Large-amplitude pulse propagation - A transient effect
Transient signal generation during large amplitude ultrasonic pulse propagation through carbon tetrachloride
Beyer, R. T.↗
SEARCH · Engineering Papers
Results for “transient effects”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Large-amplitude pulse propagation - A transient effect. II
Transient signal generation by propagation of large amplitude pulses, discussing angular dependence in water
Beyer, R. T.↗
Effects of shunt capacitance on transient effects caused by electron irradiation of a polyethylene terephthalate insulated ribbon wire
External shunt capacitance effects upon electron irradiation induced voltage pulses from polyethylene terephthalate insulated ribbon wire
CAPACITANCE↗
Beam-Switch Transient Effects in the RF Path of the ICAPA Receive Phased Array Antenna
When the beam of a Phased Array Antenna (PAA) is switched from one pointing direction to another, transient effects in the RF path of the antenna are observed. Testing described in the report has revealed implementation-specific transient effects in the RF channel that are associated with digital clocking pulses that occur with transfer of data from the Beam Steering Controller (BSC) to the digital electronics of the PAA under test. The testing described here provides an initial assessment of the beam-switch phenomena by digitally acquiring time series of the RF communications channel, under CW excitation, during the period of time that the beam switch transient occurs. Effects are analyzed using time-frequency distributions and instantaneous frequency estimation techniques. The results of tests conducted with CW excitation supports further Bit-Error-Rate (BER) testing of the PAA communication channel.
Sands, O. Scott↗
Radiation-Induced Transient Effects in Near Infrared Focal Plane Arrays
This viewgraph presentation describes a test simulate the transient effects of cosmic ray impacts on near infrared focal plane arrays. The objectives of the test are to: 1) Characterize proton single events as function of energy and angle of incidence; 2) Measure charge spread (crosstalk) to adjacent pixels; 3) Assess transient recovery time.
Reed, Robert A.↗
CSR induced microbunching gain estimation including transient effects in transport and recirculation arcs
The coherent synchrotron radiation (CSR) of a high brightness electron beam traversing a series of dipoles, such as transport or recirculation arcs, may result in the microbunching instability (μBI). To accurately quantify the direct consequence of this effect, we further extend our previously developed semi-analytical Vlasov solver to include more relevant coherent radiation models than the steady-state free-space CSR impedance, such as the entrance and exit transient effects derived from upstream beam entering to and exiting from individual dipoles. The resultant microbunching gain functions and spectra for our example lattices are presented and compared with particle tracking simulation. Some underlying physics with inclusion of these effects are also discussed.
43 PARTICLE ACCELERATORS↗
Sensitivity analysis of in-pile critical heat flux experiments in TREAT for characterization of RIA power-transient effects
A reactivity-initiated accident (RIA) is one type of postulated design basis accident (DBA) that can cause a departure from nucleate boiling (DNB) event in pressurized-water reactors (PWRs). A DNB occurrence and its consequences depend on the thermophysical properties of the fuel components and coolant, characteristics of the transient energy insertion into the fuel rod, and the onset of the critical heat flux (CHF) phenomenon. To leverage the restart of the Transient Reactor Test (TREAT) Facility, an effort is currently underway to better understand the cladding-to-coolant heat transfer mechanisms and the CHF phenomenon under fast-transient irradiation conditions. This paper characterizes the impact of power transients on the thermal-hydraulic behavior of a TREAT Facility reactor heater rodlet CHF experiment to provide the priority of parameters that need to be investigated for an improved CHF model. Sobol sensitivity analysis methods and the Reactor Excursion and Leak Analysis Program (RELAP5-3D) code were used to identify key input parameters on the uncertainty in the prediction of peak outer- and inner-surface temperatures of the heater tube, as well as the time of the DNB event. A series of sensitivity analyses revealed the total energy deposition on the tube and the transient effects of power pulse had large impacts on the maximum temperatures. The CHF multiplier had the largest impact on the time occurrence of CHF. The overall results show the energy deposition rate in the tube is the most influencing factor to the manifestation of CHF and the resulting thermal-hydraulic behaviors of the tube. The