Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stagnant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Quasi-stagnant plasmoid in the middle tail - A new preexpansion phase phenomenon

From the analysis of ISEE 3 data it is found that a plasmoid is sometimes formed in the middle tail outside the intervals of the substorm expansion phase. This plasmoid is produced by reconnection at the X-type neutral line, which is located earthward of the distant neutral line but beyond the substorm-associated near-tail neutral line, and it is almost stagnant in that the associated flow speed is less than 300 km/s. The blocking effect of the distant neutral line is the most probable reason for the slow movement. The quasi-stagnant plasmoid is observed at x = -60 to - 100 earth radii for a duration of a few tens of minutes, and in about one half of the cases it is followed by the fast tailward streaming. The onset of this streaming tends to coincide with the onset of the substorm expansion phase, and this probably occurs when the reconnection at the middle-tail neutral line comes close to processing the last closed field line. Intensification of the dawn-to-dusk electric field that causes the mantle plasma to reach the plasma sheet boundary closer to the earth is suggested as the reason for the formation of the middle-tail neutral line earthward of the distant neutral line. The effects on the energetic particle flux and relation to the near-tail reconnection are also discussed.

Nishida, A.↗
DOE OSTI2023

Mass transfer in catalytic depolymerization: External effectiveness factors and serendipitous processivity in stagnant and stirred melts

Several heterogeneous catalysts are being developed to recycle plastics. Most operate in viscous polymer melts, where external mass transfer effects could limit the supply of co-reactants to active sites. External mass transfer can also impede the diffusion of long chain products away from the catalyst after each cut. Product egress limitations could potentially confer unintentional processivity to catalyst operation, i.e. a tendency for the catalyst to repeatedly cut the same chain after an initial encounter. We formulate reaction–diffusion equations to quantify mass transfer effects on the co-reactant transport to the catalyst and the degree of serendipitous processivity. Results are developed for catalysts in stagnant or stirred melts, with simple expressions involving Damkohler, Peclet, and Sherwood numbers, i.e. dimensionless combinations of rate constants, catalyst particle size, polymer diffusivities, and shear rates (where applicable). In conclusion, we estimate the impact of these effects for a spherical core–shell catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1999

Hot Gas Testing Results of Stagnant Volume Filling Through a Back-Filled RSRM Nozzle Joint

Silicone rubber is back-filled into RSW nozzle joints after assembly. A possible artifact of this process is the formation of small pathways through this filter leading to sensitive sealing materials within the joint. At motor ignition, hot gases fill the stagnant volumes within the joint through this path. A series of 14 test has been completed studying this scenario and providing anchoring data for thermal/flow models. Parameters such as gas path cross section, gas path length, gas path materials, fill volume size, and post path gas spreading prior to unpingement on seal material, have been investigated. Tests were accomplished using geometry similar to RSRM nozzle joint 4 with attached volumes replicating the free volume and flow friction in the actual hardware. The test hardware simulated 8 inches of the full-scale circumference. Testing has pointed to changes required in model boundary condition assumptions and gas dynamics corrections for gas paths of this size and geometry. Areas ,where this date has provided improvement in analysis models will be covered as well as model inadequacies that require separate specialized efforts. Questions remaining after this testing and a possible direction for future testing will be suggested.

Prince, Andrew S.↗
DOE OSTI2023

Amorphous Mn2SiO4: A potential manganese phase in the stagnant slab

Abstract Tephroite (Mn2SiO4), together with some manganese (Mn)-rich mineral inclusions, has been found in ophiolite-hosted diamonds, possibly originating from Mn-nodules and sediments that were once deposited on the oceanic floor and later subducted into the deep mantle, which provides evidence for oceanic crustal recycling. However, the state and behavior of tephroite under high-pressure and high-temperature conditions remain poorly understood. In this study, we conducted in situ synchrotron single-crystal X-ray diffraction (XRD) and Raman spectroscopy of synthetic tephroite up to ~30 GPa and ~900 K. The XRD and Raman spectroscopy experiments in this study first show that tephroite undergoes a pressure-induced, irreversible, amorphous transformation above ~20 GPa. Temperature (<900 K) is found to be an insignificant factor governing the process of amorphous transformation. Amorphous tephroite may be a potential phase in a rapidly cooling oceanic lithospheric subduction slab stagnating at the bottom of the mantle transition zone.

