Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shape memory effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Intrinsic two-way shape memory effect in a Ni-Mn-Sn metamagnetic shape memory microwire

We report an intrinsic two-way shape memory effect with a fully recoverable strain of 1.0% was achieved in an as-prepared Ni 50 Mn 37.5 Sn 12.5 metamagnetic shape memory microwire fabricated by Taylor-Ulitovsky method. This two-way shape memory effect is mainly owing to the internal stress caused by the retained martensite in austenite matrix, as revealed by transmission electron microscopy observations and high-energy X-ray diffraction experiments. After superelastic training for 30 loading/unloading cycles at room temperature, the amount of retained martensite increased and the recoverable strain of two-way shape memory effect increased significantly to 2.2%. Furthermore, a giant recoverable strain of 11.2% was attained under a bias stress of 300 MPa in the trained microwire. These properties confer this microwire great potential for micro-actuation applications.

36 MATERIALS SCIENCE↗

Shape memory effect in metallic glasses

Shape memory effect (SME), mainly present in crystalline Ti-Ni alloys, is basically missing in metallic glasses (MGs) that lack the long-range periodic order of crystals. In this work, we report experimental results of SME in annealed MGs, in which the low-energy configuration state recovery is observed by both differential scanning calorimetry and X-ray photon correlation spectroscopy. We elucidate the origin of SME in MGs under the potential energy landscape framework, i.e., after annealing, the energy of MGs enters into a deep basin and atoms are located in the low-energy configuration state. Albeit deviating from their relative stable configurations by temperature changes, atoms in the annealed MGs tend to return to the low-energy atomic configurations along certain trajectories as pre-annealing temperature is approached, These results could extend the application of MGs as functional materials by directionally manipulating their energy states via annealing and rejuvenation.

36 MATERIALS SCIENCE↗

Fast-Response-Time Shape-Memory-Effect Foam Actuators

Bulk shape memory alloys, such as Nitinol or CuAlZn, display strong recovery forces undergoing a phase transformation after being strained in their martensitic state. These recovery forces are used for actuation. As the phase transformation is thermally driven, the response time of the actuation can be slow, as the heat must be passively inserted or removed from the alloy. Shape memory alloy TiNi torque tubes have been investigated for at least 20 years and have demonstrated high actuation forces [3,000 in.-lb (approximately equal to 340 N-m) torques] and are very lightweight. However, they are not easy to attach to existing structures. Adhesives will fail in shear at low-torque loads and the TiNi is not weldable, so that mechanical crimp fits have been generally used. These are not reliable, especially in vibratory environments. The TiNi is also slow to heat up, as it can only be heated indirectly using heater and cooling must be done passively. This has restricted their use to on-off actuators where cycle times of approximately one minute is acceptable. Self-propagating high-temperature synthesis (SHS) has been used in the past to make porous TiNi metal foams. Shape Change Technologies has been able to train SHS derived TiNi to exhibit the shape memory effect. As it is an open-celled material, fast response times were observed when the material was heated using hot and cold fluids. A methodology was developed to make the open-celled porous TiNi foams as a tube with integrated hexagonal ends, which then becomes a torsional actuator with fast response times. Under processing developed independently, researchers were able to verify torques of 84 in.-lb (approximately equal to 9.5 Nm) using an actuator weighing 1.3 oz (approximately equal to 37 g) with very fast (less than 1/16th of a second) initial response times when hot and cold fluids were used to facilitate heat transfer. Integrated structural connections were added as part of the net shape process, eliminating the need for welding, adhesives, or mechanical crimping. Inexpensive net-shape processing was used, which reduces the cost of the actuator by over a factor of 10 over nonporous TiNi made by hot drawing of tube or electrical discharge machining. By forming the alloy as an open-celled foam, the surface area for heat transfer is dramatically increased, allowing for much faster response times. The technology also allows for netshape fabrication of the actuator, which allows for structural connections to be integrated into the actuator material, making these actuators significantly less expensive. Commercial applications include actuators for concepts such as the variable area chevron and nozzle in jet aircraft. Lightweight tube or rod components can be supplied to interested parties.

