Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sideslip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Experimental Investigation of Effects of Moderate Sideslip on the Flow Fields near a 45 Degree Swept-wing-fuselage Combination at Low Speed

The flow fields near a 45 degree swept-wing-fuselage combination at moderate angles of sideslip (plus-or-minus 8 degrees), as determined experimentally at low speed, are presented as variations with chordwise distance for various spanwise and vertical locations and angles of attack. The results indicated that for positions close to the fuselage (on and near the plane of symmetry) changes in the angle of sideslip caused large changes in the flow-field characteristics and particularly in the local angles of sideslip, which in some cases were nearly double the static angle of sideslip. In general, the effects of changing the angle of sideslip on the flow-field characteristics for all of the outboard underwing locations were qualitatively similar, although conditions at the more inboard and outboard locations were somewhat more severe for lifting conditions than at the one-half semispan location. The chordwise gradients in the flow parameters for the underwing locations were more severe than for the fuselage locations although the effect of changing the angle of sideslip was less severe, in that the incremental changes in the local angles of sideslip were approximately equal to the static angle of sideslip. Flow conditions near the wing tip were found to be critically dependent on vertical location, with the largest sideslip-induced variations occurring at the nearest vertical locations. The results also indicated that for the outboard underwing locations the wing was the predominant factor in disturbing the field of flow for the conditions investigated.

Alford, William J , Jr↗
NASA NTRS1958

Aerodynamic Characteristics in Sideslip of a Large-Scale 49 deg Sweptback Wing-Body-Tail Configuration with Blowing Applied Over the Flaps and Wing Leading Edge

An investigation has been conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics in sideslip of a large-scale 490 sweptback wing-body-tail configuration having wing leading- edge and flap-blowing boundary-layer control. The wing and tails had an aspect ratio of 3.5, a taper ratio of 0.3, and NACA 65AO06 airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack of about -5 deg to 28 deg for sideslip angles of 0 deg, -5.06 deg, -10.15 deg, and -15.18 deg. Lateral and longitudinal stability and control characteristics were obtained for6a minimized blowing rate. The Reynolds number of the tests was 5.2 x 10(exp 6), corresponding to a Mach number of 0.08. The results of the investigation showed that sideslip to angles of about -15 deg did not require, from a consideration of the longitudinal characteristics, blowing rates over the wing leading edge or flap greater than that established as minimum at zero sideslip. The optimum configuration was laterally and directionally stable through the complete lift-coefficient range including the stall; however, maximum lift for sideslip angles greater than about 50 was seriously limited by a deficiency of lateral control. Blowing over the leading edge of the retreating wing in sideslip at a rate greater than that established as minimum at zero sideslip was ineffective in improving the lateral control characteristics. The optimum configuration at zero sideslip had no hysteresis of the aerodynamic parameters upon recovery from stall.

McLemore, H. Clyde↗
NASA NTRS1981

Influence of sideslip on the kinematics of the helicopter in steady coordinated turns

A steep coordinated helical turn at extreme angles of attack with inherent sideslip is of primary interest in this study. Unlike fixed-wing aircraft, the helicopter in a steady coordinated turn will inherently sideslip. A set of exact kinematic equations describing this motion in steady helical turns has been developed, and a rational definition for the load factor that best characterizes a coordinated turn for a helicopter has been proposed. An analysis has also been completed on the effects of sideslip on the kinematic relationships in a coordinated turn which is based on new closed-form solutions which relate the aircraft angular rates and pitch and roll attitudes to the turn parameters, angle of attack, and sideslip. The results show that the bank angle of the aircraft can differ markedly from the tilt angle of the normal load factor and that the normal load factor can also differ substantially from the accelerometer reading along the vertical body axis of the aircraft. Generally, sideslip has a strong influence on the pitch attitude and roll rate of the helicopter. The study also indicates that pitch rate is independent of angle of attack in a coordinated turn and that in the absence of sideslip, angular rates about the stability axes are independent of the aerodynamic characteristics of the aircraft.

Chen, R. T. N.↗
NASA NTRS1972

Sideslip of wing-body combinations

A small-disturbance theory is developed for predicting the aerodynamics of an airplane in sideslip. Second-order terms involving the interaction between sideslip angle and angle of attack, sideslip angle and wing camber, etc., are retained. It is found that the second-order terms can produce the dominant sideslip effects when the dihedral of the lifting surfaces is small. Numerical implementation of the theory requires a solution procedure capable of producing accurate velocity gradients in the first-order solution.

