Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “turbine efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Algorithm for calculating turbine cooling flow and the resulting decrease in turbine efficiency

An algorithm is presented for calculating both the quantity of compressor bleed flow required to cool the turbine and the decrease in turbine efficiency caused by the injection of cooling air into the gas stream. The algorithm, which is intended for an axial flow, air routine in a properly written thermodynamic cycle code. Ten different cooling configurations are available for each row of cooled airfoils in the turbine. Results from the algorithm are substantiated by comparison with flows predicted by major engine manufacturers for given bulk metal temperatures and given cooling configurations. A list of definitions for the terms in the subroutine is presented.

Gauntner, J. W.↗
NASA NTRS1956

Analytical investigation of single-stage-turbine efficiency characteristics in terms of work and speed requirements

This report uses a work-speed parameter in describing single-stage full-admission turbine efficiency characteristics. The range of this parameter considered covers that used in turbojet engine applications as well as that being encountered in such applications as turbopump and accessory drives. Efficiency types considered are (a) total or aerodynamic efficiency, (b) rating efficiency, used in jet enjine applications, and (c) static efficiency, used in turbopump and accessory drive applications. Velocity diagram types considered include zero exit whirl, impulse, and those corresponding to maximum values of efficiency.

Stewart, Warner L↗
NASA NTRS1983

Coolant passage heat transfer with rotation. A progress report on the computational aspects

Turbine airfoils are subjected to increasingly higher heat loads which escalate the cooling requirements in order to satisfy life goals for the component materials. If turbine efficiency is to be maintained, however, cooling requirements should be as low as possible. To keep the quantity of cooling air bounded, a more efficient internal cooling scheme must be developed. One approach is to employ airfoils with multipass cooling passages that contain devices to augment internal heat transfer while limiting pressure drop. Design experience with multipass cooling passage airfoils has shown that a surplus of cooling air must be provided as a margin of safety. This increased cooling air leads to a performance penalty. Reliable methods for predicting the internal thermal and aerodynamic performance of multipass cooling passage airfoils would reduce or eliminate the need for the safety margin of surplus cooling air. The objective of the program is to develop and verify improved analytical methods that will form the basis for design technology which will result in efficient turbine components with improved durability without sacrificing performance. The objective will be met by: (1) establishing a comprehensive experimental data base that can form the basis of an empirical design system; (2) developing computational fluid dynamic techniques; and (3) analyzing the information in the data base with both phenomenological modeling and mathematical modeling to derive a suitable design and analysis procedure.

Aceto, L. D.↗
NASA NTRS1947

Performance Charts for a Turbojet System

Convenient charts are presented for computing the thrust, fuel consumption, and other performance values of a turbojet system. These charts take into account the effects of ram pressure, compressor pressure ratio, ratio of combustion-chamber-outlet temperature to atmospheric temperature, compressor efficiency, turbine efficiency, combustion efficiency, discharge-nozzle coefficient, losses in total pressure in the inlet to the jet-propulsion unit and in the combustion chamber, and variation in specific heats with temperature. The principal performance charts show clearly the effects of the primary variables and correction charts provide the effects of the secondary variables. The performance of illustrative cases of turbojet systems is given. It is shown that maximum thrust per unit mass rate of air flow occurs at a lower compressor pressure ratio than minimum specific fuel consumption. The thrust per unit mass rate of air flow increases as the combustion-chamber discharge temperature increases. For minimum specific fuel consumption, however, an optimum combustion-chamber discharge temperature exists, which in some cases may be less than the limiting temperature imposed by the strength temperature characteristics of present materials.

CHARTS-PERFORMANCE-ENGINES, TURBOJET↗
NASA NTRS1949

Effect of Air Cooling of Turbine Disk on Power and Efficiency of Turbine from Turbo Engineering Corporation TT13-18 Turbosupercharger.

An investigation was conducted to determine the effect of turbine-disk cooling with air on the efficiency and the power output of the radial-flow turbine from the Turbo Engineering Corporation TT13-18 turbosupercharger. The turbine was operated at a constant range of ratios of turbine-inlet total pressure to turbine-outlet static pressure of 1,5 and 2.0, turbine-inlet total pressure of 30 inches mercury absolute, turbine-inlet total temperature of 12000 to 20000 R, and rotor speeds of 6000 to 22,000 rpm, Over the normal operating range of the turbine, varying the corrected cooling-air weight flow from approximately 0,30 to 0.75 pound per second produced no measurable effect on the corrected turbine shaft horsepower or the turbine shaft adiabatic efficiency. Varying the turbine-inlet total temperature from 12000 to 20000 R caused no measurable change in the corrected cooling-air weight flow. Calculations indicated that the cooling-air pumping power in the disk passages was small and was within the limits of the accuracy of the power measurements. For high turbine power output, the power loss to the compressor for compressing the cooling air was approximately 3 percent of the total turbine shaft horsepower.

Berkey, William E.↗
NASA NTRS2000

Experimental and Numerical Investigation of Losses in Low-Pressure Turbine Blade Rows

Experimental data and numerical simulations of low-pressure turbines have shown that unsteady blade row interactions and separation can have a significant impact on the turbine efficiency. Measured turbine efficiencies at takeoff can be as much as two points higher than those at cruise conditions. Several recent studies have revealed that the performance of low-pressure turbine blades is a strong function of the Reynolds number. In the current investigation, experiments and simulations have been performed to study the behavior of a low-pressure turbine blade at several Reynolds numbers. Both the predicted and experimental results indicate increased cascade losses as the Reynolds number is reduced to the values associated with aircraft cruise conditions. In addition, both sets of data show that tripping the boundary layer helps reduce the losses at lower Reynolds numbers. Overall, the predicted aerodynamic and performance results exhibit fair agreement with experimental data.

