Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tape casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Freeze Tape Casting of Functionally Graded Porous Ceramics

Freeze tape casting is a means of making preforms of ceramic sheets that, upon subsequent completion of fabrication processing, can have anisotropic and/or functionally graded properties that notably include aligned and graded porosity. Freeze tape casting was developed to enable optimization of the microstructures of porous ceramic components for use as solid oxide electrodes in fuel cells: Through alignment and grading of pores, one can tailor surface areas and diffusion channels for flows of gas and liquid species involved in fuel-cell reactions. Freeze tape casting offers similar benefits for fabrication of optimally porous ceramics for use as catalysts, gas sensors, and filters.

Sofie, Stephen W.↗
DOE OSTI2020

Tape casting and characterizations of MgO ceramics

Herein we report a high density MgO ceramic substrate produced by the tape casting technology. The tape casting formulation and process produced a uniform tape free of cracking. Y 2 O 3 and SiO 2 were used as the sintering aid for the pressureless sintering of the green tape. X-ray diffraction phase identification indicates that MgO is the main phase, while both Y 2 O 3 and SiO 2 sintering aids react with MgO to form MgY 4 Si 3 O 13 as the second phase. Liquid phase sintering occurs in the temperature range from 1030°C to ~1500°C, which is confirmed by the simultaneous Thermal Gravitation Analysis/ Differential Scanning Calorimeter (TGA/DSC) and the percent linear shrinkage and densification. A 96.5% theoretical density was achieved by presureless sintering at 1650°C for 2 hours, which was further increased to a fully dense structure using hotisostatic- pressing(HIP) at 1650°C and 207 MPa in argon. Scanning electron microscopy (SEM) and energy dispersive(EDS) spectroscopic analysis on the HIP’ed sample show that MgY 4 Si 3 O 13 is located at the MgO grain boundary and the sample has a fully dense structure. The refractive indices and extinction coefficient were measured on the HIP’ed sample along with thermal properties and dielectric properties. Thermal diffusivity and heat capacity were measured to calculate the thermal conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Optimization of Lithium Content and Sintering Additives in Tape Cast Lithium Garnet Electrolyte Sheets

The lithium garnet (LLZO) remains one of the most promising electrolyte materials for producing solid state batteries. Tape casting is one method for producing the thin ceramic electrolyte layer required for a high-performance solid state battery. Processing of LLZO is complicated by several factors including lithium volatilization, abnormal grain growth and phase instability. Many of these issues are exacerbated in tape cast sheets by the sheets' higher surface area to volume ratio, when compared to pellet processing methods. Here, we report on an environmentally friendly aqueous tape casting process for LLZO using methylcellulose as a binder and compare final sheet properties to other, solvent-based, options. Solids loading, binder content, dispersant composition, and wetting agent type are varied to improve ease of casting and enhance properties of the as-cast tape. Lithium content in sintered LLZO sheets is controlled by the inclusion of excess Li 2 CO 3 as lithium source in the ceramic tape itself and by a novel method of producing a lithium-saturated furnace atmosphere. Sintering time and temperature are optimized, and rapid thermal processing is investigated as a method of reducing lithium loss. Al 2 O 3 and MgO are examined for use as sintering additives. Characterization of LLZO sheets is performed with XRD, EIS and SEM. Li 2 CO 3 and sintering additive levels are optimized for ionic conductivity and density. The optimization effort improved the conductivity and density of 100µm thick sintered sheets to greater than 3x10 -4 S/cm conductivity and 90% density.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Tape casting and partial melting of Bi-2212 thick films

To produce Bi-2212 thick films with high critical current densities tape casting and partial melting is a promising fabrication method. Bi-2212 powder and organic additives were mixed into a slurry and tape casted onto glass by the doctor blade tape casting process. The films were cut from the green tape and partially molten on Ag foils during heat treatment. We obtained almost single-phase and well-textured films over the whole thickness of 20 microns. The orientation of the (a,b)-plane of the grains was parallel to the substrate with a misalignment of less than 6 deg. At 77 K/0T a critical current density of 15, 000 A/sq cm was reached in films of the dimension 1 cm x 2 cm x 20 microns (1 micron V/cm criterion, resistively measured). At 4 K/0T the highest value was 350,000 A/sq cm (1 nV/cm criterion, magnetically measured).