Rubbert, P. E.↗
NASA NTRS1990

Sideslip-induced static pressure errors in flight-test measurements

During lateral flight-test maneuvers of a V/STOL research aircraft, large errors in static pressure were observed. An investigation of the data showed a strong correlation of the pressure record with variations in sideslip angle. The sensors for both measurements were located on a standard air-data nose boom. An algorithm based on potential flow over a cylinder that was developed to correct the pressure record for sideslip-induced errors is described. In order to properly apply the correction algorithm, it was necessary to estimate and correct the lag error in the pressure system. The method developed for estimating pressure lag is based on the coupling of sideslip activity into the static ports and can be used as a standard flight-test procedure. The estimation procedure is discussed and the corrected static-pressure record for a typical lateral maneuver is presented. It is shown that application of the correction algorithm effectively attenuates sideslip-induced errors.

Parks, Edwin K.↗
NASA NTRS1990

Sideslip-induced static pressure errors in flight-test measurements

During lateral flight-test maneuvers of a V/STOL research aircraft, large errors in static pressure were observed. An investigation of the data showed a strong correlation of the pressure record with variations in sideslip angle. The sensors for both measurements were located on a standard air-data nose boom. This paper descries an algorithm based on potential flow over a cylinder that was developed to correct the pressure record for sideslip-induced errors. In order to properly apply the correction algorithm, it was necessary to estimate and correct the lag error in the pressure system. The method developed for estimating pressure lag is based on the coupling of sideslip activity into the static ports and can be used as a standard flight-test procedure. The paper discusses the estimation procedure and presents the corrected static-pressure record for a typical lateral maneuver. It is shown that application of the correction algorithm effectifvely attenuates sideslip-induced errors.

Parks, Edwin K.↗
NASA NTRS1956

Theoretical span load distributions and rolling moments for sideslipping wings of arbitrary plan form in incompressible flow

A method of computing span loads and the resulting rolling moments for sideslipping wings of arbitrary plan form in incompressible flow is derived. The method requires that the span load at zero sideslip be known for the wing under consideration. Because this information is available for a variety of wings, this requirement should not seriously restrict the application of the present method. The basic method derived herein requires a mechanical differentiation and integration to obtain the rolling moment for the general wing in sideslip. For wings having straight leading and trailing edges over each semispan, the rolling moment due to sideslip is given by a simple equation in terms of plan-form parameters and the lateral center of pressure of the lift due to angle of attack. Calculated span loads and rolling-moment parameters are compared with experimental values. The comparison indicates good agreement between calculations and available experimental data.

Queijo, M J↗
NASA NTRS1958

Some Effects of Horizontal-Tail Position on the Vertical-Tail Pressure Distributions of a Complete Model in Sideslip at High Subsonic Speeds

An investigation has been made in the Langley high-speed 7- by 10-foot tunnel of some effects of horizontal-tail position on the vertical-tail pressure distributions of a complete model in sideslip at high subsonic speeds. The wing of the model was swept back 28.82 deg at the quarter-chord line and had an aspect ratio of 3.50, a taper ratio of 0.067, and NACA 65A004 airfoil sections parallel to the model plane of symmetry. Tests were made with the horizontal tail off, on the wing-chord plane extended, and in T-tail arrangements in forward and rearward locations. The test Mach numbers ranged from 0.60 to 0.92, which corresponds to a Reynolds number range from approximately 2.93 x 10(exp 6) to 3.69 x 10(exp 6), based on the wing mean aerodynamic chord. The sideslip angles varied from -3.9 deg to 12.7 deg at several selected angles of attack. The results indicated that, for a given angle of sideslip, increases in angle of attack caused reductions in the vertical-tail loads in the vicinity of the root chord and increases at the midspan and tip locations, with rearward movements in the local chordwise centers of pressure for the midspan locations and forward movements near the tip of the vertical tail. At the higher angles of attack all configurations investigated experienced outboard and rearward shifts in the center of pressure of the total vertical-tail load. Location of the horizontal tail on the wing- chord plane extended produced only small effects on the vertical-tail loads and centers of pressure. Locating the horizontal tail at the tip of the vertical tail in the forward position caused increases in the vertical-tail loads; this configuration, however, experienced considerable reduction in loads with increasing Mach number. Location of the horizontal tail at the tip of the vertical tail in the rearward position produced the largest increases in vertical-tail loads per degree sideslip angle; this configuration experienced the smallest variations of loads with Mach number of any of the configurations investigated.