Geochemistry & Geophysics↗
NASA NTRS2004

Convection in Icy Satellites: Implications for Habitability and Planetary Protection

Solid-state convection and endogenic resurfacing in the outer ice shells of the icy Galilean satellites (especially Europa) may contribute to the habitability of their internal oceans and to the detectability of any biospheres by spacecraft. If convection occurs in an ice I layer, fluid motions are confined beneath a thick stagnant lid of cold, immobile ice that is too stiff to participate in convection. The thickness of the stagnant lid varies from 30 to 50% of the total thickness of the ice shell, depending on the grain size of ice. Upward convective motions deliver approximately 10(exp 9) to 10(exp 13) kg yr(sup -1) of ice to the base of the stagnant lid, where resurfacing events driven by compositional or tidal effects (such as the formation of domes or ridges on Europa, or formation of grooved terrain on Ganymede) may deliver materials from the stagnant lid onto the surface. Conversely, downward convective motions deliver the same mass of ice from the base of the stagnant lid to the bottom of the satellites ice shells. Materials from the satellites surfaces may be delivered to their oceans by downward convective motions if material from the surface can reach the base of the stagnant lid during resurfacing events. Triggering convection from an initially conductive ice shell requires modest amplitude (a few to tens of kelvins) temperature anomalies to soften the ice to permit convection, which may require tidal heating. Therefore, tidal heating, compositional buoyancy, and solid-state convection in combination may be required to permit mass transport between the surfaces and oceans of icy satellites. Callisto and probably Ganymede have thick stagnant lids with geologically inactive surfaces today, so forward contamination of their surfaces is not a significant issue. Active convection and breaching of the stagnant lid is a possibility on Europa today, so is of relevance to planetary protection policy.

Barr, A. C.↗
DOE OSTI2023

Advancements in conventional and 3D printed feed spacers in membrane modules

Plate & frame and spiral-wound modules are used for gas separation, pervaporation, reverse osmosis, nanofiltration, ultrafiltration, microfiltration, electro-dialysis, electro-deionization, membrane distillation and forward osmosis membrane processes. Feed channel spacers are an integral part of both module types – providing mechanical support for a cross-flow channel through the module and, in most cases, promoting mixing to enhance mass transfer to reduce concentration polarization and fouling. However, enhanced mass transfer comes at a cost of increased hydraulic pressure losses and stagnant zones wherever a spacer filament touches a membrane surface. Further, these stagnant zones exacerbate membrane fouling and make cleaning more difficult. Efforts to improve feed spacer performance largely focus on adjusting the chemistry or geometry of the spacer to mitigate these challenges. Additive manufacturing (i.e. 3D printing) offers new degrees of freedom in feed spacer design and production, which opens up a new area of research in membrane technology. This review critically assesses the peer-reviewed literature on conventional net- or mesh-style feed spacers in addition to various novel spacer geometries and chemistries produced via 3D printing. We further review and evaluate conventional spacer manufacturing methods and discuss advantages and disadvantages of 3D printed spacers.

3D printing↗
DOE OSTI2021

Optical and electrochemical effects of H 2 and O 2 bubbles at upward-facing Si photoelectrodes

The effects of the size, contact-angle, and coverage of gas bubbles on solar fuels devices were characterized at cm-scale, upward-facing planar and microwire-array Si photoelectrodes in stagnant electrolytes. Experimental measurements were supported by ray-tracing simulations of surface attached gas bubble films. A dilute, redox-active tracer allowed for the quantification of the mass-transport effects of bubble coverage during photoanodic O 2 (g) evolution at upward-facing photoanodes in 1.0 M KOH(aq.). Measurements of the gas coverage at upward-facing p-Si photocathodes in 0.50 M H 2 SO 4 (aq.) allowed for the nucleation rate and contact angle of H 2 (g) bubbles to be evaluated for systems having various surface free energies. Under simulated solar illumination, the rapid departure of small O 2 (g) bubbles produced stable photocurrents at upward-facing oxygen-evolving Si photoanodes and yielded increased mass-transport velocities relative to a stagnant electrolyte, indicating that bubbles can provide a net benefit to the photoelectrochemical performance of an upward-facing photoanode in solar fuels devices.