Buhl, D.↗
DOE OSTI2024

Binder systems and methods for tape casting lithium garnet electrolytes

Slurry compositions, tape casting binder systems and fabrication methods for the fabrication of lithium-garnet electrolyte scaffolds for use in solid state batteries and other devices are provided. Slurry compositions may be optimized mixtures of LLZO powder, a dispersant, a lithium salt, a wetting agent a binder, a plasticizer and at least one solvent. The optimized ceramic slurry compositions may include MgO as a sintering additive to improve density and ionic conductivity of the doped-LLZO sheets and produce a fine-grained microstructure. Sintering protocols for cast slurries of commercially available doped LLZO powders eliminate the requirement of mother-powder coverings or externally applied pressure. An environmentally friendly water-based system using methylcellulose as a binder is also provided producing green tape and final properties comparable to those obtained with organic solvent-based systems.

Jonson, Robert↗
NASA NTRS2001

One-step Tape Casting of Composites via Slurry on Fiber

A process by which metal matrix composites can be made was presented. The process involves putting a powder slurry on fibers to make a precursor green tape. These green tapes are cut, stacked and hot pressed to form the fully dense composite. A computer program was presented which enables complete quantification and control of the process. Once some easily obtained properties of the slurry and its behavior are determined (such as the shrinkage from the wet to green state, and the density of the green tape) modification of the fiber spacing and blade height give the maker precise control of fiber volume fraction, and fiber architecture in the composite. The process was shown to be accurate and flexible through the production of a wide variety of volume fraction fiber composites made from a wide variety of fibers and powders. The most time consuming step of the tape casting process (other than hot pressing) was winding the fiber on the drum. The tape casting techniques developed resulted in high quality metal matrix composites, with ultimate tensile strength in the range of 215 ksi (1477 MPa), a strain at failure of 1.15 percent, and in fatigue at room temperature 0 to 120 ksi, n = 0.3 Hz, a 4-ply Ti-24Al-11Nb/SCS-6, 32 vol% fiber tape cast composite lasted 202,205 cycles with a maximum strain on the 100th cycle of 0.43 percent.

deGroh, Henry C., III↗
DOE OSTI2024

Superior electrochemical performance and reduced heat generation in 3D printed vs. 2D tape-casted NMC622 electrodes

This study compares the charge storage mechanisms, thermodynamics behavior, ion transport, and heat generation in NMC622 electrodes fabricated using a novel 3D printing process and the conventional 2D tape casting process. First, potentiometric entropy measurements revealed that the charge storage mechanisms for both types of electrodes consisted of lithium deintercalation in a homogeneous solid solution of NMC622 followed by a transition from a hexagonal (H1) phase to another hexagonal (H2) phase through a monoclinic (M) phase. Both types of electrodes had similar thermodynamics behavior with overlapping entropic potential profiles. Furthermore, operando isothermal calorimetry at high C-rates indicated that the 3D printed electrodes featured larger specific capacity and better rate performance than the 2D tape-casted electrodes. The better performance of 3D printed electrodes was attributed to their larger electrode/electrolyte interfacial surface area and electrical conductivity as well as their faster lithium ion transport. As a result, the instantaneous heat generation rates were smaller in 3D printed electrodes than in 2D tape-casted electrodes, thus resulting in lower overall specific electrical energy and thermal energy dissipation per unit charge stored. Overall, additive manufacturing techniques offer great potential in producing electrodes with superior electrochemical performance and reduced heat generation for fast charging batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Optimization of Tape Casting for Fabrication of Li 6.25 Al 0.25 La 3 Zr 2 O 12 Sheets

