Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal modeling techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Modeling of thermal pressurization in tight claystone using sequential THM coupling: Benchmarking and validation against in-situ heating experiments in COx claystone

We apply thermoporoelasticity and a sequentially coupling technique for modeling thermally-driven coupled Thermo-Hydro-Mechanical (THM) processes in tight claystone. A THM benchmark case with a corresponding analytic solution for thermoporoelasticity under a constant heat loading verifies the model. Thereafter, two in situ heating experiments are simulated for model validation: a smaller-scale heating experiment (TED experiment) and a larger-scale experiment (ALC experiment) in Callovo-Oxfordian (COx) claystone at the Meuse/Haute-Marne underground research laboratory in France. The model exhibits good performance to match the observed temperature and pore pressure evolution for the smaller-scale TED experiment. For the larger-scale ALC experiment, general trends of thermal-pressurization are captured in the modeling, but pressure is underestimated at some monitoring points during cool-down. This indicates that the THM response in the field may be affected by the variability of rock's properties or irreversible or time-dependent mechanical processes that are not included in the current thermoporoelastic model. The main contributions of this work are as follows: (1) we verify and validate the numerical simulator, TOUGH-FLAC, to be a valuable coupled THM modeling tool; (2) prove that the laboratory determined material parameters can be used as reference values for upscaling experiments. However, to better identify and quantify THM processes with modeling of in situ tests, more emphasize should be dedicated to obtaining high-quality mechanical deformation data.

58 GEOSCIENCES↗
DOE OSTI2025

Design of an Out-Of-Pile Experimental Facility to Demonstrate the Feasibility of In Situ Thermal Conductivity Measurements of Nuclear Fuels Under Irradiation

There is substantial merit in quantifying nuclear fuel performance under irradiation. At Oak Ridge National Laboratory (ORNL), the MiniFuel irradiation platform has become the primary test vehicle for conducting separate-effects fuel performance irradiation experiments. The MiniFuel experiment is a passively controlled capsule design deployed in the High Flux Isotope Reactor (HFIR) through which fuel performance data is collected post-irradiation. Separate effects fuels irradiation capabilities are being expanded at ORNL by developing instrumented capsule designs that aim to capture fuel performance phenomena in-situ. One such capsule will specifically target fuel specimen thermal conductivity changes as a function of fuel burnup. Due to the complexity of making this measurement on nuclear fuel in-pile, this paper describes the necessary out-of-pile testing conducted on the thermal conductivity capsule (TCC) design. The measurement is ascertained via a thermopile system with heat transferred unidirectionally through a surrogate fuel specimen sandwiched between two conductive materials. The capsules investigated in this study are representative of the in-pile design, with the primary departure from irradiation conditions being the distribution of heat generation within the capsule. In the out-of-pile experiment, an external heater was used to drive heat through the conductive slug materials and into the specimen. This paper expounds the design of the out-of-pile experimental system and the thermal conductivity measurement technique. Predictive models used to determine the sensitivity of the measurement to variables governing thermal contact conductance between the specimen and slug materials and to predict experimental results are also described. Data from the out-of-pile experiment will be used to validate the readiness of the design for insertion into HFIR for irradiation.

Parker, Trevor [ORNL]↗
DOE OSTI2025

Deviations from the Porter-Thomas Distribution due to Nonstatistical 𝛾 Decay below the 150 Nd Neutron Separation Threshold

We introduce a new method for the study of fluctuations of partial transition widths based on nuclear resonance fluorescence experiments with quasimonochromatic linearly polarized photon beams below particle separation thresholds. It is based on the average branching of decays of 𝐽=1 states of an even-even nucleus to the 2$^{+}_{1}$ state in comparison to the ground state. Between 5 and 7 MeV, a constant average branching ratio for 𝛾 decays from 1 − states of 0.490(16) is observed for the nuclide 150 Nd. Assuming 𝜒 2 -distributed partial transition widths, this average branching ratio is related to a degree of freedom of 𝜈 = 1.93⁢(12), rejecting the validity of the Porter-Thomas distribution, requiring 𝜈 = 1. The observed deviation can be explained by nonstatistical effects in the 𝛾-decay behavior with contributions in the range of 9.4(10)% up to 94(10)%.

