Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “specific surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Specific surface area as a maturity index of lunar fines

Mature surface fines have an equilibrium specific surface area of about 0.6 sq m/g the equivalent mean particle size being about 3 microns. The adsorption behavior of inert gases (reversible isotherms) indicates that the particles are also nonporous in the size range of pores from 10 to 3000 A. Apparently, in mature soils there is a balance in the forces which cause fining, attrition, pore filling, and growth of lunar dust grains. Immature, lightly irradiated soils usually have coarser grains which reduce in size as aging proceeds. The specific surface area, determined by nitrogen or krypton sorption at 77 K, is a valuable index of soil maturity.

Gammage, R. B.↗
DOE OSTI2024

Enzymatic depolymerization of polyester: Foaming as a pretreatment to increase specific surface area

Abstract Poly(ethylene terephthalate) (PET) is widely used for its high strength‐to‐weight ratio, gas barrier properties, and chemical resistance. The growing PET use highlights the demand for a better recycling system. Enzymatic recycling, alongside mechanical and chemical methods, is eco‐friendly and yields properties similar to virgin PET. Substrate properties ( T g , crystallinity, and specific surface area [SSA]) and enzyme stability significantly impact conversion efficiency. Higher SSA and lower crystallinity tend to yield improved depolymerization when employing leaf compost‐cutinase (LCC‐ICCG) enzymes. This study explored melt extrusion and foaming as pretreatment techniques to modify PET structural properties, using a low‐cost chemical foaming agent (CFA). The monomer conversion rate and efficiency during depolymerization were measured and related to the processing, extrudate micro‐ and meso‐structure, and polyester type. Pretreated PET substrates showed reduced T g , crystallinity, density, and enhanced SSA, resulting in a 90% mass loss for foamed RPET and VPET substrates within 2 days. In contrast, PET with ~30% of cyclohexanedimethanol comonomer exhibited a nearly 50% lower depolymerization rate, with zero BHET production. It indicates that the combination of low crystallinity, low T g , and high SSA leads to improved monomer conversion. These findings emphasize the significance of amorphization and foaming in enhancing PET enzymatic depolymerization.

42 ENGINEERING↗
DOE OSTI2021

Impact of Precipitation Parameters on the Specific Surface Area of PuO 2

Controlling the properties of PuO 2 through processing is of vital importance to environmental transport and fate, production of nuclear fuels, nuclear forensic analyses, stockpile stewardship, and storage of nuclear wastes applications. A number of processing conditions have been identified to control final product properties, including specific surface area (SSA), residual carbon content, adsorption of volatile species, morphology, and particle size. In this paper, a novel approach is developed for the prediction of PuO 2 SSA via the synthetic route of Pu(IV) oxalate precipitation followed by calcination. The proposed model utilizes multivariate regression methodology and leave one out formalism to link Savannah River Site (SRS) precipitation and calcination production data to the SSA of the final product. A comparison among the models provides insight into the accuracy and ability to identify variations amongst the processing data. Additionally, the models may also be used to fit new data outside of the parameters explored in a production facility. Finally, the trained model was compared to a similarly trained conventional model form to illustrate the influence of precipitation parameters on the prediction of the final SSA. The models presented here attempt to provide new methods for more accurate prediction of the PuO 2 product properties in a production scale environment for key environmental and nuclear applications.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Non-destructive evaluation of specific surface area of porous powder systems using experimental and virtual air permeametry

The correlation of flow-permeable surface area (FSSA) of porous initiator powder to its performance is well-established. More specifically, with age, such powders tend to coarsen (i.e., lose surface area), with an accompanying deterioration in performance. Commercially available permeametry apparatuses, such as that from Fisher Scientific or a more modern version from Micromeritics suffers from a few drawbacks, including: (1) the need to work with a fixed mass equivalent of 1 cm 3 of solid material; (2) the need to re-compact the material to monitor aging effects (which can introduce unwanted errors in the derived results); (3) a superfluous design that involves a reference plug, and for the older Fisher Scientific model, the need to eyeball water meniscus height that can lead to inaccuracies; (4) calibrated and tested only for samples packed in cylindrical geometries.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Absorption of the Martian regolith: Specific surface area and missing CO(sub 2)