14 SOLAR ENERGY↗
DOE OSTI2023

Field Testing of Self-Healing Metallic Coatings for Internal Corrosion Protection of Natural Gas Pipelines

Internal corrosion occurs in natural gas pipelines primarily due to the presence of water, carbon dioxide, and hydrogen sulfide. Internal corrosion can eventually result in leakage, cracks, and rupture of the pipeline. The objective of this work is to mitigate internal corrosion in steel pipelines transporting natural gas using cold spray coatings. The corrosion behavior of carbon steel coated with self-healing zinc chromium (ZnCr) and zinc niobium (ZnNb) cold spray coatings was investigated in a natural gas environment. For comparison purposes, hot-dip galvanized steel (HDGS) was tested under the same conditions as cold spray coatings. The field test was performed at the NW Natural gas storage facility in Mist, Oregon. The field test was conducted in a 6-inch diameter pipe transporting wet natural gas out of an underground storage well at 500 psi and 4.4 °C. The coupons were tested for 15 and 32 days under stagnant and flow conditions, respectively. Weight loss method was used to measure the corrosion rate of metallic coatings. Post-corrosion surface characterization was performed on the specimen using a scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS). Crystalline phases were determined by X-ray diffraction (XRD). The field-test results confirmed that the metallic coatings provided corrosion protection of carbon steel exposed to wet natural gas under stagnant and flow conditions. The formation of the ZnCO 3 layer on top of ZnNb and ZnCr coatings led to passivation of the coatings which helps to reduce the self-corrosion. These layers form a barrier for diffusion of corrosive species to the surface.

03 NATURAL GAS↗
DOE OSTI2025

MOSCATO Development and Integration in Fiscal Year 2025: Implementation of Multiphase, Multiphysics Modeling Capabilities for Molten Salt Systems

MOSCATO (Molten Salt Chemistry and Transport) is a multiphysics code that provides high-fidelity, coupled simulations of fluid flow, heat transfer, mass transfer, chemistry, electrochemical phenomena, and alloy corrosion for molten salt systems. In FY25, significant developments were made to the code package, enhancing its capabilities for modeling all relevant phenomena within operating moltens salt reactors (MSRs). The developments and activities in FY25 included: 1. Implementation of Level-Set methods to enable modeling of single-bubble behavior in molten salts. In FY25, the Level-Set two-phase flow modeling implementation was improved to simulate single bubble behavior with molten salt media. The large density and viscosity ratios between typical gases and molten salt liquids present challenges for these types of numerical solvers. With enhancements to the pressure projection method, MOSCATO’s Level-Set solver was able to be successfully validated to experiments related to helium bubble rise in stagnant molten salt. The simulated bubble rising velocity showed reasonable good agreement with experimental measurements. The bubble shape and dynamics were also visually compared with experimental snapshots, demonstrating a good qualitative match. 2. Generation of mass transfer correlations for multiphase flow systems. To enable calculations of the tritium transport across the interface between gas bubbles and salt, we modeled high- Schmidt-number mass transfer around a sphere across a broad range of Reynolds numbers. The mesh near the sphere surface was highly refined to resolve steep concentration gradients caused by the low diffusion coefficient. Literature-based mass transfer correlations were compared with the numerical results, and modifications were proposed to improve agreement, particularly at higher Schmidt numbers. These mass transfer correlations were subsequently provided to other national laboratories to help enable high quality mass transfer simulations using lower-order solvers under development within the NEAMS program. 3. Preliminary implementation of a bubbly flow solver. To model bubbly flow in molten salt, we implemented a bubbly flow solver for void fractions less than 5%. To do so, an algebraic relative velocity model that assumes small bubbles with rapid momentum equilibration was added to MOSCATO to compute bubble velocities. Preliminary comparisons with experimental data showed reasonable agreement, and further improvements are underway. 4. Generation of mass transfer correlations for MSRE subchannel The Molten-Salt Reactor Experiment (MSRE) was a landmark historical project that demonstrated the feasibility of molten-salt reactor technology. The MSRE campaign also generated a significant body of experimental data and reports that continue to support molten-salt–related research. In this report, the MSRE core subchannel was used as the reference geometry for a mass transfer study performed with MOSCATO. The geometry and computational mesh were adapted from a previous study, providing adequate resolution for the relatively low Reynolds number in this case. Additional mesh refinement was applied to reach higher Schmidt numbers, enabling the derivation of a reliable mass-transfer correlation for the present scenario. 5. Simulations of oxygen ingressions into molten salt. In the previous fiscal year, we initiated a study to simulate oxygen ingression in stagnant salt. As oxygen enters the salt through its surface, it reacts with Ce 3+ to form solid CeO 2 and other reaction products. To more fully capture the complex diffusion-convection-reaction mechanisms, capabilities for modeling natural convection in the salt vessel were added. These were needed as the flow of the ingressed gas induced flow in the salt caused by surface shear and non-isothermal effects. With these updated physics in place, we were able to successfully reproduce the experimental results for the rate of change of CeCl 3 concentrations versus time. 6. Flow corrosion model validation. In FY24, MOSCATO’s corrosion model was validated against static corrosion experiments. In FY25, this work was extended to a flow corrosion experiment, where FLiNaK salt was driven by natural convection, with initial salt impurities to initiate corrosion. Despite uncertainties in parameters such as elemental diffusion coefficients in the alloy and unknown H + concentrations, the simulations achieved good agreement with experimental results, especially in predicting sample mass losses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1980