multiplier for the CHF, which is interpreted as the predicted CHF value, has the largest Sobol indices for the time of the CHF in all cases, since it directly determines the occurrence of CHF. It is inferred that the uncertainties in the thermal-hydraulic behaviors of fuels increase with respect to the key parameters as the power pulse becomes broader, and an accurate estimation of the energy deposition rate is required to reduce the uncertainty in the evaluation of the integrity of fuel if the CHF is expected to occur near the peak power. Therefore, the outputs are expected to provide rigorous interpretation of ongoing in-pile CHF experiments in the TREAT Facility reactor regarding thermal-hydraulic behavior of the fuel system aiming for a new transient in-pile CHF model.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Structure formation in perfluoropentacene:diindenoperylene blends and its impact on transient effects in the optical properties studied in real-time during growth
We discuss the result of the competing effects of favourable intermolecular interactions and steric incompatibilities due to the size mismatch of perfluoropentacene (PFP) and diindenoperylene (DIP) on the structure formation and associated optical properties in mixed films. Using real-time grazing incidence X-ray diffraction we investigate the size of coherently scattering islands l{sub s} as a function of film thickness and mixing ratio. We find that for PFP:DIP 1:2 blends l{sub s} is by a factor of ∼4 smaller than in pure DIP films, while l{sub s} of the PFP:DIP 2:1 blends is not significantly reduced compared with pure PFP. Yet, we observe an increase in l{sub s} with film thickness for all of the samples, independent on the mixing ratio. In parallel with the structural characterization we investigate the evolution of the absorption spectra in the visible spectral range and its dependence on l{sub s} in situ during film growth using differential reflectance spectroscopy. We observe a surprisingly strong effect of changes in the structural order on the shape of ε{sub 2,} {sub xy}(E), evident by a pronounced evolution of characteristic peaks in the thickness range from 1.6 nm to 9.6 nm. The combined results of the real-time experiments allow to identify the thickness dependent crystal grain size as the origin of the observed transient effects in the absorption spectra.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Transient effect of lubricant on elastohydro-dynamic film thickness
The inlet solution of the elastohydrodynamic lubricated rolling contact problem was obtained by considering lubricants with transient viscosity. The effect of the viscoelastic retardation time of the lubricant on the center film thickness was investigated. The effect of transient viscosity in response to a sudden pressure was found to be insignificant in determining the film thickness in elastohydrodynamic contacts.
Wang, K. L.↗
Studies of photoconductivity and field effect transistor behavior in examining drift mobility, surface depletion, and transient effects in Si-doped GaN nanowires in vacuum and air
Variable intensity photoconductivity (PC) performed under vacuum at 325 nm was used to estimate drift mobility ({mu}) and density ({sigma}{sub s}) of negative surface charge for c-axis oriented Si-doped GaN nanowires (NWs). In this approach, we assumed that {sigma}{sub s} was responsible for the equilibrium surface band bending ( Empty-Set ) and surface depletion in the absence of illumination. The NWs were grown by molecular beam epitaxy to a length of approximately 10 {mu}m and exhibited negligible taper. The free carrier concentration (N) was separately measured using Raman scattering which yielded N = (2.5 {+-} 0.3) Multiplication-Sign 10{sup 17} cm{sup -3} for the growth batch studied under 325 nm excitation. Saturation of the PC was interpreted as a flatband condition whereby Empty-Set was eliminated via the injection of photogenerated holes. Measurements of dark and saturated photocurrents, N, NW dimensions, and dimensional uncertainties, were used as input to a temperature-dependent cylindrical Poisson equation based model, yielding {sigma}{sub s} in the range of (3.5 to 7.5) Multiplication-Sign 10{sup 11} cm{sup -2} and {mu} in the range of (850 to 2100) cm{sup 2}/(V s) across the (75 to 194) nm span of individual NW diameters examined. Data illustrating the spectral dependence and polarization dependence of the PC are also presented. Back-gating these devices, and devices from other growth batches, as field effect transistors (FETs) was found to not be a reliable means to estimate transport parameters (e.g., {mu} and {sigma}{sub s}) due to long-term current drift. The current drift was ascribed to screening of the FET back gate by injected positive charge. We describe how these gate charging effects can be exploited as a means to hasten the otherwise long recovery time of NW devices used as photoconductive detectors. Additionally, we present data illustrating comparative drift effects under vacuum, room air, and dry air for both back-gated NW FETs and top-gated NW MESFETs.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Transient Effects in Atmosphere and Ionosphere Preceding the 2015 M7.8 and M7.3 Gorkha–Nepal Earthquakes