150 ≤ A ≤ 189↗
DOE OSTI2020

Multi-Scale Thermal Analysis for Design of SiC-Based Medium Voltage Motor Drive: Preprint

This paper describes a multi-scale thermal analysis approach for the design of an air-cooled 1.7-kV SiC MOSFET-based medium-voltage variable-speed motor drive. The National Renewable Energy Laboratory supported the project objectives by providing thermal management design support to the project partner The Ohio State University (OSU). The scope of the models and limited resources required efficient and flexible thermal models to be developed. Two modeling techniques are described that significantly reduced model run time and enabled more complex models to be run faster while retaining needed accuracy. The first technique uses the effectiveness-NTU method to extract convection boundary conditions from a computational fluid dynamics (CFD) model that can be applied to a fast-running finite element analysis model. The second is a porous media technique that enables system-level CFD simulations that incorporate effects from heat exchangers (e.g., pin fin heat sinks) that run in a fraction of the time required for fully resolved CFD simulations. The multi-scale approach to the thermal analysis enabled fast and accurate simulation for the converter design ranging from the die level up to the full system with 36 submodules. The modeling results were validated against experimental data from system tests performed by OSU.

DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Comparison of plug flow and multi-node stratified tank modeling approaches regarding computational efficiency and accuracy

Residential water heaters contain water stratified by temperature-driven density differences. This implies that a water tank can reach a state in which the top and bottom sections have different temperatures, unless mixing happens. A high degree of thermal stratification can improve the efficiency of some water heaters, by saving the amount of energy required for the heat-up process. Studies of stratification became popular in the 1970s and it remains an active research topic today. The research has led to the development of different models and techniques to better predict and define a stratified tanks behavior. By comparing these models and techniques used previously to describe thermal stratification, the phenomenon could be better understood, exploited, and used to increase efficiency and thermal energy capacity in modern water tanks. From the existing models, we found the one-dimensional standard plug-flow and a multi node model to be appropriate for analyzing the processes of the heat up and cool-down in a water tank. These two models are based on energy balances. This work involved comparing the accuracy and computational effort needed to implement these models. To assess accuracy, we compared both types of existing models to experimental data (also collected in this work) which included a heat up process using an external heat pump. This external process included a layering process that has an eddy diffusivity at five times the rate of thermal diffusion. For this project, we implemented the models in MATLAB, the multi-paradigm numerical computing environment. We quantified model accuracy using the root mean squared error between modeled data and experimental data for six measured tank temperatures. Comparing the accuracy and the computational time taken to run the simulation provides a method to contrast the performance of each model and a way to rate it. The multi node model was run using from 6 to 96 spatial nodes; the plug flow model was run using 1 to 0.001 º C temperature bin sizes. Additionally, timesteps were varied from 4 to 236 s. The results quantify the tradeoff between accuracy and computational time, providing guidance for simulations to intelligently select the best model type and simulation parameters. This research can be used to validate the pre-existing models and possibly improve the modern water tank.

Bulnes, Fernando Karg↗
DOE OSTI2023

Microgrid Tiered Circuits Effects for a Planned Housing Community in Puerto Rico

Puerto Rico faced a double strike from hurricanes Irma and Maria in 2017. The resulting damage required a comprehensive rebuild of electric infrastructure. There are plans and pilot projects to rebuild with microgrids to increase resilience. This paper provides a techno-economic analysis technique and case study of a potential future community in Puerto Rico that combines probabilistic microgrid design analysis with tiered circuits in building energy modeling. Tiered circuits in buildings allow electric load reduction via remote disconnection of non-critical circuits during an emergency. When coupled to a microgrid, tiered circuitry can reduce the chances of a microgrid's storage and generation resources being depleted. The analysis technique is applied to show 1) Approximate cost savings due to a tiered circuit structure and 2) Approximate cost savings gained by simultaneously considering resilience and sustainability constraints in the microgrid optimization. The analysis technique uses a resistive capacitive thermal model with load profiles for four tiers (tier 1-3 and non-critical loads). Three analyses were conducted using: 1) open-source software called Tiered Energy in Buildings and 2) the Microgrid Design Toolkit. For a fossil fuel based microgrid 30% of the total microgrid costs of 1.18 million USD were calculated where the non-tiered case keeps all loads 99.9% available and the tiered case keeps tier 1 at 99.9%, tier 2 at 95%, tier 3 at 80% availability, with no requirement on non-critical loads. The same comparison for a sustainable microgrid showed 8% cost savings on a 5.10 million USD microgrid due to tiered circuits. The results also showed 6-7% cost savings when our analysis technique optimizes sustainability and resilience simultaneously in comparison to doing microgrid resilience analysis and renewables net present value analysis independently. Though highly specific to our case study, similar assessments using our analysis technique can elucidate value of tiered circuits and simultaneous consideration of sustainability and resilience in other locations.