Evaluation of a locally homogeneous flow model of spray combustion

A model of spray combustion which employs a second-order turbulence model was developed. The assumption of locally homogeneous flow is made, implying infinitely fast transport rates between the phase. Measurements to test the model were completed for a gaseous n-propane flame and an air atomized n-pentane spray flame, burning in stagnant air at atmospheric pressure. Profiles of mean velocity and temperature, as well as velocity fluctuations and Reynolds stress, were measured in the flames. The predictions for the gas flame were in excellent agreement with the measurements. The predictions for the spray were qualitatively correct, but effects of finite rate interphase transport were evident, resulting in a overstimation of the rate development of the flow. Predictions of spray penetration length at high pressures, including supercritical combustion conditions, were also completed for comparison with earlier measurements. Test conditions involved a pressure atomized n-pentane spray, burning in stagnant air at pressures of 3, 5, and 9 MPa. The comparison between predictions and measurements was fair. This is not a very sensitive test of the model, however, and further high pressure experimental and theoretical results are needed before a satisfactory assessment of the locally homogeneous flow approximation can be made.

Mao, C. P.↗
NASA NTRS1984

Use of the Burton-prim-slichter Equation at High Growth Rates

The following must be assumed in order to derive the classic Burton-Prim-Slichter equation for segregation during crystal growth: isobaric, isothermal, isopotential or uncharged species, binary, planar interface, steady state, constant diffusion coefficient in fluid, no diffusion in crystal, no lateral convection within fluid film at interface with complete mixing beyond (stagnant film model), and either density, total concentration or partial molar volumes constant in the fluid phase. In addition, the effective distribution coefficient and the interfacial distribution coefficient must be defined properly. The velocity in the equation is the growth rate times a factor correcting for the difference in volumetric properties between crystal and fluid. The stagnant film thickness is found to be a function of freezing rate, with the precise functionality depending on the type of stirring occurring in the growth fluid.

Wilcox, W. R.↗
NASA NTRS1986

A study of selected parameters in solid propellant processing

A propellant processing study to identify and control unplanned variation in composite solid propellant properties has shown that burning rate increases with process mixing but is not sensitve to process temperature. Different vertical propellant mixes of the same type were shown to provide different conditions of mixing at the pot wall because of differences in gearing, sometimes resulting in a stagnant wall film. Poor propellant produced in the stagnant wall film was attributed to poor mixing because of viscosity effects and wall film geometry. A control strategy based on briefly heating the wall was demonstrated. The study showed the need for improved process controls, good process instruments, and good propellant testing.

Mckay, R. A.↗
NASA NTRS1990

Creeping flow of a conducting fluid past axisymmetric bodies in the presence of an aligned magnetic field

The use of strong magnetic fields for the control of particle settling in metallic systems is investigated by altering the fluid mechanics in the melt. The fluid mechanism of particle settling is analyzed for the motion around single, axisymmetric particles in the limit of creeping flow for a fluid with a large electrical conductivity. The drag is found to increase proportionately to the intensity of the magnetic field or the Hartmann number Ha. The flowfield forms boundary layers, which thin out with increasing Ha, along the surfaces parallel to the flow. For axisymmetric bodies, the boundary layer separates as the poles of the surface are approached and encloses regions of almost stagnant fluid. These regions spread upstream and downstream along the body with increasing Ha, thereby trapping the particle in a column of stagnant fluid.

Kyrlidis, A.↗
NASA NTRS1991

Magnetopause and cusp observations at Neptune

Plasma and magnetic field measurements in a subsolar cusp region of Neptune are compared with two current models of cusp regions, stemming from earth measurements: (1) a cusp region filled with stagnant plasma separated from the magnetosheath by a tangential discontinuity and (2) a mantle layer of dynamic plasma separated from the sheath by a rotational discontinuity. The plasma observations are more consistent with the mantle-layer interpretation. However, because of the particular trajectory of the Voyager 2 flyby, it was not possible to distinguish the mantle and the stagnant cusp models on geometrical grounds.

Szabo, Adam↗