For most estimates of available regolith and initial degassed CO(sub 2) inventories, it appears that any initial inventory must have been lost to space or incorporated into carbonates. Most estimates of the total available degassed CO(sub 2) inventory are only marginally sufficient to allow for a major early greenhouse effect. It is suggested that the requirements for greenhouse warming to produce old dessicated terrain would be greatly lessened if groundwater brines rather than rainfall were involved and if a higher internal gradient were involved to raise the water (brine) table, leading to more frequent sapping.

Zent, A. P.↗
DOE OSTI2023

WHONDRS River Corridor Sediment and Water Geochemistry and In Situ Sensor Data from Machine-Learning-Informed Sites across the Contiguous United States (v6)

This dataset supports a broader study examining hyporheic zone respiration rates to improve predictive models at a contiguous United States (CONUS) scale. The CONUS-Scale Model-Sample Study (CM) was designed following ICON (integrated, coordinated, open, and networked) principles to facilitate a model-experiment (ModEx) iteration approach, leveraging crowdsourced sampling across the CONUS. New machine learning models were created every month to guide sampling locations. Data from the resulting samples were used to test and rebuild the machine learning models for the next round of sampling guidance. Sampling began in April 2022 and ended in October 2023. In addition to the widely distributed CONUS sites, a more spatially focused sampling occurred in the Yakima River Basin, WA in summer 2022. Data from this more spatially intensive sampling occurred under the label “Second Spatial Study (SSS)” and were also included in the machine learning models. Other data types collected from SSS that were not part of CM were published in a separate data package (https://data.ess-dive.lbl.gov/view/doi:10.15485/1969566). This data package was originally published in February 2023. It was updated in June 2023 (v2; new and modified files); December 2023 (v3; new and modified files); June 2024 (v4; new and modified files); April 2024 (v5; new and modified files); and September 2025 (v6; modified files). See the change history section in the readme for more details. For details on how to navigate data packages generated by this project, see https://data.ess-dive.lbl.gov/portals/PNNLRiverCorridorSFA/About. This dataset is comprised of two folders of field photos and videos, one folder of raw Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) data and one main data folder containing (1) file-level metadata; (2) data dictionary; (3) field metadata; (4) readme; (5) international generic sample number (IGSN) mapping file; (6) field protocols; (7) a subfolder with sample data; and (8) a subfolder with sensor data. The sample data subfolder contains (1) surface water and sediment dissolved organic carbon (DOC, measured as non-purgeable organic carbon, NPOC) data and averages; (2) surface water and sediment total nitrogen data and averages; (3) surface water major cations and anions and averages; (4) sediment grain size data; (5) sediment iron (II) data and averages; (6) wet sediment mass, dry sediment mass, water mass, and wet sediment volume in incubation and sediment ICR vials; (7) sediment incubation respiration rate data and averages; (8) normalized respiration rate data and averages; (9) methods codes; (10) sediment specific surface area; (11) sediment percent carbon and nitrogen; (12) sediment gravimetric moisture and averages; (15) sediment X-ray diffraction (XRD) data; (16) sediment adenosine triphosphate (ATP) and averages; (17) a subfolder with sediment incubation respiration data, scripts, and plots; (18) surface water and sediment FTICR methods; and (19) a subfolder of 9.4 Tesla (9.4T) FTICR-MS data. This folder contains five subfolders, one containing the sediment .xml data files, one containing the water .xml files, one containing the sediment CoreMS output files, one containing the water CoreMS output files, and the other containing instructions and scripts for processing the files in CoreMS (https://github.com/EMSL-Computing/CoreMS).The sensor data subfolder contains (1) a subfolder with miniDOT dissolved oxygen and temperature data and plots; (2) miniDOT dissolved oxygen and temperature summary data; and (3) miniDOT installation methods. All files are .csv, .pdf, .R, .xml, .d, .html, .Rmd, .py, .cal, .json, .jpg, .jpeg, .png, .mov, or .mp4. CORRECTION: Carbon and nitrogen content are reported as percentages. The current column headers "01395_C_percent_per_mg" and "01397_N_percent_per_mg" are incorrect. These should read "01395_C_percent" and "01397_N_percent" and will be corrected in the next version of this data package. We thank the United States Forest Service, Washington Department of Fish and Wildlife, Washington Department of Natural Resources, Cowiche Canyon Conservatory, Washington State Parks and Recreation Commission (Scientific Research Permit #210901), and the Confederated Tribes and Bands of the Yakama Nation for access to field locations where the samples labeled “SSS” were collected. We also thank the Yakama Nation Tribal Council and Yakama Nation Fisheries for working with us to facilitate sample collection and optimization of data usage according to their values and worldview. WHONDRS consortium members were asked to provide any acknowledgments for the collection of samples labeled “CM” and the following is a list of acknowledgments that were submitted with their corresponding Site IDs: (MART) Research activities were conducted in part on the Wind River Experimental Forest within the Gifford Pinchot National Forest; (MP- 100379) Philadelphia is part of Lenapehoking, the ancestral homelands of the Lenape peoples; (MP-102398) Land surveyed is the ancestral homelands of the Nookhose'iinenno (Arapaho), Tsis tsis'tas (Cheyenne), and Nuuchu (Ute); (MP-100749 and MP- 100747) Georgia Coastal Ecosystem LTER, OCE-1832178; (SP-70 and SP-72) Eastern Shoshone, Shoshone-Bannock; (MP- 102944) Funded by Oregon Watershed Enhancement Board. On the traditional lands of the Confederated Tribes of the Siletz, Confederated Tribes of the Grand Rhonde, and the Clatsop-Nehalem Confederated Tribe; (MP- 100607) Holiday Creek is located on the traditional territory of the Monacan Indian Nation; (SP-45) Lafayette Blue Springs State Park; (MP-102420) NSF DEB-2016749; (MP-100019) New Hampshire Agriculture Experiment Station; (SP-35) Rayonier (land owner; https://www.rayonier.com/); (MP- 101276) US Department of Energy, Office of Science, Biological and Environmental Research, Subsurface Biogeochemical Research, Watershed Dynamics and Evolution SFA at ORNL; (MP- 103224) Watershed Dynamics and Evolution SFA at ORNL; (MP- 101584) Traditional lands of the Oceti Sakowin (Dakota, Lakota, Nakoda) and Anishinaabe Peoples.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2005