building energy modeling↗
DOE OSTI2025

Vector-level feedforward control of LPBF melt pool area using a physics-based thermal model

Laser powder bed fusion (LPBF) is an additive manufacturing technique that has gained popularity thanks to its ability to produce geometrically complex, fully dense metal parts. However, these parts are prone to internal defects and geometric inaccuracies, stemming in part from variations in the melt pool. Here, this paper proposes a novel vector-level feedforward control framework for regulating melt pool area in LPBF. By decoupling part-scale thermal behavior from small-scale melt pool physics, the controller provides a scale-agnostic prediction of melt pool area and efficient optimization over it. This is done by operating on two coupled lightweight models: a finite-difference thermal model that efficiently captures vector-level temperature fields and a reduced-order, analytical melt pool model. Each model is calibrated separately with minimal single-track and 2D experiments, and the framework is validated on a complex 3D geometry in both Inconel 718 and 316L stainless steel. Results showed that feedforward vector-level laser power scheduling reduced geometric inaccuracy in key dimensions by 62%, overall porosity by 16.5%, and photodiode root-mean-squared deviation by 38.5% on average. Overall, this modular, data-efficient approach demonstrates that proactively compensating for known thermal effects can significantly improve part quality while remaining computationally efficient and readily extensible to other materials and machines.

Additive manufacturing↗
DOE OSTI2021

Operating a commercial building HVAC load as a virtual battery through airflow control

Virtual battery (VB) is an innovative method to model flexibility of building loads and effectively coordinate them with other resources at a system level. Unlike a real battery with a dedicated power conversion system for charging control, methods are required for operating building loads to deviate from the baseline to respond to grid signals. This paper presents a VB control for a commercial heating, ventilation, and air conditioning (HVAC) system to follow the desired power consumption in real-time by adjusting zonal airflow rates. The proposed method consists of two parts. At the system level, a mixed feedforward and feedback control is used to estimate the desired total airflow rate. At the zone level, two priority-based algorithms are then proposed to distribute the total airflow rate to individual zones. In particular, a zonal airflow limit estimation method is proposed using machine-learning techniques, in contrast to physics-based thermal models in existing studies, to more accurately capture zonal thermal dynamics and improve temperature control performance. An office building on the Pacific Northwest National Laboratory campus is implemented in EnergyPlus, and used to illustrate and validate the proposed control.

Wang, Jiyu↗
DOE OSTI2022

Mesoscale modeling of microstructure-dependent thermal conductivity in U-Zr fuels

In uranium-zirconium (U-Zr) based metallic fuels, different phases can form at different compositions and temperatures. Typically, lamellar δ-UZr 2 and α-U phases are the dominant microstructures in U-rich U-Zr alloys at temperatures below 880 K. In this work, a finite element method based mesoscale modeling technique is used to calculate the effective thermal conductivities of such heterogeneous microstructures, using the thermal conductivities of two individual phases and their interphase thermal resistance (Kapitza resistance) as input parameters. The Kapitza resistance between δ-UZr 2 and α-U is determined at different temperatures, which shows an approximately T 3 dependence in the temperature range between 300 and 800 K. In addition, the Kapitza resistance exhibits a strong dependence on the aspect ratio of the δ-UZr 2 phase. Further, an analytical model is therefore developed to quantify the effects of both temperature and δ-UZr 2 aspect ratio on the Kapitza resistance. Using this newly developed Kapitza resistance model, the effective thermal conductivities of a number of δ-UZr 2 + α-U heterogeneous microstructures in U-Zr alloys, including non-lamellar microstructures, can be estimated accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Simulations of SITI Cookoff Experiments Carried Out with Different Lots of PBX 9502