Tape casting is an attractive technology for the scalable manufacturing of thin lithium garnet electrolyte (LLZO) layers for solid state battery applications. Processing of LLZO is complicated by many factors including lithium volatilization, abnormal grain growth, and phase instability, which are exacerbated by high surface area to volume ratios. In this work a sintering protocol for commercially available Li 6.25 Al 0.25 La 3 Zr 2 O 12 Sheets (Al-LLZO) powder was developed that requires no mother-powder covering or externally applied pressure. MgO was investigated as a sintering additive to improve density and ionic conductivity of the Al-LLZO sheets and produce a fine-grained microstructure. Al-LLZO sheets with 5 wt % MgO had densities of > 90% and ionic conductivity > 2 × 10 -4 S/cm. The optimized ceramic composition and sintering protocol were used to compare several tape casting binder systems. A "green"water-based system using methylcellulose as a binder was developed with green and final properties comparable to those obtained with solvent-based systems.

25 ENERGY STORAGE↗
NASA NTRS1985

Tape casting as an approach to an all-ceramic turbine shroud seal

Gas path seals have a one-dimensional variation in material requirement. Tape casting is a method which allows the fabrication of thin ceramic sheets, which may be laminated to accommodate these requirements. Using tape casting, thin sheets of zirconia (0.25 mm) were fabricated. These castings were successfully laminated and fired without bloating or delamination, demonstrating the feasibility of this approach.

Cawley, J. D.↗
DOE OSTI2022

Bilayer hybrid graphite anodes via freeze tape casting for extreme fast charging applications

Extreme fast charging (XFC) of lithium-ion batteries is critical for continuous market adoption of electric vehicles. However, mass transport limitations and sluggish kinetics lead to lithium plating in graphite anodes under fast charging conditions. One approach to address the mass transport limitation in graphite is to design low-tortuosity electrodes to enhance ionic transport. In this study, a bilayer hybrid structured electrode with directionally aligned channels was developed via freeze tape casting, which enables faster lithium ion diffusion through the graphite electrode. A scalable roll-to-roll process was designed in which slurry can be cast on any substrates for simple processing. Additionally, electrochemical impedance spectroscopy measurements indicated that the bilayer hybrid coating had both low tortuosity and short diffusion pathways, enabling XFC charging. Rate testing for the bilayer hybrid electrode indicated superior performance over the other coatings, exhibiting a ~20% improvement in the charge capacity compared with the conventional coating at 5C and 10 min total charging time. The bilayer hybrid electrode also demonstrated a 10% improvement in capacity retention compared with the conventional electrode after 1000 cycles at XFC conditions. This study demonstrates freeze tape casting as a scalable way to fabricate low-tortuosity electrodes for XFC applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries

Most previous studies about halide solid-state electrolytes have used pellets prepared by uniaxial pressing, which is a good approach for materials development but is not suitable for commercialization. Thinner electrolyte layers that can be scaled up to large cell areas are required, and tape casting is a promising approach. It is challenging, however, as halide materials are reactive with most of the conventional solvents used in the process. In this study, solvents with low polarity, such as toluene, are found to be compatible with the Li 3 YBr 6 halide material. A wide variety of candidate binders that are soluble in toluene are studied. MSB1–13 binder is preferred, based on the ionic conductivity and mechanical properties of the tape. Electrolyte tapes (<70 μ m) are successfully cast on Al substrates, using 2 wt% binder. The resulting room temperature ionic conductivity is 2 × 10 −4 S cm −1 . Two composite cathodes including active material (LiFePO 4 or LiNi 0.82 Mn 0.07 Co 0.11 O 2 ) and 1 to 1.5 wt% MSB1–13 are tape cast as proof-of-concept for a scalable cell fabrication approach. A LiFePO 4 cell shows good retention at 25 °C. The performance of NMC cells with tape electrolyte or pellet electrolyte is similar. This study demonstrates the feasibility of tape casting halide-based electrolytes and cathodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Freeze Tape Casting Electrode with Bilayered Architecture for High-Performance Lithium-Ion Batteries