Jardine, Peter↗

Superelasticity and cryogenic linear shape memory effects of CaFe 2 As 2

Shape memory materials have the ability to recover their original shape after a significant amount of deformation when they are subjected to certain stimuli, for instance, heat or magnetic fields. But, their performance is often limited by the energetics and geometry of the martensitic-austenitic phase transformation. We report a unique shape memory behavior in CaFe 2 As 2 , which exhibits superelasticity with over 13% recoverable strain, over 3 GPa yield strength, repeatable stress–strain response even at the micrometer scale, and cryogenic linear shape memory effects near 50 K. These properties are acheived through a reversible uni-axial phase transformation mechanism, the tetragonal/orthorhombic-to-collapsed-tetragonal phase transformation. These results offer the possibility of developing cryogenic linear actuation technologies with a high precision and high actuation power per unit volume for deep space exploration, and more broadly, suggest a mechanistic path to a class of shape memory materials, ThCr 2 Si 2 -structured intermetallic compounds.

36 MATERIALS SCIENCE↗

Fractionation of Lignin for Selective Shape Memory Effects at Elevated Temperatures

We report a facile approach to control the shape memory effects and thermomechanical characteristics of a lignin-based multiphase polymer. Solvent fractionation of a syringylpropane-rich technical organosolv lignin resulted in selective lignin structures having excellent thermal stability coupled with high stiffness and melt-flow resistance. The fractionated lignins were reacted with rubber in melt-phase to form partially networked elastomer enabling selective programmability of the material shape either at 70 °C, a temperature that is high enough for rubbery matrix materials, or at an extremely high temperature, 150 °C. Utilizing appropriate functionalities in fractionated lignins, tunable shape fixity with high strain and stress recovery, particularly high-stress tolerance were maintained. Detailed studies of lignin structures and chemistries were correlated to molecular rigidity, morphology, and stress relaxation, as well as shape memory effects of the materials. The fractionation of lignin enabled enrichment of specific lignin properties for efficient shape memory effects that broaden the materials’ application window. Electron microscopy, melt-rheology, dynamic mechanical analysis and ultra-small angle neutron scattering were conducted to establish morphology of acrylonitrile butadiene rubber (NBR)-lignin elastomers from solvent fractionated lignins.

36 MATERIALS SCIENCE↗

Multilayered microstructures with shape memory effects for vertical deployment

This paper presents a fabrication and characterization of multilayered microstructures with shape memory effects enabling large vertical deployment under electro-thermal actuation. Our previous research demonstrated vertical deployment of such microstructures by the effect of thermal mismatch. Development of equiatomic NiTi layers in the multilayered microstructure is investigated further for shape memory effects. Multilayered microstructures are built by sputtered NiTi layers and a lift-off process. Negative photoresist ma-N1420 enables clean lift-off of 500 nm thick NiTi layers by forming a significant undercut profile after development. The parametric study on co-sputter powers for Ti and Ni 50 Ti 50 targets suggests that 100 W RF on Ti target and 200 W DC on Ni 50 Ti 50 target can deposit Ni 49.62 Ti 50.38 layers. X-Ray Diffraction (XRD) and Atomic Force Microscopy (AFM) were used to study the crystal structures and surface topography of NiTi layers. XRD results of post-annealed Ni 49.62 Ti 50.38 layers show coexistence of austenite and martensitic phases at room temperature, suggesting that the transformation temperature of such NiTi layers should be approximate 20 °C. The surface topography of Ni 49.62 Ti 50.38 layers reveals substantial increase of surface roughness at ambient conditions after the annealing. Experimental verification of the multilayered microstructure for vertical deployment was carried out by Signatone Probe Station and Dual Scanning Electron Microscope/Focused Ion Beam (SEM/FIB) system. Finally, a vertical deployment of the two-dimensional (2D) multilayered microstructures for three-dimensional (3D) can be detected by applying a constant voltage of 0.04 V, and the expected 3D deployment displacement is enlarged from 2 μm to 10 μm by introducing the shape memory effect.