A pressure dependent cookoff model for PBX 9502 was developed by Hobbs’ et. al. PBX 9502 is composed of 95% by mass triaminotrinitrobenzene (TATB) and a 5% by mass chlorotrifluoroethylene/vinylidine fluoride binder. The objective in this study is to implement this cookoff model in Aria to simulate Sandia Instrumented Thermal Ignition (SITI) experiments that were carried out with different manufacturing lots of PBX 9502. The SITI design consists of solid cylinders (1" diameter × 1" height) of insensitive high explosive (IHE) confined by a cylindrical aluminum case. An electric heater is wrapped around the lateral surface of the case. This heater produces a temperature heating ramp on the outer surface of the case. Internal thermocouples measure the IHE temperature rise from the center to locations close to the IHE-aluminum interface. The energetic material is heated until thermal ignition occurs. Pressure is measured with a static pressure transducer installed on top of the confinement case. Two–dimensional axisymmetric heat conduction finite element models were implemented to simulate these experiments using four options of the PBX 9502 cookoff model. In addition, the predictive ability of this thermal decomposition model is evaluated using Latin Hypercube Sampling (LHS) techniques.

42 ENGINEERING↗
DOE OSTI2024

Multitarget control models for building thermal comfort and indoor air quality - A critical review

The control techniques in buildings contribute significantly to thermal comfort and indoor air quality (IAQ). However, the gaps are existing for multitarget controls considering both thermal comfort and IAQ. They are: (1) both experimental and modeling control studies were conducted for thermal comfort, focusing on temperature and humidity. (2) All three (physical, grey-box, black-box) modeling approaches were investigated for temperature control. (3) Physical and grey-box modeling approach were adopted for humidity control. (4) physical models were developed for VOCs and CO2 control. (5) grey-box and black-box models were lacking for VOCs and CO2. (6) Multi-target controls were lacking for temperature, humidity and CO2s. (7) Limited studies are available for multi-target controls for temperature, humidity, and VOCs. (8) Multi-target controls are not available yet for temperature, humidity, VOCs, and CO2.

42 ENGINEERING↗
DOE OSTI2023

Grey-box and ANN-based building models for multistep-ahead prediction of indoor temperature to implement model predictive control

Model-based predictive control (MPC) strategies for heating, ventilation, and air-conditioning (HVAC) systems present an opportunity to lower building energy consumption and operational costs. Such approaches rely on the development of a model to precisely forecast building thermal dynamics, such as room air temperature or heating/cooling rate, and make control-related decisions. The control-oriented modeling of building energy systems should be accurate in predicting indoor conditions and present low computational complexity. These features are the key challenge of implementing advanced control methods such as MPC. Extant studies on building modeling for MPC have focused on step-ahead forecasting techniques to forecast building thermal dynamics, while multistep-ahead forecasting is essential. Moreover, machine learning model suitable in case of the domain-based engineering expertise are also not available. To this aim, we perform a comparative analysis of the grey-box model based on a resistance-capacitance (RC) thermal network and a machine learning model composed of an artificial neural network (ANN) for multistep-ahead prediction of building thermal dynamics using current and historical data. Actual experimental data obtained from the Flexible Research Platform (FRP) in Oak Ridge National Laboratory (US) are used for estimation and validation purposes. The average root mean squared error (RMSE) of the grey-box and ANN models are 0.89 °C and 1.02°C, respectively. Finally, the results indicate that the grey-box model outperforms the ANN model in the considered validation periods in terms of accuracy and prediction stability.

