypsum. Concentrate from the desalination process consisting of a concentrated NaCl solution is used to regenerate the IX resins. The selective precipitation, IX, and NF processes were tested in laboratory experiments and produced magnesium hydroxide and gypsum at greater than 90% and 95% purity respectively. A process model was developed to calculate process performance, mass and liquid flow rates. Finally, the MRED process offers the following benefits: 1) greater recovery of brackish feedwater by a desalination process, 2) recovery of marketable commodities and 3) reduction in the volume and mass of waste products from the treatment process.
Effect of different manufacturing methods on polyamide reverse-osmosis membranes for desalination: Insights from molecular dynamics simulations
Membranes are a key technology platform for a broad application of energy-efficient separations. To best serve the separation demands of industry, the manufacturing processes for these membranes are garnering increasing attention. In particular, for water desalination, the industry leading polyamide (PA) reverse osmosis (RO) membranes can be manufactured via molecular layer-by-layer (mLBL) deposition, interfacial polymerization (IP), and 3D-printing technique. However, the influence of different manufacturing methods on PA membrane’s properties is far from understood. Here, in this study, we present the high-pressure transport behavior of water and salt ions for PA membranes formed with IP, mLBL, and 3D-printing through non-equilibrium molecular dynamics simulations. Studies show that membranes fabricated with 3D-printing have similar performances to those manufactured using mLBL, quantified by water permeability, rejection of salt ions, structural integrity, and porosity features. However, the membranes formed with IP exhibit faster water transport, lower rejection, worse structural integrity, and more inhomogeneous network pores than those constructed using mLBL and 3D-printing. The unconnected water-accessible space governs water transport for PA membranes formed with mLBL and 3D-printing, which offers the impermanent open-closed pores that enable water to jump through PA membranes. In contrast, the permeated water-enterable space plays a prominent role in water movement across the PA membrane formed with IP, providing a continuous transport channel at high pressure. Importantly, we observe the more significant compaction features at high pressure for PA membranes formed with IP than mLBL and 3D printing. In short, these findings provide a comprehensive understanding of existing membrane preparation technologies. It also provides a guide for developing the new membrane preparation process at the molecular level.
Performance characteristics on up-scaling vacuum membrane distillation modules
Not provided.
In-situ imaging to elucidate on scaling and wetting in membrane distillation
Not provided.
The solution-diffusion model for water transport in reverse osmosis: What went wrong?
Not provided.