Dorney, Daniel J.↗
NASA NTRS1951

Comparison of measured efficiencies of nine turbine designs with efficiencies predicted by two empirical methods

Empirical methods of Ainley and Kochendorfer and Nettles were used to predict performances of nine turbine designs. Measured and predicted performances were compared. Appropriate values of blade-loss parameter were determined for the method of Kochendorfer and Nettles. The measured design-point efficiencies were lower than predicted by as much as 0.09 (Ainley and 0.07 (Kochendorfer and Nettles). For the method of Kochendorfer and Nettles, appropriate values of blade-loss parameter ranged from 0.63 to 0.87 and the off-design performance was accurately predicted.

FLOW-TURBINES↗
NASA NTRS1948

Altitude-Wind-Tunnel Investigation of a 4000-Pound-Thrust Axial-Flow Turbojet Engine: Analysis of Turbine Performance - 5

Performance characteristics of the turbine of a 4000-pound-thrust axial-flow turbojet engine was determined in investigations of the complete engine in the NACA Cleveland altitude wind tunnel. Characteristics are presented as functions of the total-pressure ratio across the turbine and of turbine speed and gas flow corrected to sea-level conditions. Three turbine nozzles of different areas were used to determine the area that gave optimum performance. Inasmuch as tail-pipe nozzles of different diameters were investigated in combination with the standard turbine nozzle, the effect of varying discharge conditions on turbine operation could be observed. The investigations covered a range of pressure attitudes from 5000 to 40,000 feet. The engine was investigated over the entire operable range of speeds at each altitude. At pressure altitude of 30,000 feet, the effect on turbine operation of varying the ram pressure ration over a range from 1.10 to 1.77 was evaluated. An altitude effect was apparent when turbine pressure ratio was plotted against corrected turbine speed but it was so slight as to be negligible insofar as the turbine efficiencies were concerned. A maximum turbine efficiency of slightly more than 82 percent was obtained with the configuration using the standard turbine nozzle and the low-flow compressor. This efficiency, which is somewhat lower than the actual turbine efficiency, is uncorrected for accessories drive power, bearing friction, tail-pipe pressure drop, compressor thermal radiation, and introduction of turbine-disk cooling air into the gas stream. Changes in the ram pressure ratio had a negligible effect on the turbine efficiency.

Krebs, Richard P.↗
NASA NTRS1960

Analytical Investigation of Cycle Characteristics for Advanced Turboelectric Space Power Systems

An investigation was made of the relative influence of turbine inlet temperature, radiator temperature, and turbine efficiency on radiator area for Rankine cycles with rubidium, potassium, and sodium as working fluids. It was determined that, whereas turbine inlet temperature and turbine efficiency have gross effects on radiator size for a given inlet temperature a considerable latitude in the selection of radiator temperature may be accepted with only minor effects on required radiator size. Also investigated was the influence on turbine efficiency and design of the factors that distinguish alkali-metal vapor turbines from conventional gas turbines. The turbine configuration was determined to be a function of the involved working fluids and rotor blade speed. For a given blade speed, the number of stages required for high turbine efficiency was found to vary directly with turbine specific work output, and therefore to vary in the ratio 5 to 2.5 to 1 for sodium, potassium, and rubidium, respectively. Lower blade speeds than employed in conventional gas turbines may be required to satisfy critical stress considerations resulting from the elevated temperatures involved and the criterion of long-duration reliability. This will increase the number of turbine stages necessary to obtain high turbine efficiency and consequently increase turbine weight. The question of moisture formation was discussed and a calculation was made to indicate the nature of the aerodynamic losses due to moisture content. Various means of reducing moisture content were considered, including mechanical removal, increased radiator temperature, inefficient expansion, superheat, and reheat. Sample calculations were made in most cases to indicate their comparative effectiveness and resultant penalty in required radiator area.

Moffitt, Thomas P.↗
NASA NTRS1971

Preliminary performance of a 4.97-inch radial turbine operating in a Brayton power system with a helium-xenon gas mixture

The performance characteristics of the Brayton-rotating-unit's 4.97-inch radial turbine were investigated with the turbine part of a power conversion system. The following system parameters were varied: turbine inlet temperature from 1200 to 1600 F, compressor inlet temperature from 60 to 120 F, compressor outlet pressure from 20 to 45 psia, and shaft speed from 90-110 percent of rated speed (36000 rpm). The working fluid of the system was a gas mixture of helium-xenon with a nominal molecular weight of 83.8. Test results indicate that changes in system conditions have little effect on the turbine efficiency. At the design turbine inlet temperature of 1600 F and compressor inlet temperature of 80 F, an average turbine efficiency of 91 percent was obtained.

Leroy, M. J., Jr.↗
NASA NTRS2020

Proceedings of the 2010 NASA-Industry Low Pressure Turbine and Power Turbine (LPT/PT) Efficiency Improvement Workshop

This report includes materials from the NASA-Industry Low Pressure Turbine and Power Turbine (LPT/PT) Efficiency Improvement Workshop that took place on August 10 and 11, 2010, at the NASA Glenn Research Center. The materials include all the presentation slides and a workshop summary article that provides background information, describes the workshop motivation, and provides a summary of the open discussions that took place. Participation included specialists from academia, government laboratories, and industry, from the United States and abroad. The workshop was motivated by underperformance of large commercial engines related to lower-than-expected efficiency of the LPT. It focused on addressing the relevant flow physics. Recommendations were made for continued research. The main recommendation was to conduct rotating rig tests accompanied by the study of fundamental mechanism using computational fluid dynamics (CFD) and turbulence and transition model development.

Transition↗