Sol-Gel Process for Making Pt-Ru Fuel-Cell Catalysts

A sol-gel process has been developed as a superior alternative to a prior process for making platinum-ruthenium alloy catalysts for electro-oxidation of methanol in fuel cells. The starting materials in the prior process are chloride salts of platinum and ruthenium. The process involves multiple steps, is time-consuming, and yields a Pt-Ru product that has relatively low specific surface area and contains some chloride residue. Low specific surface area translates to incomplete utilization of the catalytic activity that might otherwise be available, while chloride residue further reduces catalytic activity ("poisons" the catalyst). In contrast, the sol-gel process involves fewer steps and less time, does not leave chloride residue, and yields a product of greater specific area and, hence, greater catalytic activity. In this sol-gel process (see figure), the starting materials are platinum(II) acetylacetonate [Pt(C5H7O2)2, also denoted Pt-acac] and ruthenium(III) acetylacetonate [Ru(C5H7O2)3, also denoted Ru-acac]. First, Pt-acac and Ru-acac are dissolved in acetone at the desired concentrations (typically, 0.00338 moles of each salt per 100 mL of acetone) at a temperature of 50 C. A solution of 25 percent tetramethylammonium hydroxide [(CH3)4NOH, also denoted TMAH] in methanol is added to the Pt-acac/Ruacac/ acetone solution to act as a high-molecular-weight hydrolyzing agent. The addition of the TMAH counteracts the undesired tendency of Pt-acac and Ru-acac to precipitate as separate phases during the subsequent evaporation of the solvent, thereby helping to yield a desired homogeneous amorphous gel. The solution is stirred for 10 minutes, then the solvent is evaporated until the solution becomes viscous, eventually transforming into a gel. The viscous gel is dried in air at a temperature of 170 C for about 10 hours. The dried gel is crushed to make a powder that is the immediate precursor of the final catalytic product. The precursor powder is converted to the final product in a controlled-atmosphere heat treatment. Desirably, the final product is a phase-pure (Pt phase only) Pt-Ru powder with a high specific surface area. The conditions of the controlled- atmosphere heat are critical for obtaining the aforementioned desired properties. A typical heat treatment that yields best results for a catalytic alloy of equimolar amounts of Pt and Ru consists of at least two cycles of heating to a temperature of 300 C and holding at 300 C for several hours, all carried out in an atmosphere of 1 percent O2 and 99 percent N2. The resulting powder consists of crystallites with typical linear dimensions of <10 nm. Tests have shown that the powder is highly effective in catalyzing the electro-oxidation of methanol.