A facile freeze tape casting (FTC) strategy is utilized to prepare bilayered 4 mAh cm –2 high-loading LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathodes. The bottom layer is a conventional nonaqueous electrode, which has a dense structure for high-energy purposes. Further, the top layer is prepared by the proposed FTC, exhibiting a porous feature for high-power requirement. With the assistance of FTC, the bilayered electrodes successfully deliver enhanced rate and cyclic performance due to the improved lithium-ion diffusion kinetics and pathways. Therefore, the proposed FTC strategy and its delivered electrodes are promising for energy- and power-density lithium-ion batteries, potentially enlightening the research and development of lithium-ion battery manufacturing.

25 ENERGY STORAGE↗
DOE OSTI2024

Pioneering Microporous Layers for Proton-Exchange-Membrane Water Electrolyzers via Tape Casting

The imperative shift towards decarbonization necessitates the production of clean hydrogen through water electrolysis, powered by renewable energy sources. Among electrolyzer technologies, proton-exchange-membrane (PEM) systems emerge as a promising option for large-scale hydrogen generation due to their modular design and rapid response, aligning well with the intermittency of renewable energy. In this study, we employ a tape casting method to fabricate microporous layers (MPLs), both as a single layer and as a bilayer over commercial porous transport layers (PTLs), to further enhance performance of water electrolyzers. We demonstrate that microporous layers require adequate pore sizes to facilitate gas removal, preventing gas flooding and preserving electrolyzer performance. Our single layer microporous layers exhibit lower overpotentials compared to commercial sintered Ti PTLs by 142 mV at 4 A·cm ⁻2 . Moreover, we show that having an effective microporous layer enhances electrolyzer performance irrespective of the substrate used, offering avenues for cost reduction. We also investigate novel PTL structures with reduced tortuosity and integrated MPL fabricated via phase inversion tape casting, resulting in a performance enhancement of 92 mV. Our findings unravel the critical role of microporous layer structures and their impact on electrolyzer performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

On the quality of tape-cast thin films of sulfide electrolytes for solid-state batteries

All-solid-state lithium batteries (ASSLBs) have the potential to increase energy density, improve safety, and allow for lower manufacturing costs compared to conventional, liquid-based Li-ion batteries. The thickness of solid electrolyte (SE) layer dictates the cell-level energy density and it is desirable to make the SE layer as thin as possible while maintaining uniformity and defect-free. Manufacturing a high- quality, thin sulfide SE layer at large-scale, however, is challenging. Previous studies have addressed the compatibility of materials used for manufacturing thin sulfide SE films, paving the way for further investigation of processing conditions and film quality. Here we report a strong correlation between the solid loading of dispersions and the quality of tape-casted thin sulfide SE films. We also demonstrate a method for quantifying the quality of thin SE films by observing both pin-hole defects and larger heterogeneous agglomerations of particles in the films. Our thin sulfide SE films containing ~5 wt% binder are defect-free and show similar ionic conductivity compared to a cold-pressed, binder-free, thick SE pellet, resulting in an ~11X reduction of area specific resistance. Here, this work on the solid loading of the dispersion used in a scalable tape casting process provides insight for manufacturing high-quality, thin sulfide SE films and to increase the cell-level energy density of ASSLB.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Scalable Freeze-Tape-Casting Fabrication and Pore Structure Analysis of 3D LLZO Solid-State Electrolytes