42 ENGINEERING↗

Influence of Detwinning on the Shape Memory Effect in Ni{sub 55}Fe{sub 18}Ga{sub 27} Single Crystals

Deformation mechanisms, one-way and two-way shape memory effects were studied in the mode of compression in the [011] single crystal of the Ni{sub 55}Fe{sub 18}Ga{sub 27} alloy where the detwinning occurred during deformation and in the [001] single crystal where the detwinning was forbidden. It was found that the [001] and [011] crystals deformed by different mechanisms during compression to 5% (reorientation was in [001] crystal, and the reorientation and detwinning were in [011] crystal) and from 15 to 20% (the 14 M → L1{sub 0} transition was in [001] crystal and plastic deformation of 14 M phase was in [011]). The compression of both single crystals from 5 to 15% occurred due to the same mechanisms: the 10 M ↔ 14 M transformation and the plastic deformation of the 14 M martensite. The 14 M and L1{sub 0} phases were stable under load, and they transformed to the 10 M martensite on unloading. It was shown that the crystal orientation and detwinning hardly affected the value of the one-way shape memory effect since both crystals were in the 10 M martensite after preliminary deformation. In this case, the transformation of 10 M martensite to the austenite on heating was accompanied by a strain of about 5% and this was the maximum value of the shape memory effect. It was found that the detwinning significantly affected the temperature ranges of strain recovery. In the [011] crystal, the strain recovered in a very narrow interval on heating (1-2°C), whereas in the [001] crystal the shape memory effect was observed in “normal” temperature range (~ 10°C). The detwinning resulted in the formation of a large oriented internal stress during the preliminary deformation that increased the value of the two-way shape memory effect that was observed in [011] crystals in comparison with the [001] crystals.

36 MATERIALS SCIENCE↗

Controlling shape memory effects in NiTi thin films grown on Ru seed layer

NiTi thin films with robust shape memory effects and low deposition temperatures are greatly desired for microelectronic devices. However, sub-micron films deposited below 425 °C usually have amorphous structure and must be post-annealed to achieve full crystallization. In this article, using Ru as a seed layer, we demonstrate growth of NiTi films as thin as 120 nm with in-situ crystallization at 325 °C. NiTi thin films with a wide range of growth parameters including deposition temperature and film thickness were investigated. Shape memory effects were characterized using stress bow and resistivity studies. Structural information across the R-phase to austenite transformation was obtained using X-ray diffraction. NiTi thin films exhibited a narrow hysteresis during R-phase to austenite phase transition near 60 °C while possessing good shape memory properties.

36 MATERIALS SCIENCE↗

Fast Response, Open-Celled Porous, Shape Memory Effect Actuators with Integrated Attachments

This invention relates to the exploitation of porous foam articles exhibiting the Shape Memory Effect as actuators. Each foam article is composed of a plurality of geometric shapes, such that some geometric shapes can fit snugly into or around rigid mating connectors that attach the Shape Memory foam article intimately into the load path between a static structure and a moveable structure. The foam is open-celled, composed of a plurality of interconnected struts whose mean diameter can vary from approximately 50 to 500 microns. Gases and fluids flowing through the foam transfer heat rapidly with the struts, providing rapid Shape Memory Effect transformations. Embodiments of porous foam articles as torsional actuators and approximately planar structures are disposed. Simple, integral connection systems exploiting the ability to supply large loads to a structure, and that can also supply hot and cold gases and fluids to effect rapid actuation are also disposed.

Jardine, Andrew Peter↗

Enhanced magnetic hysteresis in Ni-Mn-Ga single crystal and its influence on magnetic shape memory effect

Enhanced magnetic hysteresis due to boron doping in combination with magnetic shape memory effect in Ni-Mn-Ga single crystal results in new interesting functionality of magnetic shape memory (MSM) alloys such as mechanical demagnetization. In Ni{sub 50.0}Mn{sub 28.5}Ga{sub 21.5} single crystal, the boron doping increased magnetic coercivity from few Oe to 270 Oe while not affecting the transformation behavior and 10 M martensite structure. However, the magnetic field needed for MSM effect also increased in doped sample. The magnetic behavior is compared to undoped single crystal of similar composition. The evidence from the X-ray diffraction, magnetic domain structure, magnetization loops, and temperature evolution of the magnetic coercivity points out that the enhanced hysteresis is caused by stress-induced anisotropy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fast Response Shape Memory Effect Titanium Nickel (TiNi) Foam Torque Tubes

Shape Change Technologies has developed a process to manufacture net-shaped TiNi foam torque tubes that demonstrate the shape memory effect. The torque tubes dramatically reduce response time by a factor of 10. This Phase II project matured the actuator technology by rigorously characterizing the process to optimize the quality of the TiNi and developing a set of metrics to provide ISO 9002 quality assurance. A laboratory virtual instrument engineering workbench (LabVIEW'TM')-based, real-time control of the torsional actuators was developed. These actuators were developed with The Boeing Company for aerospace applications.

