Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “two-stage optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A nonlinear programming approach for optimizing two-stage lifting vehicle ascent to orbit

An optimal atmospheric flight branched trajectory-shaping capability is presented based on the Davidon-Fletcher-Powell variable metric parameter optimization technique. Gradient information is generated using finite difference methods. A typical atmospheric flight branched optimization problem is analyzed which requires the determination of 31 parameters. This parameter set includes the three-dimensional description of vehicle attitude control angles for three branches of flight: first-stage ascent, second-stage ascent, and first-stage flyback. The important inflight inequality contraints required to maintain the integrity of the vehicles are considered. Some of the numerical methods employed are discussed, along with several new auxiliary techniques developed to improve the compatibility of the numerical gradient and iterator.

Kamm, J. L.↗
NASA NTRS1975

Two-stage fan. 4: Performance data for stator setting angle optimization

Stator setting angle optimization tests were conducted on a two-stage fan to improve efficiency at overspeed, stall margin at design speed, and both efficiency and stall margin at partspeed. The fan has a design pressure ratio of 2.8, a flow rate of 184.2 lb/sec (83.55 kg/sec) and a 1st-stage rotor tip speed of 1450 ft/sec (441.96 in/sec). Performance was obtained at 70,100, and 105 percent of design speed with different combinations of 1st-stage and 2nd-stage stator settings. One combination of settings, other than design, was common to all three speeds. At design speed, a 2.0 percentage point increase in stall margin was obtained at the expense of a 1.3 percentage point efficiency decrease. At 105 percent speed, efficiency was improved by 1.8 percentage points but stall margin decreased 4.7 percentage points. At 70 percent speed, no change in stall margin or operating line efficiency was obtained with stator resets although considerable speed-flow requlation occurred.

Burger, G. D.↗
NASA NTRS2026

Experimental Demonstration of a Supersonic Spike Ejector

Spike diffusers are presented as a means to improve supersonic ejector efficiency via reduction in shock losses. Design, fabrication, and testing of an articulated prototype is described. Experimental results are compared to empirical performance curves representing the loci of optimal one- and two-stage conventional ejectors driven by dry air and discharging to atmosphere. Operated at a compression ratio of ~10 with all inputs equal, the spike ejector is shown to have achieved up to 2.19X and 1.83X the secondary mass throughput of the one- and two-stage references, respectively. This suggests the potential of spike diffusers to reduce ejector operating costs by ~50%.

wind tunnel↗
NASA NTRS1982

Development and operating characteristics of an advanced two-stage combustor

Results are presented from an experimental program aimed at optimizing the features of an advanced two-stage combustor that currently is being developed as part of the National Aeronautics and Space Administration/Pratt & Whitney Aircraft Energy Efficient Engine program. The combustor is designed to meet stringent goals for performance, emissions, durability and operational characteristics. An overview of the design selection process in light of these goals is discussed. Combustor rig test results, which highlight the techniques used to reduce emissions, development of the pilot and main power zone fuel injection systems, and methods of achieving efficient fuel staging, are presented.

Greene, W.↗
NASA NTRS1971

Study of Alternate Space Shuttle Concepts. Volume 2. Part 1: Concept Analysis and Definition

Three different space shuttle systems have been defined and analyzed. The first is a stage-and-one-half system optimized to meet program requirements. The second is a two-stage, fully reusable system also designed to meet program requirements. The third is a convertible system which operates initially as a stage-and-one-half system and is subsequently converted to a two-stage, fully reusable system by reconfiguration of the orbiter vehicle and development of a booster vehicle. The design and performance of this third system must necessarily be compromised somewhat to facilitate the conversion. For each system, the applicable requirements, ground rules, and assumptions are defined. The characteristics of each system are listed and a detailed description and analysis of the system are presented. Finally, a cost analysis for the system is given.

Source record↗
NASA NTRS1981

Optimal air-breathing launch vehicle design

A generalized two-point boundary problem methodology, similar to techniques used in deterministic optimal control studies, is applied to the design and flight analysis of a two-stage air-breathing launch vehicle. Simultaneous consideration is given to configuration and trajectory by treating geometry, dynamic discontinuities, and time-dependent flight variables all as controls to be optimized with respect to a single mathematical performance measure. While minimizing fuel consumption, inequality constraints are applied to dynamic pressure and specific force. The optimal system fuel consumption and staging Mach number are found to vary little with changes in the inequality constraints due to substantial geometry and trajectory adjustments. Staging, from an air-breathing first stage to a rocket-powered second stage, consistently occurs near Mach 3.5. The dynamic pressure bound has its most pronounced effects on vehicle geometry, particularly the air-breathing propulsion inlet area, and on the first-stage altitude profile. The specific force has its greatest influence on the second-stage thrust history.