Nonflammable solid-state electrolytes can potentially address the reliability and energy density limitations of lithium-ion batteries. Garnet-structured oxides such as Li 7 La 3 Zr 2 O 12 (LLZO) are some of the most promising candidates for solid-state devices. Here, three-dimensional (3D) solid-state LLZO frameworks with low tortuosity pore channels are proposed as scaffolds, into which active materials and other components can be infiltrated to make composite electrodes for solid-state batteries. To make the scaffolds, we employed aqueous freeze tape casting (FTC), a scalable and environmentally friendly method to produce porous LLZO structures. Using synchrotron radiation hard X-ray microcomputed tomography, we confirmed that LLZO films with porosities of up to 75% were successfully fabricated from slurries with a relatively wide concentration range. The acicular pore size and shape at different depths of scaffolds were quantified by fitting the pore shapes with ellipses, determining the long and short axes and their ratios, and investigating the equivalent diameter distribution. The results show that relatively homogeneous pore sizes and shapes were sustained over a long range along the thickness of the scaffold. Additionally, these pores had low tortuosity and the wall thickness distributions were found to be highly homogeneous. These are desirable characteristics for 3D solid electrolytes for composite electrodes, in terms of both the ease of active material infiltration and also minimization of Li diffusion distances in electrodes. The advantages of the FTC scaffolds are demonstrated by the improved conductivity of LLZO scaffolds infiltrated with poly(ethylene oxide)/lithium bis(trifluoromethanesulfonyl)imide (PEO/LITFSI) compared to those of PEO/LiTFSI films alone or composites containing LLZO particles.

36 MATERIALS SCIENCE↗
NASA NTRS1989

High density tape casting system

A system is provided for casting thin sheets (or tapes) of particles bound together, that are used for oxygen membranes and other applications, which enables the particles to be cast at a high packing density in a tape of uniform thickness. A slurry contains the particles, a binder, and a solvent, and is cast against the inside walls of a rotating chamber. Prior to spraying the slurry against the chamber walls, a solvent is applied to a container. The solvent evaporates to saturate the chamber with solvent vapor. Only then is the slurry cast. As a result, the slurry remains fluid long enough to spread evenly over the casting surface formed by the chamber, and for the slurry particles to become densely packed. Only then is the chamber vented to remove solvent, so the slurry can dry. The major novel feature is applying solvent vapor to a rotating chamber before casting slurry against the chamber walls.

Collins, Earl R., Jr.↗
DOE OSTI2023

Titanium porous-transport layers for PEM water electrolysis prepared by tape casting

While the porous-transport layer (PTL) is a key component in PEM electrolyzers, it is one of the most underexplored due to limited available structures. In this work, we present a novel PTL design for PEM water electrolyzers enabled by a cost-effective, scalable tape-casting technique. Here, a precise control of the PTL pore structure is achieved by incorporating poreformers of various sizes, and by varying the titanium and poreformer ratio. The structures are characterized with SEM and synchrotron X-ray computed tomography imaging techniques. Comprehensive electrochemical performance analysis demonstrates that higher titanium loading provides improved contact at the catalyst-layer/PTL interface but suffers from severe mass-transport losses due to gas bubbles. We solve this mass-transport problem by mixing in large poreformer beads that produce a highly porous structure with excellent gas removal properties yet still maintaining mechanical integrity. The PTL fabricated with 60:40 Ti:PMMA ratio and 60 μm PMMA bead size outperformed the standard commercial Ti powder-based PTL by 62 mV at 4 A/cm 2 .

25 ENERGY STORAGE↗
NASA NTRS1987

High-Density-Tape Casting System

Centrifuge packs solids from slurry into uniform, dense layer. New system produces tapes of nearly theoretical packing density. Centrifugal system used to cast thin tapes for capacitors, fuel cells, and filters. Cylindrical rotary casting chamber mounted on high-speed bearings and connected to motor. Liquid for vapor-pressure control and casting slurry introduced from syringes through rotary seal. During drying step, liquid and vapor vented through feed tubes or other openings. Laminated tapes produced by adding more syringes to cast additional layers of different materials.

Collins, Earl R., Jr.↗