Jardine, Peter↗

Biobased Semi-Interpenetrating Polymer Networks of Poly(ε-caprolactone) and Epoxidized Soybean Oil with Nanoscale Morphology, Shape-Memory Effect, and Biocompatibility

Creating biobased polymer blends with outstanding properties, nanoscale morphology, shape-memory capability, and biocompatibility is very crucial and requires a fundamental understanding of the phase behavior, macromolecular structure, and biological compatibility of the polymer blends with living cells. It is very critical to understand the complex relationships among the polymer structure, morphology, and performance of multifunctional smart materials under conditions that they are likely to encounter during use, particularly in biomedical applications. Biobased semi-interpenetrating polymer networks of poly(ε-caprolactone) and epoxidized soybean oil with nanoscale morphology have been successfully synthesized via in situ cationic polymerization and compatibilization in a homogeneous solution. Varies analytical and characterization techniques, such as Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, transmission electron microscopy, X-ray scattering, cell toxicity, and shape-memory effects (SMEs), have been employed to understand the structure–properties relationship of these smart, biobased nanostructured polymer blends. The synthesized nano blends were nontoxic or biocompatible and supported attachment of human vein endothelial cells, showing their potential use in biomedical applications. The current versatile, low-cost strategy for synthesizing the nanoscale morphology of semi-interpenetrating polymer networks with SMEs and biocompatibility should be widely applicable for polymer systems. This study is also considered as a continuation to our efforts in the area of biobased polymers to develop innovative technologies to transform natural resources into smart multifunctional materials for a wide range of applications, including coatings, adhesives, and medical devices.

36 MATERIALS SCIENCE↗

Mechanism of the Influence of Poly- and Nanocrystallinity on the Parameters of Pseudoelastic Deformation Curves of Alloys with the Shape Memory Effect

The influence of poly- and nanocrystallinity on the parameters of pseudoelastic deformation curves of alloys with the shape memory effect (SME) has been analyzed within the theory of diffuse martensitic transformations. The functional and quantitative dependence of the coefficient of deformation (martensitic) hardening of an alloy with the SME on the grain size d and orientational factor M, dσ/dε ~ 1/Md{sup 2}, has been obtained for the first time, taking into account the normal distribution density of grains over their orientations and the log-normal distribution density over grain sizes d. A comparison of the found dependence with the data in the literature for a nanocrystalline TiNi alloy with nanograin sizes in the range of 8–90 nm shows good consistency between the theory and experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanism of Influence of Nanocrystal Sizes on the Parameters of the Curves of the Pseudoelastic and Thermoelastic Deformations of Alloys with the Shape Memory Effect

The data available in the literature on the influence of the nanocrystal sizes of alloys with the shape memory effect on the parameters of the curves of their pseudoelastic and thermoelastic deformation are analyzed in the framework of the theory of diffuse martensitic transitions (DMT). The peculiarity of the DMT theory is that it is based on both thermodynamic and kinetic relationships that make it sensitive to the alloy structure on the mesoscopic scale. This enables one to state the functional dependence of the parameter of the martensitic deformation of the nanocrystals on the size of their cross section D. As a result of the analysis, it is found that the coefficient of the strain (martensitic) hardening and the hysteresis of the pseudoelastic strain curves of submicrocrystals of the Ni{sub 54}Fe{sub 19}Ga{sub 27} are changed with D by law 1/D{sup 2}. The temperature range (M{sub s} – M{sub f}) of the martensitic transition in TiNi alloy nanocrystals is changed by analogy law. These dependences are results of the constrained displacement of dislocations of the phase transformation by transverse sizes of the crystal. A kinetic mechanism of the appearance of the critical nanocrystal size D{sub k} is established; the transition of austenite to martensite does not occur at transverse crystal sizes smaller than the critical size.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