Narayanan, Sekharipuram↗
NASA NTRS2012

Three-Dimensional Porous Particles Composed of Curved, Two-Dimensional, Nano-Sized Layers for Li-Ion Batteries

Thin Si films coated on porous 3D particles composed of curved 2D graphene sheets have been synthesized utilizing techniques that allow for tunable properties. Since graphene exhibits specific surface area up to 100 times higher than carbon black or graphite, the deposition of the same mass of Si on graphene is much faster in comparison -- a factor which is important for practical applications. In addition, the distance between graphene layers is tunable and variation in the thickness of the deposited Si film is feasible. Both of these characteristics allow for optimization of the energy and power characteristics. Thicker films will allow higher capacity, but slower rate capabilities. Thinner films will allow more rapid charging, or higher power performance. In this innovation, uniform deposition of Si and C layers on high-surface area graphene produced granules with specific surface area (SSA) of 5 sq. m/g.

Yushin, Gleb↗
DOE OSTI2022

The effects of sequential hydrothermal-mechanical refining pretreatment on cellulose structure changes and sugar recoveries

The recalcitrance of lignocellulosic biomass necessitates an efficient pretreatment protocol for operating a successful cellulosic biorefinery. It is critical to improve cellulose accessibility for hydrolysis and fermentation by altering the plant cell wall’s physical structure and chemical composition. Sequential hydrothermal-mechanical refining pretreatment (HMR) allows efficient recovery of cellulosic sugars without utilizing any hazardous chemicals. HMR has been successfully applied to Liberty switchgrass, a bioenergy cultivar released by the USDA, and now it is being applied to oilcane, a recently developed transgenic sugarcane variety engineered to accumulate lipids in its vegetative tissues. Sugar yields of oilcane bagasse (OCB) and switchgrass (SG) treated with HMR are 96.4% and 75.4%, respectively. This study sought to correlate cellulosic sugar yields with structural changes within the cell wall caused by HMR on two distinct bioenergy crops. Simon’s staining technique for the specific surface area analysis showed that HMR increased the specific surface area of pretreated biomass residues by 80–112%. In addition, ATR-FTIR was performed to determine the effects of HMR on physical structures based on the total crystallinity index (TCI) and hydrogen bonding intensity (HBI). Irrespective of biomass type, HMR decreased the initial crystalline cellulose contents of untreated biomass residues by 3.5% and reduced TCI and HBI by 7–13%. Here, the study found that sugar yields were negatively correlated to reducing values of hydrogen bonding intensity, crystalline cellulose content, and total crystallinity index.