We analyze retrospectively/prospectively the transient variations of six different physical parameters in the atmosphere/ionosphere during the M7.8 and M7.3 earthquakes in Nepal, namely: 1) outgoing longwave radiation (OLR) at the top of the atmosphere (TOA); 2) GPS/TEC; 3) the very-low-frequency (VLF/LF) signals at the receiving stations in Bishkek (Kyrgyzstan) and Varanasi (India); 4) Radon observations; 5) Atmospheric chemical potential from assimilation models; and; 6) Air Temperature from NOAA ground stations. We found that in mid-March 2015, there was a rapid increase in the radiation from the atmosphere observed by satellites. This anomaly was located close to the future M7.8 epicenter and reached a maximum on April 21–22. The GPS/TEC data analysis indicated an increase and variation in electron density, reaching a maximum value during April 22–24. A strong negative TEC anomaly in the crest of EIA (Equatorial Ionospheric Anomaly) occurred on April 21, and a strong positive anomaly was recorded on April 24, 2015. The behavior of VLF-LF waves along NWC-Bishkek and JJY-Varanasi paths has shown abnormal behavior during April 21–23, several days before the first, stronger earthquake. Our continuous satellite OLR analysis revealed this new strong anomaly on May 3, which was why we anticipated another major event in the area. On May 12, 2015, an M7.3 earthquake occurred. Our results show coherence between the appearance of these pre-earthquake transient’s effects in the atmosphere and ionosphere (with a short time-lag, from hours up to a few days) and the occurrence of the 2015 M7.8 and M7.3 events. The spatial characteristics of the pre-earthquake anomalies were associated with a large area but inside the preparation region estimated by Dobrovolsky-Bowman. The preearthquake nature of the signals in the atmosphere and ionosphere was revealed by simultaneous analysis of satellite, GPS/TEC, and VLF/LF and suggest that they follow a general temporal-spatial evolution pattern that has been seen in other large earthquakes worldwide
Dimitar Ouzounov↗
Transient Effects in Planar Solidification of Dilute Binary Alloys
The initial transient during planar solidification of dilute binary alloys is studied in the framework of the boundary integral method that leads to the non-linear Volterra integral governing equation. An analytical solution of this equation is obtained for the case of a constant growth rate which constitutes the well-known Tiller's formula for the solute transient. The more physically relevant, constant ramping down temperature case has been studied both numerically and analytically. In particular, an asymptotic analytical solution is obtained for the initial transient behavior. A numerical technique to solve the non-linear Volterra equation is developed and the solution is obtained for a family of the governing parameters. For the rapid solidification condition, growth rate spikes have been observed even for the infinite kinetics model. When recirculating fluid flow is included into the analysis, the spike feature is dramatically diminished. Finally, we have investigated planar solidification with a fluctuating temperature field as a possible mechanism for frequently observed solute trapping bands.
Mazuruk, K.↗
Transient Effects in Planar Solidification of Dilute Binary Alloys
The initial transient during planar solidification of dilute binary alloys is studied in the framework of the boundary integral method that leads to the non-linear Volterra integral governing equation. An analytical solution of this equation is obtained for the case of a constant growth rate which constitutes the well-known Tiller's formula for the solute transient. The more physically relevant, constant ramping down temperature case has been studied both numerically and analytically. In particular, an asymptotic analytical solution is obtained for the initial transient behavior. A numerical technique to solve the non-linear Volterra equation is developed and the solution is obtained for a family of the governing parameters. For the rapid solidification condition, growth rate spikes have been observed even for the infinite kinetics model. When recirculating fluid flow is included into the analysis, the spike feature is dramatically diminished. Finally, we have investigated planar solidification with a fluctuating temperature field as a possible mechanism for frequently observed solute trapping bands.
