SEARCH · Engineering Papers

Results for “uranium electropolish”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

3 records

All sources NASA NTRS DOE OSTI

DOE OSTI2020

A short tutorial on uranium electropolishing

Electropolishing of uranium metal is best performed in a simple aqueous solution of phosphoric acid. With +3 to +10 volts of bias potential applied to the uranium (anode) relative to a Pt counter electrode (cathode). As summarized in a Pourbaix stability diagram, these conditions yield dissolution of the U surface as UOX containing solution species without the possibility of injecting hydrogen into the metal surface. However, if the uranium is biased to negative potentials relative to the counter electrode then water may be reduced at the U surface and hydrogen gas becomes available for reaction with the U metal. The stability diagram may be modified if there are other complexing species present in solution and the potential scale shifted if a different metal is use for the counter electrode. These effects can be understood in a known way as long as solution and electrochemical cell conditions are recognized.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2022

Electropolishing of a Full-Sized U-10Mo Plate

Electropolishing is used to remove material from the surface of a metal using electric potential and current. U-10Mo fuel is produced from a low enriched uranium plate alloyed with 10% molybdenum (U-10Mo). Electropolishing is being considered in two steps of the process of fabricating this U-10Mo fuel. First, it could be used as a means initially improving the surface finish of the cast plate while removing smut from the casting process from the surface prior to homogenization. Second, it could be used again after homogenization to remove oxidation and continue to improve the surface finish prior to hot rolling. The purpose of this work is to demonstrate the process on full-size ingots and optimize the process. A depleted uranium U-10Mo plate was electropolished three times: the first two times were prior to homogenization and the third after a homogenization step. The first two polishes decreased the overall roughness, as measured by laser confocal microscopy. After each polish, a smoother and shinier blue-gold surface was left on the plate. Upon homogenization, the surface had a more matte appearance and the surface roughness increased back to the pre-homogenization values obtained prior to the initial polish. After electropolishing the homogenized pieces, the changes in surface roughness increased, as measured by laser confocal microscopy. The final polishing step was not long enough to return the surface roughness to pre-homogenization conditions, implying less polishing is needed before the homogenization versus afterwards. Heat generation during the polish was addressed by circulating the electrolyte solution through an external heat exchanger; however, solubility and anodization challenges require further study.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Developments Towards FRIB Upgrade to 400 MeV/u for Heaviest Uranium Ions

High-Q₀ medium-velocity (beta opt = 0.6) 5-cell elliptical cavities for superconducting linacs are critical technology for advancing current and future projects such as the Proton Improvement Plan II linac and the proposed energy upgrade of Michigan State University’s Facility For Rare Isotope Beams linac, FRIB400. Previous work established the validity of the novel geometry of the FRIB400 prototype 644 MHz 5-cell elliptical β = 0.65 cavities for future high Q₀ development. In collaboration with FNAL, two leading-edge high-Q₀ recipes, N-doping and Mid-T baking, were tested in the 5-cell format. 2/0 N-doping + cold electropolishing was successful at achieving FRIB400 and PIP-II Q₀ requirements, achieving an unprecedented 3.8 x 10¹⁰ at 17.5 MV/m, satisfying the FRIB400 Q₀ requirements by 1.75 times in a low-gauss environment. Mid-T baking exceeded FRIB400 Q₀ requirements by 1.4 times, and benefitted from decreased residual resistance compared to the N-doped cavity test. Systematic ultrasonic thickness measurements in single-cell revealed bulk (150 microns) EP with the modified EP tool is consistent across the inner surfaces of the cavity walls.

43 PARTICLE ACCELERATORS↗