42 ENGINEERING↗
DOE OSTI2021

Impact of size and thermal gradient on supercooling of phase change materials for thermal energy storage

Phase change material based thermal energy storage has many current and potential applications in the heating and cooling of buildings, battery and electronics thermal management, thermal textiles, and dry cooling of power plants. However, connecting lab scale thermal data obtained with differential scanning calorimetry (DSC) to the performance of large-scale practical systems has been a major challenge primarily due to the dependence of supercooling on the size and temperature gradient of the system. Here we show how a phase change material’s supercooling behavior can be characterized experimentally using common lab scale thermal analysis techniques. We then develop a statistics based theoretical model that uses the lab-scale data on small samples to quantitatively predict the supercooling performance for a general thermal energy storage application of any size, including also allowing for the possibility of temperature gradients. Finally, we validate the modeling methodology by comparing to experimental results for solid-solid phase change in neopentyl glycol, which shows how the model successfully predicts the changes in supercooling temperature across a large range of cooling rates (2 orders of magnitude) and volumes (3 orders of magnitude). By accounting for thermal gradients, the model avoids ~2x error incurred by lumped approximations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure, Thermal, and Mechanical Properties Relationships in U and UZr Alloys (Final Report)

Uranium-zirconium (U-Zr) alloys are candidate fuel systems for transmutation based reactors that can be used to burn long-lived minor actinides and fission products in fast spectrum reactors. Metallic fuels have also been gaining more recent attention for applications as accident tolerant fuels, as well as for use in small modular reactors. This research focused on a “science-based” approach to capture the connections between U and U-Zr alloys’ three-dimensional (3-D) microstructure, thermal properties, and mechanical properties through closely coordinated experiments and modeling efforts from the unirradiated to the irradiated fuels. Advanced characterization and modeling techniques were used to understand irradiation-induced microstructural evolution and its direct impact on the thermal and mechanical properties of U and U-Zr fuel. Closely coordinated experiments and modeling were performed to provide crucial data that does not currently exist. Overall, this research spanned multiple length and time scales within the models and experiments. The scope of the research encompassed the understanding of the irradiation effects in U and various U-Zr alloys with particular attention paid to three task areas: (1) microstructural evolution, (2) in-situ/ex-situ thermal and mechanical properties, and (3) multiscale modeling connections to microstructure, thermal, and mechanical properties. This research resulted in (1) the 3-D characterization of neutron irradiated U-Zr fuel in multiple phase regions to better understand fission gas swelling and constituent redistribution, (2) development of a microstructural model linking thermal and mechanical properties via in situ Raman and nanoindentation, (3) and mesoscale phase field modeling was coupled with the AEH method in the MOOSE framework was used to calculate the effective thermal conductivities of U-Zr fuels consisting of α-U and δ-UZr 2 heterogeneous microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Model-based quantification of margins and uncertainties in metal additive manufacturing for process design and qualification

Laser powder bed fusion (LPBF) Additive Manufacturing (AM) has the potential to enable the production of components with novel designs and material properties unachievable otherwise. However, process repeatability is a challenge, making qualification ill-defined and greatly reducing the utility of what could be an important manufacturing technology. In this work, a combination of modeling, uncertainty quantification (UQ), and experimentation are used in an effort to predict and bound the range of possible outcomes of the LPBF process. Quantities of interest predicted are melt pool dimensions, microstructure features, and mechanical distortions. A combination of high fidelity thermal-fluid models, microstructure growth models, and reduced fidelity, rapid thermal and mechanical models are used. Uncertainty propagation techniques are used to predict probability distributions of quantities of interest from estimates of process uncertainties. Repeated experiments are done to quantify observed probability distributions and compared to predicted distributions to determine if predictions are precise and accurate. Novel modeling methods are microstrucutre characterization techniques are also discussed. It is found that high fidelity models do a generally good job bounding experimentally observed melt pool morphologies for both bead-on-plate and powder bed cases. Microstructure models are able to bound a number of experimentally observed microstructure statistics, but with low precision due to challenges with calibrating the microstructure growth model parameters. A developed modified inherent strain distortion model does not accurately predict observed distortions. A lumped laser distortion model shows promise in being both accurately and precisely bounding observed outcomes from the deflection comb build, but requires further evaluation on more builds and geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal conductivity modeling of monodispersed microspheres using discrete element method