09 BIOMASS FUELS↗
DOE OSTI2022

Data for The Effects of Sequential Hydrothermal-Mechanical Refining Pretreatment on Cellulose Structure Changes and Sugar Recoveries

The recalcitrance of lignocellulosic biomass necessitates an efficient pretreatment protocol for operating a successful cellulosic biorefinery. It is critical to improve cellulose accessibility for hydrolysis and fermentation by altering the plant cell wall’s physical structure and chemical composition. Sequential hydrothermal-mechanical refining pretreatment (HMR) allows efficient recovery of cellulosic sugars without utilizing any hazardous chemicals. HMR has been successfully applied to Liberty switchgrass, a bioenergy cultivar released by the USDA, and now it is being applied to oilcane, a recently developed transgenic sugarcane variety engineered to accumulate lipids in its vegetative tissues. Sugar yields of oilcane bagasse (OCB) and switchgrass (SG) treated with HMR are 96.4% and 75.4%, respectively. This study sought to correlate cellulosic sugar yields with structural changes within the cell wall caused by HMR on two distinct bioenergy crops. Simon’s staining technique for the specific surface area analysis showed that HMR increased the specific surface area of pretreated biomass residues by 80-112%. In addition, ATR-FTIR was performed to determine the effects of HMR on physical structures based on the total crystallinity index (TCI) and hydrogen bonding intensity (HBI). Irrespective of biomass type, HMR decreased the initial crystalline cellulose contents of untreated biomass residues by 3.5% and reduced TCI and HBI by 7-13%. The study found that sugar yields were negatively correlated to reducing values of hydrogen bonding intensity, crystalline cellulose content, and total crystallinity index.

Biomass Analytics↗
DOE OSTI2026

Consolidation and Permeability of the B1 and D1 Gas Hydrate Bearing Sands and Associated Seal Sediments of the Extended-Duration Gas Production Test Site on the Alaska North Slope

Gas hydrate, a solid combination of gas (mostly methane in nature) and water molecules stable at low temperatures and elevated pressures, occurs naturally in marine and permafrost-associated environments. Gas hydrate reservoirs, such as those in the Alaska North Slope, have been considered potential energy resources for gas production. To understand the petrophysical and geo-mechanical characteristics of the reservoir, core samples retrieved from the site of the JOGMEC-DOE-USGS collaborative gas hydrate R&D project have been analyzed in the laboratory for their hydraulic and mechanical properties. This paper focuses on both seal and reservoir samples associated with the B1 and D1 sands, which are evaluated for index properties (including porosity, grain size distribution, liquid and plastic limits, specific surface area, and specific gravity), consolidation, permeability, and water retention. Furthermore, the reservoir core samples were tested with pore-filling, laboratory-grown tetrahydrofuran hydrate, in order to assess reservoir behavior during gas production from hydrates. Under simulated in situ stress conditions, the seal and hydrate-free reservoir cores had a permeability anisotropy ratio of k h /k v = 3.0−5.0, and k h /k v = 2.4−3.0 for the reservoir tetrahydrofuran hydrate-bearing cores. The data suggest that depressurizing the reservoir to induce hydrate dissociation alters the reservoir effective permeability in three ways: permeabilities decrease due to porosity lost (e.g., the initial reservoir thickness can decrease by up to 5% upon 7 MPa depressurization), permeability increases due to the loss of solid hydrate in the pore space, and permeability anisotropy k h /k v decreases in response to the evolving pore-space geometry. We show that given the simulated in situ gas hydrate saturations (i.e., S h = 32% in core 7P-2E and S h = 21% in core 20P-4), gas production from the dissociation of tetrahydrofuran hydrate in the two tested cores results in a net increase in effective permeability and a decrease in k h /k v . This study highlights the importance of investigating seal and reservoir sediments and the impacts of depressurization on the porosity and permeability responses during production.

