Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “unconventional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Study of unconventional aircraft engines designed for low energy consumption

A study of unconventional engine cycle concepts, which may offer significantly lower energy consumption than conventional subsonic transport turbofans, is described herein. A number of unconventional engine concepts were identified and parametrically studied to determine their relative fuel-saving potential. Based on results from these studies, regenerative, geared, and variable-boost turbofans, and combinations thereof, were selected along with advanced turboprop cycles for further evaluation and refinement. Preliminary aerodynamic and mechanical designs of these unconventional engine configurations were conducted and mission performance was compared to a conventional, direct-drive turofan reference engine. Consideration is given to the unconventional concepts, and their state of readiness for application. Areas of needed technology advancement are identified.

Neitzel, R. E.↗
NASA NTRSDate not supplied

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis. This analysis is in support of the NASA ROAMX project. The outer mold was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here, along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high-Mach number flow. Six different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. All six blade designs are first studied under rotation in pure vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aerodynamic analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. However, the effect of aerodynamic loads on 3D stresses and the blade control load is found to be minimum. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗
NASA NTRS2023

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis in support of the NASA ROAMX project. The outer mold line was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high subsonic Mach number. Four different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. First, torsional stability is calculated for each of the designs – especially important due to the low Lock number on Mars. All four blade designs are studied under rotation in vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aeromechanical analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗
NASA NTRS1976

Study of unconventional aircraft engines designed for low energy consumption

Declining U.S. oil reserves and escalating energy costs underline the need for reducing fuel consumption in aircraft engines. The most promising unconventional aircraft engines based on their potential for fuel savings and improved economics are identified. The engines installed in both a long-range and medium-range aircraft were evaluated. Projected technology advances are identified and evaluated for their state-of-readiness for application to a commercial transport. Programs are recommended for developing the necessary technology.

Gray, D. E.↗
NASA NTRS1978

An unconventional approach to imaging radar calibration

An unconventional approach to imaging radar calibration was considered for the entire system, including the imaging processing as a measurement instrument. The technique made use of a calibrated aircraft scatterometer as a secondary standard to measure the backscatter (sigma zero) of large units of constant roughness. These measured roughness units when viewed by an imaging radar system can be used to provide gray scale level, corresponding to known degrees of roughness. To obtain a calibrated aircraft scatterometer, a homogeneous smooth surface was measured by both the aircraft scatterometer and a sphere calibrated ground system. This provided a measure of the precision and accuracy of the aircraft system. The aircraft system was then used to measure large roughness units in the Death Valley, California area. Transfer of the measured roughness units to radar imagery was demonstrated.

Fenner, R. G.↗
NASA NTRS1978

Flight experience with manually controlled unconventional aircraft motions

A modified YF-16 aircraft was used to flight demonstrate decoupled modes under the USAF Fighter Control Configured Vehicle (CCV) Program. The direct force capabilities were used to implement seven manually controlled unconventional modes on the aircraft, allowing flat turns, decoupled normal acceleration control, independent longitudinal and lateral translations, uncoupled elevation and azimuth aiming, and blended direct lift. This paper describes the design, development, and flight testing of these control modes. The need for task-tailored mode authorities, gain-scheduling and selected closed-loop design is discussed.

Barfield, A. F.↗
NASA NTRS1981

Studies of some unconventional systems for solving various landing problems

Solutions to various landing problems were obtained through unconventional systems. The first, of these is the air cushion landing system, where efforts were concentrated on development of adequate braking and steering systems and an improved understanding of scaling laws and behavior. The second was concentrated on use of a wire brush skid as a drag producing device, which was shown to have good friction coefficients and reasonable wear rates at ground bearing pressures up to 689 kPa and forward speeds up to 80 km/hr. The third showed great promise in an active control landing gear where significant load reductions were possible during landing impact and subsequent rollout.

Leland, T. J.↗
NASA NTRS1983

Design and fabrication of conventional and unconventional superconductors

The design and fabrication of conventional and unconventionally processed Ti-Nb base and Al5-compound-base, respectively, composite superconductors is discussed in a nine section review. The first two sections introduce the general properties of alloy and compound superconductors, and the design and processing requirements for the production of long lengths of stable low loss conductor. All aspects of flux jump stability, and the general requirements of cryogenic stabilization are addressed. Conductor design from an a.c.-loss standpoint; some basic formulae describing hysteretic and eddy current losses and the influences on a.c. loss of filament diameter, strand (conductor) diameter, twist pitch, and matrix resistivity are discussed. The basic techniques used in the fabrication of conventional multifilamentary conductors are described.