Hattis, P. D.↗
NASA NTRS1973

Optimization studies in the support design for the Large Space Telescope.

A two-stage computer-oriented process is described to design the optimum mirror supports for the NASA Large Space Telescope. Using an element model for the mirror, a set of support displacements is determined so as to minimize the rms optical surface disturbances with respect to a best-fit surface. The second stage uses the STRUDL II-STOP finite element optimization system (a branch and bound approach) to obtain a minimum weight design for the support structure subject to the displacement constraints.

Cella, A.↗
NASA NTRS1983

Critical research and advanced technology (CRT) support project

A critical technology base for utility and industrial gas turbines by planning the use of coal-derived fuels was studied. Development tasks were included in the following areas: (1) Combustion - investigate the combustion of coal-derived fuels and methods to minimize the conversion of fuel-bound nitrogen to NOx; (2) materials - understand and minimize hot corrosion; (3) system studies - integrate and focus the technological efforts. A literature survey of coal-derived fuels was completed and a NOx emissions model was developed. Flametube tests of a two-stage (rich-lean) combustor defined optimum equivalence ratios for minimizing NOx emissions. Sector combustor tests demonstrated variable air control to optimize equivalence ratios over a wide load range and steam cooling of the primary zone liner. The catalytic combustion of coal-derived fuels was demonstrated. The combustion of coal-derived gases is very promising. A hot-corrosion life prediction model was formulated and verified with laboratory testing of doped fuels. Fuel additives to control sulfur corrosion were studied. The intermittent application of barium proved effective. Advanced thermal barrier coatings were developed and tested. Coating failure modes were identified and new material formulations and fabrication parameters were specified. System studies in support of the thermal barrier coating development were accomplished.

Furman, E. R.↗
NASA NTRS1972

Application of polyimide actuator rod seals

Development of polyimide two-stage hydraulic actuator rod seals for application in high-performance aircraft was accomplished. The significant portion of the effort was concentrated on optimization of the chevron and K-section second-stage seal geometries to satisfy the requirements for operation at 450 K (350 F) with dynamic pressure loads varying between 200 psig steady-state and 1500 psig impulse cycling. Particular significance was placed on reducing seal gland dimension by efficiently utilizing the fatigue allowables of polyimide materials. Other objectives included investigation of pressure balancing techniques for first-stage polyimide rod seals for 4000 psig 450 K(350 F) environment and fabrication of a modular retainer for the two-stage combination. Seals were fabricated in 0.0254 m (1.0in.) and 0.0635 m (2.5in.) sizes and tested for structural integrity, frictional resistance, and endurance life. Test results showed that carefully designed second stages using polyimides could be made to satisfy the dynamic return pressure requirements of applications in high-performance aircraft. High wear under full system pressure indicated that further research is necessary to obtain an acceptable first-stage design. The modular retainer was successfully tested and showed potential for new actuator applications.

Watermann, A. W.↗
NASA NTRS1989

Dual-fuel versus single-fuel propulsion systems for AMLS applications

The results of using a computerized preliminary design system to integrate propulsion systems examined as a part of the Space Transportation Main Engine (STME) and Space Transportation Booster Engine (STBE) studies with reference vehicle concepts from the Advanced Manned Launch System (AMLS) study are presented. The major trade study presented is an analysis of the effect of using a single fuel for both stages of two-stage AMLS reference vehicles as opposed to using a separate fuel for the boosters. Other trade studies presented examine the effect of varying relevant engine parameters in an attempt to optimize the reference engines for use with the AMLS launch vehicles. In each propulsion trade discussed, special attention is given to the major vehicle performance and operational issues involved.

Stanley, Douglas O.↗
NASA NTRS1975

Efficient optimal design of suspension systems for rotating shafts

A new technique is proposed for the optimum design of suspension systems for rotating shafts. In this approach the conventional method of trial and error search for optimum parameter values for a prescribed design configuration has been replaced by an efficient two-stage procedure. In the first stage a generic force is substituted for the suspension system to be designed and the absolute optimum (or limiting) performance characteristics of the shaft are computed. In the second stage, using a chosen suspension system configuration, parameter identification techniques are are applied to find the design parameters so that the suspension system will respond as close as possible to the absolute optimal performance. In this approach the repetitive shaft analyses required in the conventional search techniques are avoided. Hence, the new technique is relatively efficient computationally and is suitable for large systems. Both linear and nonlinear suspension systems can be designed. A simple Jeffcott rotor is used to demonstrate the new technique.