Geological materials↗
DOE OSTI2024

Hierarchically porous electrospun carbon nanofiber for high-rate capacitive deionization electrodes

Capacitive deionization (CDI) is a promising technology that has gained interest for the desalination of brackish water. Hierarchically porous carbons are commonly used as electrodes for CDI due to their high surface areas and controlled pore size distributions that maximize ion adsorption capacity and rate. Electrospinning is an effective way of generating carbon nanofibers with high inter-fiber macroporosity that can be further modified to improve surface area, total pore volume, and pore size distribution. This work describes the use of sacrificial mesopore formers in tandem with a micropore etching technique to induce hierarchical porosity in electrospun fibers. Mesopores are formed via the dissolution of silica nanoparticles that are introduced into the fibers during the electrospinning step. After mesopore formation, micropores are etched into the resulting surface through KOH impregnation and thermal activation. This sequential technique creates a hierarchical network of pores from the inherent macroporosity of the fiber network, to the mesopores, and finally micropores to simultaneously maximize surface area and accessibility. Micropore formation is optimized to maximize specific surface area while maintaining physical integrity of the fibers. Further, the combination of mesopores and micropores enables fast ion adsorption rates and capacity. Carbon fiber electrodes fabricated in this method achieve specific surface areas exceeding 1400 m 2 g -1 , with pore volumes exceeding 1.0cc g -1 . The pore size distributions are highly controlled, with 80% of total pore volume coming from pores <20nm in radius. In 500 ppm constant voltage CDI tests, these fiber electrodes obtain a salt adsorption capacity of over 14 mg g -1 at a salt adsorption rate of ~4mg g -1 min -1 , showcasing the high capacity matched with high rate of these easily fabricated, inexpensive materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure Scale Lithium-Ion Battery Modeling: Part III. When and Where Lithium Plating Occurs and its Correlation with the Electrode Microstructure

Li-ion battery performance and degradation are closely related to the cell’s underlying electrode microstructure. Electrode microstructures are typically characterized with volume-averaged properties that neglect the impact of local heterogeneities. However, local heterogeneities create hot spots that can trigger degradation onset. Herein, a microstructure scale electrochemical model is used to investigate the impact of microstructure heterogeneity on lithium plating. The model predicts lithium plating is not uniform, even when considering a relatively small portion of the electrode (a cross-sectional area of 154×144 µm 2 ), preferring to plate on larger particles as compared to smaller particles. While local heterogeneities control where plating occurs, the model predicts that volume-averaged properties control when plating occurs. Additionally, the model predicts that the active material specific surface area has a linear relationship with the plating onset. However, the linear relationship between increased active material surface area and delayed plating response appears to be sensitive to the microstructure feature used to increase the active interface area. Here, a comparative case-study is explored where the specific surface area is increased by either reducing the active material particle diameter, adding open-porosity cracks, or increasing the active material surface roughness. The model predicts that increasing the specific surface area by reducing the active material particle diameter is the most effective strategy for delaying lithium plating. At 6C, reducing particle size is shown to be 3 and 20 times more effective than, respectively, adding open-porosity cracks and increasing surface roughness. A dual-layer electrode architecture combining gradations both for average properties and uniformities is eventually proposed to improve homogeneous material utilization and reduce degradation at high charge rates.

25 ENERGY STORAGE↗
DOE OSTI2020

The Role of Pentaerythritol Tetranitrate (PETN) Aging in Determining Detonator Firing Characteristics

Pentaerythritol tetranitrate (PETN) is one of the most commonly used explosives for both military and mining applications. PETN is used in EBW (exploding bridge wire) and EFI (exploding foil initiator) detonator devices. Due the widespread usage of PETN, studies focusing on how the explosive changes with age, primarily its function in detonators has received particular interest. Aging studies have identified several factors that affect PETN detonator function over time, most notably the specific surface area of the explosive powder. Though small-scale studies have been performed on specific detonator systems with isolated batches of material, what is missing is a large statistically-significant study focusing on PETN aging characteristics - such as powder coarsening - and their influence on detonator performance. Herein we report the first large statistically viable PETN aging study focusing on four batches of PETN powder from the same stock of PETN using two stabilizers, polysaccharide and TriPEON. PETN was aged both as a free-flowing powder as well as in modified EBW RP-2 detonators, for one month at 75 °C. The PETN powder has been analyzed chemically using Fisher specific surface area analysis, SEM imaging and light scattering particle size analysis. Additionally the detonators were tested for performance through voltage-sweep threshold testing and function time measurements. Findings from the study indicate that aging at 75 °C for one month significantly changes the specific surface area and particle size of unstabilized PETN, leading to increases in detonator function time, but not detonator threshold values. Powders stabilized with TriPEON displayed less significant increases in function time, while powder stabilized with polysaccharide exhibited no aging effects, despite the high temperature aging.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS2012