Collings, E. W.↗
NASA NTRS1984

Unconventional missile concepts from consideration of varied mission requirements

The characteristics of a series of unconventional missile configurations are reviewed in the light of specific mission requirements, taking volumetric efficiency and aerodynamic performance into account. Cones with and without delta wings, thick delta wings, a semiconical body with delta wings, a ring wing, a flat body with half-ring or swept-parasol wings, a parasol-wing/body with a high/low wing, and monoplanar missiles with circular or elliptical bodies are described and illustrated. Mission requirements discussed include tactical and strategic penetration, maneuverability, load-carrying capability, low detectability, low cost, and ease of carriage and storage. In general, delta configurations offer high speed and good load-carrying ability at low altitudes; parasol configurations give high lift and low drag at high altitude and speed; and monoplanar-elliptical configurations have high lift and low drag with good maneuvering and stability.

Spearman, M. L.↗
NASA NTRS1986

The development of an unconventional food regeneration process: Quantifying the nutritional components of a model methylotrophic yeast

A hybrid chemical/biological approach to unconventional food regeneration is discussed. Carbon dioxide and water, the major wastes of human metabolism would be converted to methanol by one of several physiochemical processes available (thermal, photocatalytic, etc.). Methanol is then used to supply carbon and energy for the culture of microorganisms which in turn produce biological useful basic food stuffs for human nutrition. Our work has focused on increasing the carbohydrate levels of a candidate methylotrophic yeast to more nearly coincide with human nutritional requirements. Yeasts were chosen due to their high carbohydrate levels compared to bacteria and their present familiarity in the human diet. The initial candidate yeast studied was a thermotolerant strain of Hansenula polymor pha, DL-1. The quantitative results that permit an evaluation of the overall efficiency in hybrid chemical/biological food production schemes are discussed. A preliminary evaluation of the overall efficiency of such schemes is also discussed.

Petersen, G. R.↗
NASA NTRS1990

Theoretical performance of unconventional propellants and fuel/oxidizer combinations

A comparative study is made to identify the most advantageous fuel/oxidizer combinations which could be supplied to spacecraft from in situ resources or from the most economical earth-transported storable fuels. The performance of the unconventional fuel/oxidizer combinations in question are computed for a wide range of pressures, expansion ratios and initial temperatures. The propellants discussed are, (1) for LEO: H2 + O2, NH3 + N2O4; (2) for the moon: CH4 + O2, SiH4 + O2, H2 + Al + O2, butyl rubber + O2, silicone + O2, and polystyrene + O2; and (3) for Mars: CO + O2, CO + H2O2, CO + N2O4, C2H5OH + O2, and CH3OH + O2.

Rascon, Mario↗
NASA NTRS1990

Numerical computation of viscous flow about unconventional airfoil shapes

A new two-dimensional computer code was developed to analyze the viscous flow around unconventional airfoils at various Mach numbers and angles of attack. The Navier-Stokes equations are solved using an implicit, upwind, finite-volume scheme. Both laminar and turbulent flows can be computed. A new nonequilibrium turbulence closure model was developed for computing turbulent flows. This two-layer eddy viscosity model was motivated by the success of the Johnson-King model in separated flow regions. The influence of history effects are described by an ordinary differential equation developed from the turbulent kinetic energy equation. The performance of the present code was evaluated by solving the flow around three airfoils using the Reynolds time-averaged Navier-Stokes equations. Excellent results were obtained for both attached and separated flows about the NACA 0012 airfoil, the RAE 2822 airfoil, and the Integrated Technology A 153W airfoil. Based on the comparison of the numerical solutions with the available experimental data, it is concluded that the present code in conjunction with the new nonequilibrium turbulence model gives excellent results.

Ahmed, S.↗
NASA NTRS1996

Optimization Methodology for Unconventional Rocket Nozzle Design

Several current rocket engine concepts such as the bell-annular tripropellant engine, and the linear aerospike being proposed for the X-33, require unconventional three-dimensional rocket nozzles which must conform to rectangular or sector-shaped envelopes to meet integration constraints. These types of nozzles exist outside the current experience database, therefore, development of efficient design methods for these propulsion concepts is critical to the success of launch vehicle programs. Several approaches for optimizing rocket nozzles, including streamline tracing techniques, and the coupling of CFD analysis to optimization algorithms are described. The relative strengths and weaknesses of four classes of optimization algorithms are discussed: Gradient based methods, genetic algorithms, simplex methods, and surface response methods. Additionally, a streamline tracing technique, which provides a very computationally efficient means of defining a three-dimensional contour, is discussed. The performance of the various optimization methods on thrust optimization problems for tripropellant and aerospike concepts is assessed and recommendations are made for future development efforts.

Follett, W.↗