Pilkey, W. D.↗
NASA NTRS1974

Mars surface-to-orbit vehicles for sample return missions

Review of the results of a Mars surface-to-orbit launch vehicle study using an upgraded atmospheric density profile and an ascent trajectory optimization program. Orbit insertion was achieved with velocity losses less than those found in an earlier study. Values of thrust-to-mass ratio which minimize velocity losses for dual-burn vehicles were found to be significantly greater than the values of thrust-to-launch-mass ratio for the minimum-velocity-loss continuous-burn vehicle. The use of a two-stage solid-propellant vehicle employing a spin-stabilized second stage offers an attractive design option for a Mars surface-to-orbit launch vehicle.

Weaver, W. L.↗
NASA NTRS1987

Sorption compressor/mechanical expander hybrid refrigeration

Experience with Deep Space Network (DSN) ground-based cryogenic refrigerators has proved the reliability of the basic two-stage Gifford-McMahon helium refrigerator. A very long life cryogenic refrigeration system appears possible by combining this expansion system or a turbo expansion system with a hydride sorption compressor in place of the usual motor driven piston compressor. To test the feasibility of this system, a commercial Gifford-McMahon refrigerator was tested using hydrogen gas as the working fluid. Although no attempt was made to optimize the system for hydrogen operation, the refrigerator developed 1.3 W at 30 K and 6.6 W at 60 K. The results of the test and of theoretical performances of the hybrid compressor coupled to these expansion systems are presented.

Jones, J. A.↗
NASA NTRS1987

Recursive inverse kinematics for robot arms via Kalman filtering and Bryson-Frazier smoothing

This paper applies linear filtering and smoothing theory to solve recursively the inverse kinematics problem for serial multilink manipulators. This problem is to find a set of joint angles that achieve a prescribed tip position and/or orientation. A widely applicable numerical search solution is presented. The approach finds the minimum of a generalized distance between the desired and the actual manipulator tip position and/or orientation. Both a first-order steepest-descent gradient search and a second-order Newton-Raphson search are developed. The optimal relaxation factor required for the steepest descent method is computed recursively using an outward/inward procedure similar to those used typically for recursive inverse dynamics calculations. The second-order search requires evaluation of a gradient and an approximate Hessian. A Gauss-Markov approach is used to approximate the Hessian matrix in terms of products of first-order derivatives. This matrix is inverted recursively using a two-stage process of inward Kalman filtering followed by outward smoothing. This two-stage process is analogous to that recently developed by the author to solve by means of spatial filtering and smoothing the forward dynamics problem for serial manipulators.

Rodriguez, G.↗
NASA NTRS1981

Mission options for the first SEPS application

Missions to comets and asteroids are primary candidates for Solar Electric Propulsion System (SEPS) applications. NASA estimates that the first SEPS mission might be launched as early as 1988. This paper presents mission opportunities available for launches between 1988 and early 1991 and discusses the performance capabilities of the current SEPS. Use of a Shuttle Two-Stage IUS and/or a Shuttle Wide Tank Centaur launch vehicle is assumed in the performance assessment. The list of possible first SEPS missions consists of nine missions to comets of primary interest and examples of multiple asteroid rendezvous missions. Both an earth crossing asteroid and a main belt asteroid are considered as first possible targets in the multiple asteroid rendezvous examples. Mission opportunity and performance maps for Eros and Anteros are presented which provide exact performance data and optimal launch and arrival dates for any launch year.

Yen, C.-W. L.↗
NASA NTRS1976

Formulation of a methodology for power circuit design optimization

A methodology for optimizing power-processor designs is described which achieves optimization with respect to some power-processor characteristic deemed particularly desirable by the designer, such as weight or efficiency. Optimization theory based on Lagrange multipliers is reviewed together with nonlinear programming techniques employing penalty functions. The methodology, the task of which is to minimize an objective function subject to design constraints, is demonstrated with the aid of four examples: optimum-weight core selection for an inductor with a predetermined winding size, optimum-weight inductor design with a given loss constraint, optimum-loss inductor design with a given weight constraint, and a comparison of optimum-weight single- and two-stage input-filter designs with identical loss and other requirement constraints. Closed-form solutions for the first three examples are obtained by applying the Lagrange-multiplier method, but solutions for the last example are found numerically through the use of the sequential unconstrained minimization technique.

Yu, Y.↗
NASA NTRS1977

NASA/Pratt and Whitney experimental clean combustor program: Engine test results

A two-stage vorbix (vortex burning and mixing) combustor and associated fuel system components were successfully tested in an experimental JT9D engine at steady-state and transient operating conditions, using ASTM Jet-A fuel. Full-scale JT9D experimental engine tests were conducted in a phase three aircraft experimental clean combustor program. The low-pollution combustor, fuel system, and fuel control concepts were derived from phase one and phase two programs in which several combustor concepts were evaluated, refined, and optimized in a component test rig. Significant pollution reductions were achieved with the combustor which meets the performance, operating, and installation requirements of the engine.

Roberts, R.↗