Objective Characterization of Snow Microstructure for Microwave Emission Modeling

Passive microwave (PM) measurements are sensitive to the presence and quantity of snow, a fact that has long been used to monitor snowcover from space. In order to estimate total snow water equivalent (SWE) within PM footprints (on the order of approx 100 sq km), it is prerequisite to understand snow microwave emission at the point scale and how microwave radiation integrates spatially; the former is the topic of this paper. Snow microstructure is one of the fundamental controls on the propagation of microwave radiation through snow. Our goal in this study is to evaluate the prospects for driving the Microwave Emission Model of Layered Snowpacks with objective measurements of snow specific surface area to reproduce measured brightness temperatures when forced with objective measurements of snow specific surface area (S). This eliminates the need to treat the grain size as a free-fit parameter.

Durand, Michael↗
NASA NTRS2023

Thermal Stability of M x O y Doped Zirconia Aerogels (M = Y, Yb, Gd, Ce, Ca) Studied Through 1200°C

The high porosities and low densities of ceramic aerogels offer outstanding insulative performance in applications where weight is a critical factor. The high surface area-to-volume ratios and specific surface areas provide extremely low thermal conductivity, but also contribute to rapid densification of the pore structure at elevated temperatures. This densification diminishes their favorable properties and inhibits use of aerogels in high temperature applications. This work contributes to a design framework for thermally stable aerogels via the study of dopant chemistry (Y, Yb, Gd, Ca, Ce) in zirconia aerogels. The structural evolution was studied to 1200°C using nitrogen physisorption, scanning electron microscopy, and x-ray diffraction. The role of dopant identity and concentration in thermal stability was elucidated. In context of the design framework, dopant chemistry is an aggregate for many closely related material properties, each of which may contribute to aerogel structural evolution. To develop a truly predictive design framework for ceramic-based aerogels, systematic and comprehensive evaluation of thermodynamic and kinetic properties must be performed in conjunction with studies on structural evolution.

aerogel↗
DOE OSTI2022

Fabrication of High Surface Area Microporous ZnO from ZnO/Carbon Sacrificial Composite Monolith Template

Fabrication of porous materials from the standard sacrificial template method allows metal oxide nanostructures to be produced and have several applications in energy, filtration and constructing sensing devices. However, the low surface area of these nanostructures is a significant drawback for most applications. Here, we report the synthesis of ZnO/carbon composite monoliths in which carbon is used as a sacrificial template to produce zinc oxide (ZnO) porous nanostructures with a high specific surface area. The synthesized porous oxides of ZnO with a specific surface area of 78 m2/g are at least one order of magnitude higher than that of the ZnO nanotubes reported in the literature. The crucial point to achieving this remarkable result was the usage of a novel ZnO/carbon template where the carbon template was removed by simple heating in the air. As a high surface area porous nanostructured ZnO, these synthesized materials can be useful in various applications including catalysis, photocatalysis, separation, sensing, solar energy harvest and Zn-ion battery and as supercapacitors for energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Interaction of gases with lunar materials

The surface chemistry of Apollo 17 lunar fines samples 74220 (the orange soil) and 74241 (the gray control soil) has been studied by measuring the adsorption of nitrogen, argon, and oxygen (all at 77 K) and also water vapor (at 20 or 22 C). In agreement with results for samples from other missions, both samples had low initial specific surface areas, consisted of nonporous particles, and were attacked by water vapor at high relative pressure to give an increased specific surface area and create a pore system which gave rise to a capillary condensation hysteresis loop in the adsorption isotherms. In contrast to previous samples, both of the Apollo 17 soils were partially hydrophobic in their initial interaction with water vapor (both samples were completely hydrophilic after the reaction with water). The results are consistent with formation at high temperatures without subsequent exposure to significant amounts of water.

Holmes, H. F.↗