Mazuruk, Konstantin↗
An analytical investigation of transient effects on rewetting of heated thin flat plates
The rewetting of a hot surface is a problem of prime importance in the microgravity application of heat pipe technology, where rewetting controls the time before operations can be re-established following depriming of a heat pipe. Rewetting is also important in the nuclear industry (in predicting behavior during loss-of-coolant accidents), as well as in the chemical and petrochemical industries. Recently Chan and Zhang have presented a closed-form solution for the determination of the rewetting speed of a liquid film flowing over a finite (but long) hot plate subject to uniform heating. Unfortunately, their physically unreasonable initial conditions preclude a meaningful analysis of start-up transient behavior. A new nondimensionalization and closed-form solution for an infinitely-long, uniformly-heated plate is presented. Realistic initial conditions (step change in temperature across the wetting front) and boundary conditions (no spatial temperature gradients infinitely far from the wetting front) are employed. The effects of parametric variation on the resulting simpler closed-form solution are presented and compared with the predictions of a 'quasi-steady' model. The time to reach steady-state rewetting is found to be a strong function of the initial dry-region plate temperature. For heated plates it is found that in most cases the effect of the transient response terms cannot be neglected, even for large times.
Platt, J. A.↗
Near contact phenomena and transient effects in far infrared photoconductors
A combination of experimental and modeling work is summarized in two areas: first, the calculation of excess free carrier and space charge distributions near contacts and their effects on device resistivity, and second, the characterization of a slow transient response (tau approx. 1 sec) in Ge:Be detectors which is due to trapping associated with Be(+) formation. In both cases, analytical models, based on continuity and rate equations, have been developed to enable the application of these findings to a wide variety of photoconductor materials.
Haegel, Nancy M.↗
An investigation of thermal transient effects in a displacement metering apparatus.
Remote flow metering error due to mass accumulation from thermal expansion of incompressible fluid, analyzing transient temperature distribution in finite duct
Wrobel, J. R.↗
Developing Separate Effects Transient Test Experiments Using an Out-of-Pile Flowing Water Loop
In 2017 the Transient Reactor Test Facility was restarted after being placed in a standby state since 1994. This Test Reactor’s restart has since enabled the progressive development of new nuclear technologies within the U.S. that were previously required to outsource to other countries. While the reactor’s restart was a large feat worthy of recognition, the experimental use of its characteristics has required the further development of in-pile experimental infrastructure sufficient to support programmatic needs. This hardware have taken the form of capsule designs (compact and elongated) as well as loop concepts representing the phenomena of interest for a subset of separate effects tests desire for each respective testing campaign. The Transient Testing Program has a large-integrated effort that aligns with the U.S. Department of Energy’s current needs. This study compliments those programmatic elements by developing, fabricating and demonstrating a full-scale flowing water loop in an out-of-pile environment. The goal of this effort is to develop a pragmatic understanding of the engineering capabilities and limitations associated with geometric form-factors, metering technology, and controls logic under representative thermal hydraulic conditions that would be experienced within the TREAT reactor during an in-pile reactivity initiated accident test. The outcomes of this study result in an evaluation of the conceptual design of a comprehensive flowing water loop including objective figures of merit (FoMs) for comparing unique instrumentation and the basis for their selection during operations. These efforts directly contribute to and are required for the further advancement of transient testing capabilities within the U.S.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
How transient effects can change the inferred plasma temperatures when using K-shell sulfur line ratios in a time dependent iron sulfide plasma
This paper describes how the steady state atomic kinetics approximation can underestimate the electron temperature determined from K-shell lines in ps-time-scale transient plasmas. In particular, we model the temperature determination of solid FeS targets used in opacity experiments at the Orion laser facility from the ratio of sulfur He-α to Ly-α lines. Such experiments use short-pulse lasers to heat a thin microdot of FeS buried in a plastic target to temperatures of more than 1 keV and densities of approximately 1–2 g/cm 3 . Using atomic kinetics calculations based on a temperature history from a radiation hydrodynamic simulation of the target evolution, the peak temperature inferred from the sulfur line ratios is 1.29 keV at 3.1 ps as compared with the input peak temperature of 1.41 keV at 2.0 ps. There is a time lag of 1.2 ps at the peak, and an overall 0.5 ps time lag in the temporal history of the temperature as the plasma cools over the next 10 ps.
Rilloraza, Francisco↗