Alford, William J., Jr.↗
NASA NTRS1961

Low-Speed Investigation of the Effects of Large Wing-Sideslip Angles on the Aerodynamic Characteristics of Two Arrow-Wing-Fuselage Arrangements

A wind-tunnel investigation has been made of two methods proposed to reduce the high sinking speeds and improve the landing characteristics of low-aspect-ratio hypersonic airplanes by placing the wing at large angles of sideslip to increase its effective aspect ratio. The models investigated had conical fuselages and arrow wings, with a leading-edge sweep-back of 77.4deg, an aspect ratio of 1.23, and a 4-percent-thick straight-wedge section. For one model, the wing was pivoted on the fuselage to angles of wing sideslip from 0 to 90deg. For the other model, the wing was fixed to the fuselage, and the wing and fuselage were yawed together to sideslip angles from 0 to 90deg. The investigation was made in the Langley 300-MPH 7- by 10-foot tunnel for an angle-of-attack range from -8 to above 28deg. Longitudinal stability and control through the use of horizontal tails with elevators was studied on the pivoted-wing configuration. The roll control for both configurations was studied with deflection of the apex portion of the wing about an axis along the wing center line. The use of flaps with the wing at large sideslip angles was also investigated.

Thomas G Gainer↗
NASA NTRS1957

Aerodynamic Loads on Tails at High Angles of Attack and Sideslip

Results are presented for the loads and moments acting on the individual tail surfaces of a body-tail combination over a wide range of angles of attack and sideslip. The effects of forebody length and panel-panel interference on the characteristics are included. It is shown that large nonlinear variations in these loads and moments, which occur at some combinations of angle of attack and sideslip, cannot be predicted by low-angle theory. A relatively simple, but general, theoretical method for calculating these load and moment characteristics is described, and the results from this method are found to be in good agreement with experiment provided the initial positions of the forebody vortices are known. It is shown that a simple application of slender-body theory can be used to predict the side loads due to sideslip that are contributed by a vertical tail on a wide variety of wing-body-tail combinations at low angles of attack. For several configurations, changes are indicated which reduced the vertical-tail loads per unit yawing moment of each complete configuration at large angles of attack. Some results are presented on the effect of high angle of attack on the induced-flow field and tail loads due to a wing at supersonic speed.

SLENDER BODY↗
NASA NTRS1973

Wind-tunnel calibration and requirements for in-flight use of fixed hemispherical head angle-of-attack and angle-of-sideslip sensors

Wind-tunnel tests were conducted with three different fixed pressure-measuring hemispherical head sensor configurations which were strut-mounted on a nose boom. The tests were performed at free-stream Mach numbers from 0.2 to 3.6. The boom-angle-of-attack range was -6 to 15 deg, and the angle-of-sideslip range was -6 to 6 deg. The test Reynolds numbers were from 3.28 million to 65.6 million per meter. The results were used to obtain angle-of-attack and angle-of-sideslip calibration curves for the configurations. Signal outputs from the hemispherical head sensor had to be specially processed to obtain accurate real-time angle-of-attack and angle-of-sideslip measurements for pilot displays or aircraft systems. Use of the fixed sensors in flight showed them to be rugged and reliable and suitable for use in a high temperature environment.

Montoya, E. J.↗
NASA NTRS1975

Effect of combined roll rate and sideslip angle on aircraft flight stability

The combined destabilizing effects of roll rate and sideslip angle are studied for a high angle-of-attack flight condition using a linear simulation of the coupled motions of a Space Shuttle-like configuration. Variations in the eigenvalues for a flight condition nominally identified by an angle of attack of 33.29 deg and a Mach number of 4.9 are examined with illustrations of the separate effects of body-axis roll rate and yaw rate, stability-axis roll rate, dynamic pressure, and sideslip angle. It is shown that the stability of the free motion of the vehicle is sensitive to roll rate and that this sensitivity is enhanced by nonzero sideslip angle. The results suggest that fully coupled linearized equations can be of value both for the study of Space Shuttle stability and for a better understanding of post-stall gyrations, incipient spin, and departure prevention for high-performance aircraft.

Stengel, R. F.↗
NASA NTRS1986

Effects of winglets on a first-generation jet transport wing. 7: Sideslip effects on winglet loads and selected wing loads at subsonic speeds for a full-span model

The effect of sideslip on winglet loads and selected wing loads was investigated at high and low subsonic Mach numbers. The investigation was conducted in two separate wind tunnel facilities, using two slightly different 0.035-scale full-span models. Results are presented which indicate that, in general, winglet loads as a result of sideslip are analogous to wing loads caused by angle of attack. The center-of-pressure locations on the winglets are somewhat different than might be expected for an analogous wing. The spanwise center of pressure for a winglet tends to be more inboard than for a wing. The most notable chordwise location is a forward center-of-pressure location on the winglet at high sideslip angles. The noted differences between a winglet and an analogous wing are the result of the influence of the wing on the winglet.