Particle beds are widely used in various systems and processes, such as particle heat exchangers, granular flow reactors, and additive manufacturing. Accurate modeling of the thermal conductivity of particle beds and understanding of their heat transfer mechanisms are important. However, previous models were based on simple cubic packing of particles, which could not accurately represent the actual heat transfer processes under certain conditions. Here, we examine the effect of the packing structure on the thermal conductivity of particle beds. We use monodispersed silica microspheres with average particle sizes ranging from 23 to 330 μm as a model material. We employ a transient hot-wire technique to measure the thermal conductivity of the particle beds with packing density of 43%–57% within a temperature range of room temperature to 500 °C and under N2 gaseous pressures of 20–760 Torr. We then use a discrete element method (DEM) to obtain the realistic packing structure of the particles, which is then fed into a finite-element model (FEM) to calculate the thermal conductivity, with the consideration of solid conduction, gas conduction, and radiation heat transfer. Our results show that the thermal conductivity model based on the more realistic random packing structure derived from the DEM shows better agreement with the experimental data compared to that based on the simple cubic-packing structure. The combined DEM and FEM methodology can serve as a useful tool to predict the effective thermal conductivity of particle beds and to quantify different heat transfer mechanisms under various conditions.

14 SOLAR ENERGY↗
DOE OSTI2020

Impact of uranium oxide (UO 2 ) fuel with molybdenum (Mo) inserts on pressurized water reactor performance and safety

This work investigates nuclear reactor performance and safety characteristics of UO 2 with high thermal conductivity Mo insert structures by using multiphysics modeling techniques. Additionally, the purpose of this study is to use scoping analyses to quantify the impact of using Mo inserts from neutronic and heat transfer standpoints. Attention is given to reactor performance parameters, such as cycle length, maximum fuel temperature, temperature gradients in the fuel, and stored energy in the fuel. The finite-element code BISON and the Monte Carlo particle transport code Serpent were used to perform sensitivity analyses on the Mo insert geometry to optimize the insert design and inform larger scale modeling that required the homogenization of the UO 2 and Mo. Although BISON is often used as a fuel performance analysis tool, it is used in this context for heat transfer analysis only. Fuel performance optimization is outside the scope of the current study, but would be important for future work focused on this concept. The results showed that the insert had little impact on neutronic performance and that homogenizing the UO 2 and Mo was acceptable for reactor physics calculations. Reactivity temperature coefficients calculated using homogeneous UO 2 -Mo were shown to be relatively similar to UO 2 , but higher Mo content and 235 U enrichment can reduce the worth of soluble boron and control rods. The effect of insert geometry on heat transfer was much greater, and an approximately 15–20% difference in maximum fuel temperature was predicted between the best and worst performing heat transfer geometries. Furthermore, thermal conductivity calibration based on the finite element analysis results was performed to improve the accuracy of temperature predictions in reactor analysis models that homogenized the UO 2 -Mo fuel. Compared with UO 2 in a pressurized water reactor (PWR), the optimized UO 2 -Mo design increased the margin to fuel melt by 13–32% across the fuel cycle, but it requires the 235U enrichment to exceed 5% to match the cycle length of conventional UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Thermal transport in defective and disordered materials

With significant recent advancements in thermal sciences—such as the development of new theoretical and experimental techniques, and the discovery of new transport mechanisms—it is helpful to revisit the fundamentals of vibrational heat conduction to formulate an updated and informed physical understanding. The increasing maturity of simulation and modeling methods sparks the desire to leverage these techniques to rapidly improve and develop technology through digital engineering and multi-scale, electro-thermal models. With that vision in mind, this review attempts to build a holistic understanding of thermal transport by focusing on the often unaddressed relationships between subfields, which can be critical for multi-scale modeling approaches. For example, we outline the relationship between mode-specific (computational) and spectral (analytical) models. We relate thermal boundary resistance models based on perturbation approaches and classic transmissivity based models. We discuss the relationship between lattice dynamics and molecular dynamics approaches along with two-channel transport frameworks that have emerged recently and that connect crystal-like and amorphous-like heat conduction. Throughout, we discuss best practices for modeling experimental data and outline how these models can guide material-level and system-level design.

42 ENGINEERING↗