Meyer, Robert R., Jr.↗
NASA NTRS1961

A Semigraphical Method of Applying Impact Theory to an Arbitrary Body to Obtain the Hypersonic Aerodynamic Characteristics at Angle of Attack and Sideslip

A simple semigraphical method of applying impact theory to obtain the aerodynamic characteristics of an arbitrary body at combined angle of attack and sideslip is presented. The necessary equations are derived, a general procedure for application is outlined, and the effects of graphical errors and areas of application are discussed. One of the features of the present method is the requirement of only one graphical construction for any combination of angle of attack and sideslip. As an example application the present method is applied to a blunted elliptical cone in order to obtain the longitudinal aerodynamic characteristics at an angle of attack of 40 degrees and an angle of sideslip of 0 degrees.

Jackson, Charlie M., Jr.↗
NASA NTRS1962

Tables of Aerodynamic Coefficients Obtained from Developed Newtonian Expressions for Complete and Partial Conic and Spheric Bodies at Combined Angles of Attack and Sideslip with Some Comparisons with Hypersonic Experimental Data

Closed-form expressions and tables composed from these expressions are presented for complete and partial conic and spheric bodies at combined angles of attack and sideslip in Newtonian flow. Aerodynamic coefficients of these bodies are tabulated for various body segments over a range of angles of attack from 1 deg to 85 deg and angles of sideslip from 0 deg to 15 deg. Some comparisons between Newtonian predictions and hypersonic experimental aerodynamic characteristics were made for conic bodies hawing various surface slopes, nose bluntnesses, and body cross sections to indicate the range of validity of the theory. In general, the theory is shown to agree quite well with experimental results for sharp-nose complete cones and for configurations hawing large blunted noses and steep surface slopes. However, agreement between theory and experiment generally is poor for the more slender, slightly blunted complete or half conic bodies and also for sharp-nose half conic bodies where real-flow phenomena such as forebody interference, viscous forces, leeward surface contributions, or leading-edge pressure reductions may have significant effect. The agreement between theory and experiment for the bodies considered can be improved by using the stagnation pressure coefficient behind a normal shock rather than 2 as the Newtonian coefficient, although for the sharp-nose half conic bodies there i s no theoretical justification for this modification.

Armstrong, William O.↗
NASA NTRS1974

Onset of aerodynamic side forces at zero sideslip on symmetric forebodies at high angles of attack

Selected results are presented from extensive wind-tunnel tests that include variations in axial and cross-sectional shape, fineness ratio, bluntness, strakes, and boundary-layer trips over a wide range of conditions (angles of attack to 90 deg, angles of sideslip to 30 deg, Reynolds numbers from subcritical to supercritical, and Mach numbers from 0.1 to 0.7). Pointed forebodies at zero sideslip can experience side forces as large as maximum normal forces. The angle of attack at the onset of side force can be correlated with nose angle and afterbody length. Furthermore, these side forces can be reduced or eliminated by bluntness or nose strakes.

Keener, E. R.↗
NASA NTRS1975

Summary of information on low-speed lateral-directional derivatives due to rate of change of sideslip beta prime

The results presented show that the magnitudes of the aerodynamic stability derivatives due to rate of change of sideslip become quite large at high angles of attack for swept- and delta-wing configurations, and that such derivatives have large effects on the calculated dynamic stability of these configurations at high angles of attack. The wind-tunnel test techniques used to measure the beta prime derivatives and various approaches used to predict them are discussed. Both the conventional oscillating-airfoil theory and the lag-of-the-sidewash theory are shown to be inadequate for predicting the vertical-tail contribution to the acceleration-in-sideslip derivative; a flow-field-lag theory, which is discussed, appears to give qualitative agreement with experimental data for a current twin-jet fighter configuration.

Coe, P. L., Jr.↗
NASA NTRS1982

Flight-determined correction terms for angle of attack and sideslip

The effects of local flow, upwash, and sidewash on angle of attack and sideslip (measured with boom-mounted vanes) were determined for subsonic, transonic, and supersonic flight using a maximum likelihood estimator. The correction terms accounting for these effects were determined using a series of maneuvers flown at a large number of flight conditions in both augmented and unaugmented control modes. The correction terms provide improved angle-of-attack and sideslip values for use in the estimation of stability and control derivatives. In addition to detailing the procedure used to determine these correction terms, this paper discusses various effects, such as those related to Mach number, on the correction terms. The use of maneuvers flown in augmented and unaugmented control modes is also discussed.

Shafer, M. F.↗